ender 3 v2 direct drive 3d models

... but it works great so far. All For Stock ENDER 3 V2 parts, only thing you'll need is some screws and a short bowden tube, not sure about the length I just cut it to fit, easy to do. ... Highly recommend dual Z axis upgrade to help with any sag.

The objective was to get the lightest and simplest set, using: - 4010 fan to the heatbreak - dual 4010 blower fans for filament cooling - BLTouch support - Extruder Stepper motor support (works with stock Ender 3[v2] or pancake) Print Tips Preferred...

The objective was to get the lightest and simplest set, using: - 4010 fan to the heatbreak - dual 4010 blower fans for filament cooling - BLTouch support - Extruder Stepper motor support (works with stock Ender 3[v2] or pancake) Print Tips...

Remix of [JamieBK's direct drive mount](https://www.thingiverse.com/thing:4555065) that uses the dual gear drive extruder used with CR10

I remixed the excellent Ender 3v2 direct drive adapter by Peviox (https://www.thingiverse.com/thing:5216067) with enough clearance for a 20mm fan on top of the Briss Moto duct and added a mount for the slim cable chain by norp...

I remixed the excellent Ender 3v2 direct drive adapter by Peviox (https://www.thingiverse.com/thing:5216067) with enough clearance for a 20mm fan on top of the Briss Moto duct and added a mount for the slim cable chain by norp...

... that i have been able to finally create my own model of satsana. This sastana has 3 front mount screws. CR / BL Touch adapter. Direct drive adaptation. And stock parts / Fans only. An amazing piece. ...i hope others are in need of this as i was.

... i have been able to finally create my own model of satsana. This sastana has 3 front mount screws. CR / BL Touch adapter. Direct drive adaptation. And stock parts / Fans only. An amazing piece. ...i hope others are in need of this as i was.

This is a remix that allows you to mount the extruder sherpa mini or sailfin to "Ender 3 v2" along with the E3D V6 hotend and CR / BL Touch. For the remix I used this project because it is very solid, the hotend does not wobble sideways unlike other...

This design is made to accommodate the position of the filament sensor for direct feed. I matched the screw holes to the sensor I purchased. Other models may require a different position of the screws. ... The device is adjusted to the top profile of...

Make the satsana duct compatible with https://www.thingiverse.com/thing:4621486 Follow the original authors' print settings.

I originally used this model to mount 3 noctua fans to my Ender 3 V2. When I decided to go direct drive there were no options for the V2 with 2 part fans. I took the original files from Bantam Designs and modified them to fit. I printed in PLA at...

Ender 3 V2 Neo mit Direct-Drive und Filament Rollenhalter wenn man die Filament Rolle an der Seite des Druckers montieren möchte. Direct Drive mit folgendes Teil umgebaut: https://www.thingiverse.com/thing:5813643 Um die Filament Rolle an der Seite...

I've remixed napfkuchen's BMG direct drive design to fit the Ender 3 V2's x-carriage as the mounting hole for the fan shroud is in a different location when compared to the Ender 3. The Bl-touch has also been added in as the two parts would...

... fans and direct extruder. ...If you want to use direct extruder it might be the best to use my mount https://cults3d.com/en/3d-model/various/ender-3-v2-direct-extrusion-mount-for-dual-gear Easy install with 1 screw. ...You might also need 2 doodly eyes

I wanted something for the Ender 3 V2 with Micro Swiss Direct Drive that was effective but not over the top. I wanted to upgrade to dual 5015 blowers for part cooling so here we are. The "AeroSpike". This model isn't the easiest to print. It...

Remixed from : Voron afterburner mount for Ender 3 (bmg direct drive) by igalopaka https://www.thingiverse.com/thing:4614384 BlTouch addon inspired by: Voron Afterburner with Bltouch for Ender 3, CR-10, etc. by TroyJoachim...

I was building and ender from some spare parts and needed a hotend plate, but decided to go further and directly combine it with direct drive mod. so far working fine. tightening the belt too much may break it, but who cares. ...just print a new...

This is an adapter for stock Ender 3 style spool holder. The adapter slides into a 2020 extrusion and uses two M5 screws for mounting the stock part. ...The mounting surface is angled at 45 degrees. Supports: NoMaterial: PLA or PETGLayer Height:...

This is a modification of OpenDorrPolicy's Ender 3 Max drag chain mount, modified to reduce the X axis loss and to incorporate a Z axis chain connector as in Ilueen's thing. It also adds two zip tie holes on the mount where the extruder normally...

... design of fan shroud. I have not mounted it yet. But I did use measurements from the remixed part the V2 carriage model and my printer to make the changes. Added V2 mount that has mounting points for all the holes on a V2 X-carriage. ...

Mod has not been tested but it should work, I'm running a dual gear extruder but this mod will allow you to use the stock extruder with your v2 neo. ... Youtube Channel: https://www.youtube.com/@zeltroix Buy me a coffee:...

I uploaded a few versions, I haven't really found a good orientation to print the thicker revision. I made these pretty quickly w/tinkercad, perhaps I'll remake/re-remix them in blender or fusion 360 in the future. ... Currently using it with this...

Support filament pour mettre sur la machine avec rail simple standard Filament holder to put on the machine with standard single rail

<p>I created this remix because the original version was a bit larger than I needed, and I wanted to fit the cables in more snug. The original also broke when I went to attach the zip-ties, one bit snapped off. It was still usable, but I figured I'd...

I converted my Ender 3 to direct drive with the BIQU H2 and needed a guide to keep the filament from unspooling or getting tangled. The static ones I saw online didn't work great, so I designed this one to move up and down and left and right to...

Behold! A front facing DD mod for these printers, or is it backwards facing? Anyways I like the look of this, plus it doesn't affect your max Z height. Check out my channel I'll upload an installation guide soon No additional hardware...

I designed this for my Ender-3 v2 with the Creality Titan Direct Drive using TinkerCAD, https://www.tinkercad.com/things/jnTaDbgEz4M . I was inspired by the Creality CR-10 Smart Pro FRS mount. My original design did not swivel and caused binding...

I designed this for my Ender-3 v2 with the Creality Titan Direct Drive using TinkerCAD, https://www.tinkercad.com/things/jnTaDbgEz4M . I was inspired by the Creality CR-10 Smart Pro FRS mount. My original design did not swivel and caused binding...