ender 3 v2 dual z 3d models

... as long as both sides are equal. After levelling the gantry, use the move menu to travel the Z axis all the way up and back down then measure it again. Keep adjusting until it stays level. ...The Z end-stop will need to be relocated as pictured.

--- # new ones: ** https://cults3d.com/en/3d-model/tool/z-motor-mount-single-dual-ender3-pro-v2 ** --- two options: - one with an extra vertical support that slides on the side Y beam. it will keep the motor elevated, not touching the side Y beam,...

Other hardware can be reused from stock Ender 3 PSU. Install sequence;Screw the mains socket into bracket without connecting the PSU. bolt down the empty bracket. Snake the 24V cable through one of the rear pass through. Lay the PSU on the build...

The [Dual Z Ender 3 Complete System by andrei66](https://www.thingiverse.com/thing:4373101) looked really nice, but I only needed the X gantry mount, I wanted to use the awesome [Ender 3 / Pro / V2 Dual Z Axis Motor Mount by...

**Non-Stock Parts Needed - Stock Bracket Replacement** - 1x M8 washer (to place under the eccentric nut so it doesn't wear through the plastic) - Suitable motor (NEMA17, get one like the ones on the Ender 3) **Non-Stock Parts Needed - Second Z...

I remixed mlynch002's design because I wanted my printer in the original location, so my ender would fit better on my desk after adding the dual Z screw. I highly recommend the dual Z upgrade, and my remix uses about half the filament and print time...

I remixed mlynch002 because I wanted my in the original location and so my ender would fit better on my desk after the dual Z screw was added. Would highly recommend the dual z, and my remix of his design uses about half the filament / print time,...

This is a remix using tinkercad.com to remove a 30x3 mm section to wrap around the x-axis belt tensioner on my Ender 3 v2. The tensioner sticks out so the part that takes the place of the spacers can not lay flat without removing some of the part. ... ...

Wiring: So far, I've only tested wiring a second stepper in parallel with the original stepper, increasing current to 1 amp (Skr 1.3 with 2208). Also, my second stepper is different from the original Creality stepper, which isn't recommended. I'll...

Parts: KLF08 Bearings: https://de.aliexpress.com/item/32793159224.html Ender 3 Rod: https://de.aliexpress.com/item/32904246004.html GT2 Timing Pulley: https://de.aliexpress.com/item/33017482340.html GT2 Belt Joining:...

I have Ender 3 V2 with Dual Z and extended Z axis. I am using CHEP's rear spool mount with extruder turned 90 degrees. https://www.thingiverse.com/thing:4309135 During print I noticed that the cables sometimes get stuck with the spool holder and...

Gantry Dual Z Ender 3 MAX

Replacement for Creality part. ...Allows adjustment of z-screw position.

Z spacer for dual collision of the inner rollers for aligning and syncing dual stepper motors of the Ender 3. ...

Remixed The Tool Holder to work with a dual z on a ender 3 pro

I modified my Ender 3 with Ender Extender 300 and wasn't sure which belt to get. I bought the 840mm belt. This tensioner works with the dual z components and helps take out the extra slack in the belt. ... You will also need a bearing (7mm tall,...

I retrofitted my Ender 3 with a belt-driven dual-Z kit, which works really great. ...Wanting to see how much and when the adjustments from the auto bed levelling make it over to the second Z spindle, I designed this pointer.It fits on the top of the 16...

I retrofitted my Ender 3 with a belt-driven dual-Z kit. Wanting to see how much and when the adjustments from the auto bed levelling make it over to the second Z spindle, I designed this pointer. ... It fits on the top of the 16 mm OD belt sprocket...

Hi, Dual Z bracket/mount for Ender 3 / Ender 3 Pro, (for use with anti backlash nut, mounted at the bottom) no need for extra hardware. The screw mounting hole is at exactly same level/height as original one on the other side. This is a a bit lighter...

Monolith Ender 3 dual Z-axis aligner inspired by 2001: A Space Odyssey.I couldn't find proper tool to align my Z-Axis after installing dual Z-Axis mod for my somewhat modded Ender 3 Pro. The found solutions didn't quite fit for my use, some because...

A custom-designed dual Z-axis drive setup is created specifically for the popular Creality Ender 3 3D printer model. This innovative solution utilizes the MGN12 linear guide, which can be sourced from Thingiverse's item number 3025419. To...

Minimum belt size: 670mm (measured and tested) Maximum belt size: 700mm-ish (696mm pictured) BOM: 20T pulley: https://www.amazon.com/dp/B08TV1NF4B 40T pulley: https://www.amazon.com/dp/B07ZKF7G5G Dual Z kit:...

I retrofitted my Ender 3 with a belt-driven dual-Z kit. ...Wanting to see how much and when the adjustments from the auto bed levelling make it over to the second Z spindle, I designed this pointer. It fits on the top of the 16 mm OD belt sprocket with...

This is my take on Ender 3 Max dual Z axis update. ... I did use closed loop belt 852mm from here: https://www.aliexpress.com/item/32971350055.html Belt tensioner (or belt cut to size - glued and sawn): https://www.thingiverse.com/thing:4796015 also...

Hi, Dual Z bracket/mount for Ender 3 / Ender 3 Pro, no need for extra hardware ;-) enjoy Print: 0.2 height 4-6 walls 40% infill support: YES Position on bed: As shown on a picture Offset bracket for PSU https://www.thingiverse.com/thing:4610070 Z...

The Ender 3 Pro BLV dual Z upgrade kit from Aliexpress appears to be missing crucial components (a single spacer, for instance). To rectify this issue, I created a custom replacement spacer.\r\n\r\nNotably, the seller has now acknowledged these...

This remix is designed for Ender 3 users that have installed a second Z drive. ...You will need 4 M4 bolts and 4 M4 T-nuts.

These parts, in conjunction with a dual Z-axis upgrade kit for a CR-10, allow the Ender 3 to be upgraded to dual Z-axis using a belt system to keep the 2 leadscrews synchronised. The dual Z-axis upgrade kit comes with the plate and mounting hardware...

I designed a dual Z axis mod for my Creality Ender 3, but I wanted it to look similar to the CR-10S's design. Since there was one available, I edited and borrowed files from the CR-10 OEM - Complete 3D Model, CR-10 Dual Z-Axis Belt Synchronizer, and...

just a spacer required to assembly hunterius_prime's dual z carriage