ender 3 v2 display 3d models

This is my remix of Satsana 5015 Fan Duct that could be used on ender 3 v2 I've used Fan 4010 but 4020 will work too. I highly recomend to go something low db and good m3/h speed. Maybe I will consider noctua for that one in future. Recomendation...

A Fan shroud for the Ender 3 v2 to fit the “MBOT3D MK2 Remix (Ender7 style fan duct with dual 4010 fans)” - air ducts. https://www.printables.com/model/158236-mbot3d-mk2-remix-ender7-style-fan-duct-with-dual-4/filesThe front plate is made to print...

cover to put switch on the front of the ender 3 v2, so it will no longer be so annoying to reach backwards. The switch I use is the one that comes with the printer, so I have to remove the cover of the power supply to put new cables of appropriate...

I designed a MK8 nozzle holder that makes use of the small compartment inside the Ender 3 V2 drawer. It is designed so it can printed without supports. It is printed face down, with basic cura settings it only takes about 2 hours. The main...

I just got an Ender 3 V2 (my first 3d printer) and I still don't have a home for it and I've been keeping it where it's somewhat easy for my 2-yo to reach and play with the knob (I plan to find a safe place around my house for the printer). So i...

I made a flippable screen cover for the Ender 3 V2 screen since I haven't seen any designs like this so I created my own. I designed a screen cover that uses a hinge system allowing users to open and close it whenever needed. The main purpose was to...

This rack is designed to fit into the side slots on an Ender 3 V2 Neo. It may fit other models, but I can't guarantee that.It holds the tools that don't fit into the provided drawer, namely the scraper and nippers. It also has slots to hold a small...

''I had enough of the tools rattling each time i would open the drawer and getting all mixed up after i organised them.''  Drawer organiser for the Ender 3 V2: -Will hold all allen/hex keys, wrenches, original bed clamps, 7mm capacity paper clamps...

#Description The Ender 3 V2 control board is mounted a upside down from the previous Ender 3's, so it is accessed by removing the bottom panel of the surrounding shell.as opposed to the top panel on previous Enders. This makes for a harrowing...

I bought one of those "cheap" "3DTouch" devices which claimed to suit the Ender 3 V2. The correct mount (and the cable supplied) doesn't fit the V2. You can cut and drill the supplied mount and it will fit but my supplied 3DTouch is a bit longer...

If you have any suggestions for improvement or want to communicate with me, please visit my development community and leave a message, I will reply you as soon as possible:...

But that spacer doesn't isolate display properly, display still stay connected thru bolts, so i redesigned it, now everything isolated properly and my display has no interference problems so far. ...Also two additional M3 bolts needed to attach display...

Unitl I found this model: https://www.thingiverse.com/thing:2552992 I liked the idea of this mount and changed it so it would fit on the rails of my Ender 3 V2. This is my first model ever edited/created, so every feedback is welcome. I put 2...

Simple display mount that changes the angle and insets the display, as I have it hung over a desk and wanted it to stick out less. ... Also thinking about building a modular display mount that can be rotated

The fan bulge protrudes 8mm below the power supply, and your Ender 3 v2 has 12mm of under-side space available. This makes it a tight fit with just 4mm of space for air to travel through. After careful consideration, I positioned my fan to blow air...

This is a simple print station for an Ender 3 V2, it uses pieces of window wiper to clean the nozzle in 3 directions. To use: Cut 3 sections of window wiper or other heat resistant material into 10mm x 20mm pieces and hot glue them into the holes. ... ...

... knife/scraper thing. Mine simply has a flat plastic piece that attaches to the blade, so I widened and deepened the slot and removed the curve from the original design. In the end the tool holder fits all the tools that came with my Ender 3 v2.

This may help with your display randomly clicking while printing. ...Might be better printed in a flexible filament.

Some slightly soft material for button levers to switch Just a few parts to print, and you're ready to start: (1) Mainframe / Mainframe_Roundup (2) Topside (3) Displaypins (4) Encoder_Frame (5) Encoder_Cap (6) Encoder_Nut Assembly instructions are...

I encountered frustrating connectivity issues and noticed my screen suddenly displaying a foreign language, but I successfully resolved the problem using this solution.

I redesigned it to better fit the unique space where I have my printer proudly displayed on a shelf, rather than being confined by an awkward original angle.

So i got sick of my guide that i printed off here falling off when using my sunlu filament dryer so i made my own that bolts to the gantry of my Ender 3 V2. No extra parts needed, bolts onto gantry roller nut. I find its still easy to load filament...

This tray works by hanging on the curved drawer walls built in to the Ender 3 v2 drawer. I designed it to hold 8 spare nozzles, 4 replacement silicone socks, a nozzle clearing needle and the wrenches that came with the printer while still leaving...

Ender 3 v2 Bowden clips. I used the MIKA3D Silk Copper because I was at the end of the spool and didn't feel like changing out. In the future, I would probably use Hatchbox Black. I would also probably change the quality from 0.2 to 0.16 just to...

I have created this bearing filament guide to help the Creality Ender 3 V2 to get the filament from the spool with less friction, better angle. It works as for now, no failure yet caused by the spool/filament feed. Printing: I have printed the...

This filament guide is for the Ender 3 v2, and slides over the existing metal spool holder bracket. I found one like this on Thingiverse that worked pretty good except it didn't have any support at the base to keep it level, so it kept angling...

... the color. I printed this on an Ender 3 V2 and it did fit perfect. Earlier I printed this on a 5 year old Monoprice printer and they were almost snug. ...I had to use a hear dryer to get the pieces warm to get them over the bearing and load cell.

This is a (to the best of my abilities) a complete model of the Creality Ender 3 V2, that can be downloaded and edited. The goal of which to allow a user to design parts and test for the physical machine. To my knowledge all of the parts should be...

You will need to print with supports, the current design suits standard Ender 3 V2 and also has a cutout for the mounting screw if you have a fang. (refer to .stl - photo shows V1 with smaller cutout) To use this simply lift the Z Axis to 120mm,...

Spray Bottle Holder that slots into the rails on a Ender 3 V2. Was looking for a place to store spray bottles of Isopropyl and Acetone used to clean my print bed in between prints. Made this very basic bottle holder based on spray bottles I...