ender 3 v2 direct drive 3d models

Remix for use in Unitak Direct Drive Upgrade Kit for Ender 3v2. https://www.amazon.com/gp/product/B09KG8MMQ2/ref=ppx_yo_dt_b_asin_title_o03_s02?ie=UTF8&psc=1 *The part was rotated 2 degrees to align with the mounting plate. *Added support...

SummaryA fan shroud that is compatible with a sideways direct drive mount, with the extruder motor protruding on the left side.

NOTE: Been on 3 days, just finished a 30 hrs print, perfect, but led's are suffering a little sag and when they were warm ive had to push them back into there holes, but theyve settled in with a tiny bit of droop but are fine. I will at some point...

NOTE: Been on 3 days, just finished a 30 hrs print, perfect, but led's are suffering a little sag and when they were warm ive had to push them back into there holes, but theyve settled in with a tiny bit of droop but are fine. I will at some point...

This is a variation of the Ender 3 V2 Direct Drive model from JamieBK. I used it to allow a Creality brand laser engraver (mounted with bracket by TerryYoung2003) to fit on the side of the hotend casing. ...Works very well on my Creality Ender 3 V2 with...

This is remix for Petsfang Blokhead|Bullseye Direct Drive|BMG|Titan|Orbiter|CR10|S|S4|5 Ender|3|3v2|4|5+|Tornado...

This setup combined with an SKR v1.3 running Marlin 2.0 has enabled my ender 3 to hit printable layer heights as low as 0.04mm, or 40 microns. It takes forever to print at that low a layer and the leveling has to be flawless, but it worked. I rarely...

Minimalist, simple and efficient with a very limited budget to be able to print almost any filament while keeping, at most, the original characteristics of the Ender 3 link of the video for the assembly with explanations and additional links:...

This is for Ender 3 v2 with direct drive setup. Filament sensor mounted on top next to the spool. May have issues if printing too high because filament sensor is stationary while hot end is moving, causing filament coming out of the sensor to...

Remix of [jkostenov's bltouch mount](https://www.thingiverse.com/thing:4462870) for the Ender 3 V2 to allow for [the direct drive](https://www.thingiverse.com/thing:4555065)

... screwed it into the guide. I also tried to get everything to line up straighter and rub less on the screw guard Had to realign for the Ender 3 V2 With a MicroSwiss direct drive setup. ...Also allows for easy attachment of a filament runout sensor.

remixed to be compatible with bmg and hero me gen 5 ender 3 V2

Update December 3, 2020 I remixed fan duct and made my own direct drive bracket. https://www.thingiverse.com/thing:4674061 Update: November 25, 2020 I uploaded a couple of photos and another cable cap that covers the entire cut out. One photo...

I installed a direct drive unit on my Ender 3, which required me to rotate the filament spool 90 degrees. To accommodate this change, I needed a new filament guide that would hold its position. I was previously using...

This is a simple design to be able to install the hot end fan and the part fan on a new Micro Swiss Direct Drive. Since the original hard ware will not fit the new part, here is a solution. ... Just change the parts Fan Nozzle 4 mm and centered with the...

After I convert my printer to direct drive my extruder cables were touching the Z rods. I don't like cable chains so I need a solution for cable management.&nbsp;</p><p>The guide has a 90 degrees angle in order to better route the wires and it is...

I ma not sure if HKFEVER made a file for the stock extruder, but this is for the stock extruder on the E3MAX.

Simple anti z-wobble device for Ender 3 / 3 Pro / 3 V2 Simply device for reducing z-wobble caused of low quality lead screw. This is remix of https://www.thingiverse.com/thing:4387638. Use 10 small neodymium magnets (8x3mm) and balls from baering...

Hello, I recently modeled and tested a tab to make a creality Ender 3 v2 a direct drive.5 printer that should also work on other printers from creality but this has yet to be confirmed) This last one allows to print all kind of filaments including...

Just my design of a fan bracket to Direct Drive Swiss, you need glueing 2 fans (Stock ender 3 V2), Screw M2 35 mm

Made a rough version that doesn't interfere with Z axis nut for direct drive converted setups. ... Currently using it with this: https://www.thingiverse.com/thing:4789619 Slim links can still be acquired from remix source: ...

... 4 holes M4, for any improvements later, like aditional filament guide, or filament runout sensor. 3 holes for filament sensors are 8 mm diameter, top of holes are 9 mm diameter for around 5 mm height. ...Used M4 tube holders with longer body.

Printable ender3 direct drive upgrade compatible with Orbiter V2.0 Extruder.

People with an Ender 3 or Ender 3 Pro who have installed a direct drive conversion, like my basaraba_innovations kit, can benefit from a filament runout sensor. To install this feature, you will need the following additional items: * A small piece...

I needed a filament sensor guide that works with a direct drive to go with my cheap Amazon filament sensor. Use a zip tie to secure the filament sensor to the mount. I designed it with a zip tie vs using the holes because it seems that many of the...

I needed a filament sensor guide that works with a direct drive to go with my cheap Amazon filament sensor. Use a zip tie to secure the filament sensor to the mount. I designed it with a zip tie vs using the holes because it seems that many of the...

Filament Sensor: BigTreeTech Filament Break Detection Module For 1.75mm https://www.aliexpress.com/item/33028816768.html

https://www.thingiverse.com/thing:4441076 presented a thumb screw to replace the wing nut on the front-left corner of the BIBO bed. It is too wide for the other two positions. I have created a smaller version to fit the right-front corner and the...

Thickness about 30mm clone titan direct drive braket for ender 3 v2 head set~! M3 nut is mini satsana or satsana duct fix part for ender 3 v2. This is not required if other ducts are used. ... Remix free~!!

this is a direct drive converter made to combine OMG v2 extruder + nema pancake stepper motor to be install on the original x-carriage plate on ender-3. ...