ender 3 v2 dimensions 3d models

I designed a MK8 nozzle holder that makes use of the small compartment inside the Ender 3 V2 drawer. It is designed so it can printed without supports. It is printed face down, with basic cura settings it only takes about 2 hours. The main...

''I had enough of the tools rattling each time i would open the drawer and getting all mixed up after i organised them.''  Drawer organiser for the Ender 3 V2: -Will hold all allen/hex keys, wrenches, original bed clamps, 7mm capacity paper clamps...

I designed this simple pen holder for ender 3 v2. It's very easy to install. You need to use super glue/hot glue to mount first part to the printer (it can be at a slight angle to the nozzle), then you have to put a pen/marker in a second part and...

... the mount in place of the larger idler wheel mount screw. I believe they are m2.5x0.45 screws. I used the wiring guide and configuration/firmware found here: https://smith3d.com/ender-3-v2-bltouch-firmware-installation-guide-by-smith3d-com/

In my eyes, this is a decent-looking display cover for the Ender 3 V2 3D printer that prevents both dust from getting on the screen, and light from getting out when it's not wanted. It's slightly inspired by Forerunner architecture from Halo. ...The...

This rack is designed to fit into the side slots on an Ender 3 V2 Neo. It may fit other models, but I can't guarantee that.It holds the tools that don't fit into the provided drawer, namely the scraper and nippers. It also has slots to hold a small...

The stock cooling duct on my Ender 3 V2 did not cool the back of the part well. I designed this to help improve that. I wanted to keep the stock parts and look. I added two flow straighteners. From my experience, the blower fan pushes all the air to...

I just got an Ender 3 V2 (my first 3d printer) and I still don't have a home for it and I've been keeping it where it's somewhat easy for my 2-yo to reach and play with the knob (I plan to find a safe place around my house for the printer). So i...

A Fan shroud for the Ender 3 v2 to fit the “MBOT3D MK2 Remix (Ender7 style fan duct with dual 4010 fans)” - air ducts. https://www.printables.com/model/158236-mbot3d-mk2-remix-ender7-style-fan-duct-with-dual-4/filesThe front plate is made to print...

I designed it and used it with satisfaction on my Creality Ender 3 V2. They absorbe the X and Y action (which creates the most thumping movement sound) -The height allows for better airflow underneath the printer. -The balls allow for better...

This is a handle designed for the Ender-3 v2 bed. The front two bed fasteners pass through the two holes on the handle and the springs rest in the counter bore/ slots. The locknuts go on the under-side and hold the handle in place. The arches...

A Fan shroud for the Ender 3 v2 to fit the “MBOT3D MK2 Remix (Ender7 style fan duct with dual 4010 fans)” - air ducts. https://www.printables.com/model/158236-mbot3d-mk2-remix-ender7-style-fan-duct-with-dual-4/filesThe front plate is made to...

Mixup of the Voron Trident skirting and tops for the ender 3 v2.The logo's can be hard to press in a bit of heat goes a long way to helping.Make sure to print the 4 extension feet and use your stock rubbers.I just glued on the “dummy” front feet….

I have an Ender 3 v2 and I didn't want to obstruct the tool drawer or rely on the bottom left groove only, so I remixed darkpoet's excellent design to utilize the left corner. Also I maintained the angle of the holder, but I made the piece flat...

cover to put switch on the front of the ender 3 v2, so it will no longer be so annoying to reach backwards. The switch I use is the one that comes with the printer, so I have to remove the cover of the power supply to put new cables of appropriate...

This is my remix of Satsana 5015 Fan Duct that could be used on ender 3 v2 I've used Fan 4010 but 4020 will work too. I highly recomend to go something low db and good m3/h speed. Maybe I will consider noctua for that one in future. Recomendation...

''I had enough of the tools rattling each time i would open the drawer and getting all mixed up after i organised them.'' Drawer organiser for the Ender 3 V2: -Will hold all allen/hex keys, wrenches, original bed clamps, 7mm capacity paper clamps and...

I made a flippable screen cover for the Ender 3 V2 screen since I haven't seen any designs like this so I created my own. I designed a screen cover that uses a hinge system allowing users to open and close it whenever needed. The main purpose was to...

#Description The Ender 3 V2 control board is mounted a upside down from the previous Ender 3's, so it is accessed by removing the bottom panel of the surrounding shell.as opposed to the top panel on previous Enders. This makes for a harrowing...

I bought one of those "cheap" "3DTouch" devices which claimed to suit the Ender 3 V2. The correct mount (and the cable supplied) doesn't fit the V2. You can cut and drill the supplied mount and it will fit but my supplied 3DTouch is a bit longer...

If you have any suggestions for improvement or want to communicate with me, please visit my development community and leave a message, I will reply you as soon as possible:...

This is a LCD cover for Creality Ender V2. It is very simple design. ...If you are not sure about your bed leveling setting, I would recommend you to use Brim while printing.

Unitl I found this model: https://www.thingiverse.com/thing:2552992 I liked the idea of this mount and changed it so it would fit on the rails of my Ender 3 V2. This is my first model ever edited/created, so every feedback is welcome. I put 2...

Video tutorial: https://youtu.be/FJQs_uMFI8M This is the handle I made as an upgrade to my Ender 3. It is designed to be mounted with silicone leveling columns. If mounted with the springs, remember to put a washer at the base for stability. Don't...

The fan bulge protrudes 8mm below the power supply, and your Ender 3 v2 has 12mm of under-side space available. This makes it a tight fit with just 4mm of space for air to travel through. After careful consideration, I positioned my fan to blow air...

This is a simple print station for an Ender 3 V2, it uses pieces of window wiper to clean the nozzle in 3 directions. To use: Cut 3 sections of window wiper or other heat resistant material into 10mm x 20mm pieces and hot glue them into the holes. ... ...

... knife/scraper thing. Mine simply has a flat plastic piece that attaches to the blade, so I widened and deepened the slot and removed the curve from the original design. In the end the tool holder fits all the tools that came with my Ender 3 v2.

#### RIBBON CABLE MAY BE TOO SHORT TO BE USEABLE #### #### Very Close to Y-AXIS #### This is a screen mount I designed for the Ender-3 V2. I wanted to be able to adjust the angle of the screen to be seen more directly to where I work from. The mount...

This filament guide is for the Ender 3 v2, and slides over the existing metal spool holder bracket. I found one like this on Thingiverse that worked pretty good except it didn't have any support at the base to keep it level, so it kept angling...

This is a (to the best of my abilities) a complete model of the Creality Ender 3 V2, that can be downloaded and edited. The goal of which to allow a user to design parts and test for the physical machine. To my knowledge all of the parts should be...