ender 3 v2 calibration 3d models

This is a upgrade extruder arm for Voxelab Aquila and Ender 3 (V2) You will need extra hardware to mount the guide wheel as the original one is too short. It will fit the original spring. I have done a lot of prints since this upgrade and still...

Hi everyone, I wanted display on my Ender 3 V2 on the left side and because I didn't found any good I decided to design my own. It's easy to print. Display is in 45° tilt and for mounting I used screws from the original one. ... If you have any...

... the way, so I made this. ...It is mountable on the Ender 3 V2, and I'm not sure about the pro. Definitely not the original, though. It is made for the raspberry pi 4b. ...Thanks to https://www.thingiverse.com/thing:4665097/ for making this originally!

... contribution. ...:) I made a IKEA (Type: L1324, 21777) LED-holder for Ender 3 v2 that slides nicely in to the V-frame. Brims was necessary or else it popped of from the bed. ... If anyone has tips and trix to make it better, please let me know.

Remixed version of the double led strip for the Creality Ender 3. Used this on my V2. Made the distance between the led strips a bit bigger to better spread the light on the print surface. ... Used the following led strip: ...

My PS Eye mount for Ender 3 v2. There is no need for screws. It slides right to the main 4040 profile of the base and the camera goes on the top of the mount. ...The camera base should slide right into the top of the mount and happily sit there.

Screen wire protect, use with ENDER 3 V2 LH SCREEN MOUNT_REMIX (https://cults3d.com/fr/mod%C3%A8le-3d/outil/ahuczekdesign-32ca). You have STL and Fusion360 file. You can change parameter in Fusion360 to change anything. Print face to bed, and use...

I needed a dual Z bracket for my Ender 3 V2, but without the need of extra hardware for mounting it. The only extra hardware needed is the nut for the leadscrew. ... The model is oriented so it does not need supports.

This is a remix of the OEM Ender 3 V2 mount for the EZALE Pro large sensor from TH3DStudio. With my machine the original version of the mount covered the adjustment screw making it difficult to adjust easily. ... This version creates a recess for the...

Hello, after a difficult job, I present the first Mistral Fan mod for Ender 3 V2! ... Very easy to install especially if you use my ratchet screwdriver ;-) https://www.thingiverse.com/thing:4853538 Plug ang play No modifications Recommended abs 20%...

My Ender 3 V2 Mother board is on the top layer so the fan was at the botton with little to no air flow so I made a duel fan holder to mount on the side using the 20x40 extrusion as support

The title says it all! ... This is a mount I designed to hold a Wyze Cam V3 on an Ender 3 V2 to view the bed as the printer is running. ... The design uses 2 M4x8 bolts and 2 t-nuts to screw the mount into the side 4040 extrusion.

... Used the Cable Chain Management from here. ...Cudo's for this. https://www.thingiverse.com/thing:4794723 Used the Cable Management from here. Cudo's for this! Perfect and Complete Cable Chain Management Setup For Your Ender 3 V2.

Just a replica of the Ender 3 V2 NEO hotend bracket I made to make custom fan ducts easier to design, dimensions may not be 100% accurate but is a good starting point when designing a fan duct or any other mod for the toolhead.

Filament Spool Holder Extension for Ender 3 v2. You need four T-nuts and four M4 screws (I used DIN 7984 (lowhead), but You can use DIN912 as well). Also You need two threaded inserts for ultrasonic/thermal installation (e.g. ...Bossard 1052 M4).</p>

Some Ender 3 v2 printers have a slight offset on the z-axis. These spacers work for me. Feel free to remix. STEP file is there. Made this as a quick print. Just use a lot of bottom layers. Some might not need the vertical spacer. ...

Mounts to the M3 holes on the Ender 3 V2 X-carriage, with the same probe offset as the classic mount by Jkostenov. Fits with the stock fan duct as well as the Mini-Me V4. Probe offset: X-42.00 Y-10.00 Thanks to Jkostenov for creating the original,...

This cable chain mount screws into the Ender 3 V2 frame with M3 bolts. I designed it to be compatible with the common V-slot covers and also to be more in line with where the cables connect. ...Make sure to print it with the square part flat on the...

These are direct drive mounts for Ender 3 V2. These mounts are for the default hot end. One is for the default single gear extruder and the other is for the dual gear extruder. ... To install, remove the spacers of the rollers, then fix the mount...

I moved some of the holes to better fit my Ender 3 V2, and cleaned up some of the mesh. ...This should fit the Stealthburner as of commit aabd953 Updated Jan 9 2022 to fix hole location Stealthburner link: ...

Ender 3 V2 better Motherboard Case This motherboard case has a sliding lid that is on the top of it, in this case there is enough room to fit the motherboard and two buck converters for noctua fans or anything if there is anything to update on the...

This is a Support for my Wyze cam v2. ... I made a support for Ender 3 s1 printer and a cage for the cam. I just glued them together. there's also all the files to edit them in case you want to. ...

With these parts you can install any 120mm Fan over your Creality Ender 3 v2 PSU and any 60mm Fan over your Mainboard. ...Fans will be mounted outside of Chassis, so you will need to print 4 of the included 30mm feet.

Fast print for easier turning of the factory extruder wheel for the Ender 3 V2. Designed with blender. Snug fit for the recesses of the wheel without additional fixings. The head of the crank has a recess for quick turning with the fingertip. ...

I really liked the big rollers for the Ender 3 V2 filament guide, but I needed a more flexible setup where my spool holder could be mounted on the side of the printer, needing a double roller setup. ... (Use the bearing guide/rollers from the original...

A direct drive mount for Ender 3 V2 with adjustable X and Y axis. Made it adjustable for my dual gear extruder and possibly for other upgrades. ... Important note: make sure that X end stop is triggered, if not, add some spacer or bend the metal...

I made some modifications to be able to adapt it to the ender 3 pro and v2 or other bed with the same chassis. ... I strongly advise to print the model with a resin printer,the model requires a lot of details in the teeth.

If you have the Ender 3 v2 Adjustable Screen Holder or the remix, and your screen is loose, you don't have to reprint the entire thing again. Print 2 of these wedges and install then on the screen posts, behind the adjustable screen holder. ...If it...

Made some slight adjustments to the hole placement to allow fitment onto the Ender 3 Pro V2 as the mounting plate is slightly different. I filled in the screw access hole that was on the front too. ... Simple screw into the bottom left (as...

Case to mount a 16x2 LCD on an Ender 3 V2 I use it in conjunction with the LCD1602 I2c display (0.1.0) plugin on my Octoprint server Mounts nice and neat above the factory display Feel free to use/ modify