ender 3 v2 camera mount 3d models

a snap on camera holder for the Ender 3 V2, good for standard cameras that fit screen tops.

Fits Ender 3 v2, moves with z axis

I remixed this from Adeema's camera mount for the Ender 3. That mount worked great but I installed a CR Touch and it was just barely too thick, causing the x axis to grind when trying to home. This one fits in on the side of the case on left side of...

I remixed this from Adeema's camera mount for the Ender 3. That mount worked great but I installed a CR Touch and it was just barely too thick, causing the x axis to grind when trying to home. This one fits in on the side of the case on left side of...

I needed a camera mount for my Raspberry Pi with built-in camera that would be running Octoprint. I tried various designs that were all good but I needed something simple and easy to put together. I designed this snap together ball and socket system...

ender 3 v2 clip-on camera mount for ir/daylight camera

X-axis webcam mount for sony lifecam webcam on Ender 3 V2. ...Mounts with stock hardware.

I found the sockets on the arms of this mount very quickly lost their grip, so I remixed it to add a slot and a hole for tightening with an M3 x 12mm (slightly shorter would probably work) nut+bolt. ...Still not perfect, but better than it was.

This arm is designed to mount an arduCam at the very front of the bed of an Ender 3 v2 neo replacing the XY tensioner altogether. There are cutouts to allow for tightening the belts. I designed this in Shapr3D measuring the older tensioner using...

20% infill

IP Camera support for Ender 3 v2 printer. ... I have also attached the OpenSCAD file if you need to fine tune it for your camera

Here is a camera mount for webcam or gopro style lightweight camera that attaches to the front of a Creality Ender 3 V2 printer. The bracket attaches using the two threaded holes, at the end of the 40x40 extrusion, used for the bed belt tension...

I wanted a way to attach a USB camera to my Ender 3 V2 that would not require screws. The unit simply hangs off the lower left rail. ...It could be remixed to raise maybe a bit higher.

a simple camera remote holder for use in timelapse videos that i made to attach to Ender 3 V2 using existing hardware screws. ... used a cheap blue tooth camera remote from amazon (link below)...

Left/Right camera mount with USB cable channel.

Left/Right camera mount with USB cable channel.

Remixed Two diffrent Cam mounts

## Ender 3 v2 - Raspberry Pi Camera - Module v3 (auto focus - wide angle) Case and Mount This is actually a remix of 2 items: 1. **The mount** - Raspberry Pi Camera V2 Mount for Ender 3 v2 *by crsn00* 2. **The case** - OctoPi and Pi camera holder *by...

Mount for a camera on the end of an Ender 3 v2 X-axis arm. You can mount it either right side up, or inverted so your camera can be closer to the print bed. I edited the original model to use a camera screw to attach it vs. the webcam-specific hinge...

Mount for a camera on the end of an Ender 3 v2 X-axis arm. You can mount it either right side up, or inverted so your camera can be closer to the print bed. I edited the original model to use a camera screw to attach it vs. the webcam-specific hinge...

First upload :) Adjustable camera mount for Ender 3 V2. Slides over Y-Axis tension adjustment for easy removal. Needs 2 M6 bolts with hex nuts. Hex nuts inset into assemblies. Part 4 holds the camera and allows for slight left and right rotation....

Camera mount to attach a Wyze camera to your Ender 3 S1. It's still a WIP as it'll require a dab of hot glue to actually hold on to the printer. Prints easily on my Ender 3 S1, just have to flip the model 180* so it'll sit flat. ...No supports or...

I lengthened the mounting rod and changed the holder to work with the V2 Raspberry Pi camera. ... I also modified the [Twist in Cable Holder](https://www.thingiverse.com/thing:2816969) to work with the Raspberry Pi camera ribbon cable.

This is a moving camera mount for ender 3v2 neo. I created this to add a wifi camera to my setup to monitor prints. Print this in a lower layer height to make sure the quality it there for it to slot together. The end of the pin did break off for...

This will fit a Adesso webcam, and possibly Logitech as well. ...Mounts to the Z-Axis and aligns perfectly to see the nozzle throughout the entire print. ...Mounts using friction to the Z-Axis cover.

This will fit a Adesso webcam, and possibly Logitech as well. ...Mounts to the Z-Axis and aligns perfectly to see the nozzle throughout the entire print. ...Mounts using friction to the Z-Axis cover.

This is a v2 of a remix I made, which should hopefully solve the potential problems of space, bl-touch compatibility, and different mounting situations for the raspberry pi. The old design had the chain running forward, which increases the space the...

[YouTube Octolapse Test Using My Setup](https://www.youtube.com/watch?v=HvmzqcHGDAc) [YouTube Octolapse of my Le Creuset Pot Lid Holder](https://www.youtube.com/watch?v=f0UMwe8d5Cg) [My Le Creuset Pot Lid Holder - small and...

you will need 4 screws to fit this onto your Ender 3 / 3m - 40mm I just used Home Depot socket cap screws. use at least 4 walls to make it sturdy a big thanks to Slajs for uploading a .step file for me to work with! I remixed his mount for...