ender 3 v2 bed size 3d models

REMIXED FROM PREVIOUS DESIGNS BY FONSWERKS & MDAVYDIV: 35mm total height, will raise printer by 25mm when installed with rubber feet on Ender 3 models. Suggest printing on flat face. .20mm layer height should be max, designed for .4mm nozzle, no...

This is AirMachine a Ender 3 V2 fan duct for x2 5015. The Idea behind this duct isn't only to provide lot of cooling but to make working at nozzle easier, you can remove the face and have free access to heatsink, etc. Another point is that once...

This is AirMachine a Ender 3 V2 fan duct for x2 5015. The Idea behind this duct isn't only to provide lot of cooling but to make working at nozzle easier, you can remove the face and have free access to heatsink, etc. Another point is that once you...

27/09/2020 Designed to fit the Rasp Pi 4 and display for Ender 3 V2 It will fit the lower versions of pi also. Print Settings Bottom: just print flat and will print fine Top: print upright with supports from build plate Cap: print flat 100% infill...

27/09/2020 # Designed to fit the Rasp Pi 4 and display for Ender 3 V2 I believe it will fit the other versions of pi also. # Print Settings - Bottom: build plate supports no raft just print flat and will print fine - Top: print upright at a...

27/09/2020 Designed to fit the Rasp Pi 4 and display for Ender 3 V2 It will fit the lower versions of pi also. Print Settings Bottom: just print flat and will print fine Top: print upright with supports from build plate Cap: print flat 100% infill...

Fix for a broken extruderarm on the Ender V2. Did a completely new part, since the measurements for the Ender3 replacements seem to be different. Added extra material in the high stress areas to counter any crack formation. This requires the...

This bed pull fits the Ender 3 only (no Ender 3 Pro or V2). I remixed this pull from one designed for the Ender 3 Pro. All you have to do is snap it on to the left side bed roller spacers. It sticks out just enough for you to grab. This is my...

Tete Ender 3V2 pour utilisé deux noctua PWM 40X40, s adapte avec le souffleur d origine

Füße für den / Feet for Ender 3v2 und alle anderen / and other 4040 V-Slot Profile

... so desire. This should work on the 3 & 3 pro, but I think the rubber pads aren't as thick. You might need to shave town the top edge or lose the dampening of the stock rubber pads. ... Fusion 360 files included, I don't care if you hack it up.

This is a redesign from https://www.thingiverse.com/thing:4603075 I've uploades two versions: one with Ender logo and one blank Printed with PETG without Support.

It is possible to get the whole setup on one print if you'd like to do it that way.Tool holder left and right with a left filament wheel or tools designed to fit all original ender tools plus some nozzles.Top main layout for direct drive (Creality...

It is possible to get the whole setup on one print if you'd like to do it that way.Tool holder left and right with a left filament wheel or tools designed to fit all original ender tools plus some nozzles.Top main layout for direct drive (Creality...

Top filament sensor all push fit with gap at back for wiring, made from micro roller lever switch KW12-3 and 608zz bearing. See picture for wiring to sensor (pin 1 and 2 on the board) (outer pins for the switch) Top filament cutter with a drawer...

... When you have printed it you just relevel the bed with the part under the z endstop If you already have your bed level perfect and you don’t want to start over you can just fill it down so it fits. This isn’t some fancy model but et helps a lot.

Recomended print with Layers: 3 Infil: 20% Filament: ABS or PETG No need supports

https://www.thingiverse.com/thing:3235018 is the go to for bed leveling an Ender 3/V2/Pro; however, due to the larger bed side of the Ender 3 Max I found the supplied files weren't a good match. I have modified them to work with the Ender 3 Max...

I designed these bed leveling wheels with a nylon lock nut insert, for my Ender 3 v2. ... You will need: 8 x M4-0.7mm nylon lock nuts 4 x M4 washers 4 x Printed leveling wheels They have been working great for me.

... the _Dual Z Plate.stl_ out along with the other lead screw and motor if you only want single Z axis. I added a piece of white TPU as the bowden tube. Later I'll probably also add black TPU or actual wire as the bed heater cable and hotend cables.

Removed the things that slide inside the extrusions and moved and widened the holes to fit M5 screws and T nuts. ...I printed 3 of the non remixed pieces and 1 of this for the front left, so you don't have to disassemble too much stuff.

Direct Drive Extruder mount for Eryone ER20 Print Settings: 4 to 5 Walls 4 Top 4 Bottom 20 % infill Extra part needed will be longer stepper motor cable like this...

Here you have the calibration test for the Ender 3. ...Bed -> 220 x 220

Ender 3 Bed Spring Eliminator. ...For precise prints, level your gantry using the provided shims.

I made some modifications to be able to adapt it to the ender 3 pro and v2 or other bed with the same chassis. ... I strongly advise to print the model with a resin printer,the model requires a lot of details in the teeth.

... ...This one can also be used to identify over extrusion issues pretty quickly. If the lines are too thin and frail, under, if they are blobby and gooey, over. It's also pretty quick to use a live level print. I use it on both the Ender 5 Pro and 3 V2.

Corner tabs that help align glass beds on the heat bed of an ender 3. ...Could work for other bed types as well.

I use for octoprint cam my old S7 and wanted a stiff mound for the Ender 3 V2 printing bed. Thats why I contructed this one. There will still be a little clearance between the s7 and the mount. I cut a rubber band in little pieces and glued it to...

I use for octoprint cam my old S7 and wanted a stiff mound for the Ender 3 V2 printing bed. Thats why I contructed this one. There will still be a little clearance between the s7 and the mount. I cut a rubber band in little pieces and glued it...

A bed level test sized for the ender 3 bed. Dots are designed to line up approx. with the leveling screws. ...Each dot is large enough to make the leveling and spacing obvious without wasting filament in between the leveling screws.