ender 3 v2 base wobble 3d models

If you have the Ender 3 v2 Adjustable Screen Holder or the remix, and your screen is loose, you don't have to reprint the entire thing again. Print 2 of these wedges and install then on the screen posts, behind the adjustable screen holder. ...If it...

Case to mount a 16x2 LCD on an Ender 3 V2 I use it in conjunction with the LCD1602 I2c display (0.1.0) plugin on my Octoprint server Mounts nice and neat above the factory display Feel free to use/ modify

If you have direct drive and the extruder stepper space is empty, you can use this as a cable guide on your Ender 3 (v2). ... If your printer is inside an enclosure i advise to use heat resistant filaments like: ABS/ASA/PETG

Hello, after a difficult job, I present the first Mistral Fan mod for Ender 3 V2! ... Very easy to install especially if you use my ratchet screwdriver ;-) https://www.thingiverse.com/thing:4853538 Plug ang play No modifications Recommended abs 20%...

This is a simple bed levelling design. ...The Gcode included is for the ender 3 v2 bed size. stl is included so you can change the size to your bed. Its one layer high at .2 resolution. takes about 5 min. ...Enjoy!

Mounts to the M3 holes on the Ender 3 V2 X-carriage, with the same probe offset as the classic mount by Jkostenov. Fits with the stock fan duct as well as the Mini-Me V4. Probe offset: X-42.00 Y-10.00 Thanks to Jkostenov for creating the original,...

... Used the Cable Chain Management from here. ...Cudo's for this. https://www.thingiverse.com/thing:4794723 Used the Cable Management from here. Cudo's for this! Perfect and Complete Cable Chain Management Setup For Your Ender 3 V2.

This is a bracket for use when upgrading a Creality Ender 3 V2 Neo with a Titan direct drive kit. ...The bracket will attach to the two offset holes on the x axis motion assembly and will hold the CR-Touch device as well as the accelerometer that comes...

This is a tool drawer for the 40x40 aluminium extrusion used on Ender 3 V2. Just remove the end cap and pop the drawer in. There is room for ten nozzles, nozzle cleaning tool, nozzle swap wrench and all the Allen keys that came with the printer. ...On...

Updated the mounting section with a boolean cut to accomodate the z-screw brass mount, which on the Ender 3 V2 is protruding of about 1mm. Also gave slightly more room for the z-screw itself. ... Added a second design, without the z-screw protection,...

... the way, so I made this. ...It is mountable on the Ender 3 V2, and I'm not sure about the pro. Definitely not the original, though. It is made for the raspberry pi 4b. ...Thanks to https://www.thingiverse.com/thing:4665097/ for making this originally!

Filament Spool Holder Extension for Ender 3 v2. You need four T-nuts and four M4 screws (I used DIN 7984 (lowhead), but You can use DIN912 as well). Also You need two threaded inserts for ultrasonic/thermal installation (e.g. ...Bossard 1052 M4).</p>

I moved some of the holes to better fit my Ender 3 V2, and cleaned up some of the mesh. ...This should fit the Stealthburner as of commit aabd953 Updated Jan 9 2022 to fix hole location Stealthburner link: ...

Screen Mount for Ender 3 V2 This one-piece print is easily printed and assembled with just an M4 nut and flatheaded bolt. it bring the screen closer to the printer. So you have the same width with or without the screen, whilst still being able to use...

... mounted with 2x M4x10. I tapped thread into the plastic slide using a screw before installation. I am using my squashball feet for the Ender 3 V2 so the machine is higher than stock. ... For the feet see https://www.thingiverse.com/thing:4864585

With these parts you can install any 120mm Fan over your Creality Ender 3 v2 PSU and any 60mm Fan over your Mainboard. ...Fans will be mounted outside of Chassis, so you will need to print 4 of the included 30mm feet.

Fits very tightly on the lower 40mmx40mm rails of the Ender 3 v2. Provides a "shelf" to support the wires and gives you something to tie wrap to. STL file contains left and right facing brackets. ... Print both or delete the one you don't need in...

Ender 3 v2 spool holder with bearings, fully printable. also has a removable stop at the end to prevent spool from accidently falling off the spool holder. Need to manually free bearing and apply lubrication if desired. ...I added a Spacer that is not...

This very simple clamp slips over the spool holder that comes with the Creality Ender 3 Neo V2 to prevent the spool from sliding off. Leaves just a little space between the end of the spool and the filament to allow the spool to spin. ... Inside...

This holder fits the side slots of an Ender 3 V2 Neo. It may fit other models, but I can't guarantee it. It holds the DORHEA 2PCS 24.4inch Micro SD to SD Card Extension Adapter. It may fit others as well. 2 vertical ridges within the cavity hold the...

... en este, se mantienen dos ductos de salida y se puede usar con el cr touch instalado. ...Print Settings Printer Brand: Creality Printer: Ender-3 V2 Neo Resolution: 0.32 Infill: 10 Filament: no pla, petg Post-Printing Category: 3D Printer Accessories

a simple camera remote holder for use in timelapse videos that i made to attach to Ender 3 V2 using existing hardware screws. ... used a cheap blue tooth camera remote from amazon (link below) ...

to jest rmix z opcją czyścika filamenty żeby nie blokował łożyska link do czyścika https://www.thingiverse.com/thing:3033662 Ustawienia drukowania Marka drukarki : Kreatywność Drukarka : Ender-3 v2 tratwy : NIE Obsługuje : Nie ma znaczenia...

Some Ender 3 v2 printers have a slight offset on the z-axis. These spacers work for me. Feel free to remix. STEP file is there. Made this as a quick print. Just use a lot of bottom layers. Some might not need the vertical spacer. ...

This is a replacement drawer knob for the Ender 3 v2 drawer. I suggest to print in PETG since it is more flefible and PLA will break when you push it in the hole of the drawer. //edit: Makers stated, that PLA will work without issues, thanks for...

Simple little part to cover the Ender 3 V2's Z screw - the filament passes past it very close and I didn't want filament to be hit by it. ... It fits over the brass bushing and there's little notches for the screws either side.

I wanted to make My Ender 3 v2's z axis double. So i needed a part that hold second Z axis motor. This is the original parts 3D design. ... You can write me if you want to improve the parts.

... but bltouch will be mounted 3mm higher. ... Original worked great with stock Ender 3 v2 hotend, but I replaced it with all-metal one which is slightly shorter for some reason and bltouch probe collided with bed.

A replacement knob for the belt tensioners of the Ender 3 V2. Or just an M4 knob for anything ;) Requires a M4 melting winding brass insert (see image) using a soldering iron. ... You might have to open the hole a bit after inserting the insert...

For designers to make custom print head and other mods for the X carriage assembly on the Ender 3 V2 Neo. Update 2-16-23 3PM PDT: Corrected the position of the upper left V-Wheel, was off by 4mm. Added a missing hole at the top right of center on...