ender 3 v2 cooling fan upgrade 3d models

I recently bought an Ender 3 v2 printer as a second printer and did not plan to do any medications. Unfortunately, the cooling performance when printing PLA was less than optimal. This might be something specific to my printer. I decided to design...

I recently bought an Ender 3 v2 printer as a second printer and did not plan to do any medications. Unfortunately, the cooling performance when printing PLA was less than optimal. This might be something specific to my printer. I decided to design a...

Summary: Does not require any supports to print Clips into place without fixings - Clips onto the ender 3v2 carriage - check your carriage has the rectangular hole below the left wheel (as you look at it) Only uses the fan screws to hold the fans in...

If you are replacing the mainboard and the PSU fan on Ender 3 v2, I recommend these: PSU cover 92mm: https://www.thingiverse.com/thing:4662559 PSU terminal cover: https://www.thingiverse.com/thing:4774312 Cable guard (goes between the MB and PSU):...

This is a custom 60mm cooling fan mount designed specifically for the Y-stepper motor on an Ender 3 printer. The stepper has been running extremely hot since I installed it with a special printed mount in the dumper, but this new design has resolved...

The latest revision of my CAIMEO Fan Duct for the Ender 3 is now live. This upgrade takes a significant leap forward with several key improvements over its predecessor. The most notable change is the relocation of the fan to the rear, allowing for...

As a result, only one of the two screw holes on E3D's fan shroud will line up with the holes on the Ender-3 V2's X carriage.I added an extra screw hole in the model, which aligns with the hole on the Ender-3 V2's X carriage. ...The mounting screw for...

I required an effective means of mounting the standard part cooling fan following the upgrade of the hotend extruder fan duct to this: https://www.thingiverse.com/thing:2160958. This new setup offers significantly increased visibility and is...

Human-friendly materials like PLA work perfectly for the Creality Ender 2 printer. ...Printing with PLA is easy and straightforward - just let it go without any support structures.

Hello, after a difficult job, I present the first Mistral Fan mod for Ender 3 V2! ... Very easy to install especially if you use my ratchet screwdriver ;-) https://www.thingiverse.com/thing:4853538 Plug ang play No modifications Recommended abs 20%...

It allows a 120mm fan to be installed in replacement of the small noisy stock fan. I am using a Cooler Master Pro 120. It has RGB LEDs I then tied into the string already mounted on my printer for extra cool factor! I printed at medium speed with...

Fan mount for Ender 3 V2 (for printer with NO BL-touch). It is designed for a 60x60 mm PC fan (12v). I used: 4 - M4x30mm (cross type), 2 - M3x20mm (Hex type). The print is made with no support but i used a brim to fix it better to plate. For...

This is the modified mount for the VORON Switchwire to mount it to a stock Ender 3 v2 (no need for linear rail). Some parts need support to print (2 parts of mounting), other parts don't need support. You can see the step file to know how to assemble...

This is a TinkerCAD remix for use on Ender3 V2to reduce noise and maximize air flow:bigger intake fan opening with chamfered edgestill no fan guard (not a good choice, if you have pets or young children)more exhaust side portsrelocated mounting holes...

A Customized 60mm Ender 3 Duct with BLTouch and Light Mounts. The duct has been remixed to accommodate mounts for both the BLTouch and lights, adding functionality to your 3D printing setup. The BLTouch mount is strategically positioned on the...

A version two at the request of some people because of the position of auitolev The photo is from the first version

Ender 3 V2 motherboard cooling with computer 80x25mm DV12C silent cooler and DSN-1504 step-down circuit. (24V to 12V) The DSN-1504 size: 22.5x16.9mm. This circuit is able: IN: 4.5-28V - OUT: 0,8-20V There is a small potentiometer on it, don't...

I found those really nice designed and remixed PSU Covers for the Ender 3 V2. The original design used a 92mm Noctua A9x14 Fan which was just screwed into the cover, the remix I am referencing added a cable guide and a fan holder but uses a 80x10mm...

Dazu müsst ihr jetzt allerdings wissen unter welchem Profil ihr euren V2 in Cura angelegt habt. (Da es beim einrichten des Druckers in Cura kein fertiges V2 Profil gibt nutzen viele das Ender 3 oder Ender 3 Pro Profil.) Ich habe meinen zum Beispiel...

(Da es beim einrichten des Druckers in Cura kein fertiges V2 Profil gibt nutzen viele das Ender 3 oder Ender 3 Pro Profil.) Ich habe meinen zum Beispiel als Ender 3 Pro angelegt und später in Cura umbenannt in Ender 3 V2. (Bild 4) Wenn Ihr nun...

...... It also work for Ender 3 / Ender 3 Pro / any printer that use PC4-M6 The reason why I made this remix is because I own bad quality filament. Thus the "Insert part" always cracked (four times!) even though I already made it bigger than the original.

Ender 3 V2 Satsana Grills U P D A T E: ALL NEW GRILLS FOUND HERE-> https://www.thingiverse.com/thing:5259880/files These grills have a tab that slides into the gap above front fan. This fits perfectly for my build, but you may want to make the tab...

## Ender 3 V2 Quiet Fan Shroud/Cover Much quieter, good airflow, easy to remove. Instructions: - Buy four Orion OD4010-24LB 24V fans. - Use one to replace the fan in your electronics housing - Print this file. Orient it like the photo attached and...

I just got a Ender 3 Max and the fan on the motherboard cover sounded like a Jet Engine. I copied it and replaced the fan with an 80mm silent fan. I also replaced the power supply fan with a 120mm fan so now the ONLY thing I hear is the extruder...

This is a 120mm fan mount I have designed from scratch for a 120mm fan (Specifically I had Corsair SP series 120mm PWM fans laying around). PRINTING DETAILS:When printing, make sure to combine “Fan filter infill.3mf” and “Fan filter frame.3mf”...

Because the others that are similar here generate "screech" noise when the filament passes and also generate dust from the filament that rubs against the extruder entrance and everything is dirty, all this was corrected for the ender 3 v2. This...

Because the others that are similar here generate "screech" noise when the filament passes and also generate dust from the filament that rubs against the extruder entrance and everything is dirty, all this was corrected for the ender 3 v2. This...

The accessory is specifically designed for the Ender 3 and comparable models, attaching securely to the side of the standard extruder casing. ...Several similar designs are already available on Thingiverse, but this one raises the fan a notch higher,...

I found those really nice designed and remixed PSU Covers for the Ender 3 V2. The original design used a 92mm Noctua A9x14 Fan which was just screwed into the cover, the remix I am referencing added a cable guide and a fan holder but uses a 80x10mm...

This remix adds a clip to hang it off the fan casing. Print with no support, added a custom support for the clip. ...Cut off the support part with a knife or cutter after.