ender 3 tube coupler 3d models

I reworked the original design so it could be mounted on the left side of the Ender 3 printer. Modifications to the main structure: I attached a bracket mount based on the model found at https://www.thingiverse.com/thing:4346750. This addition...

a (remixed) guide for a standard ptfe tube (4mm) that could be inserted from the side

Remix with holder for the bowden tube and cables, made the screw hole tighter and extended the frame to remove wiggle room.

I crafted this solution following frustrating experiences even after upgrading to Capricorn Tubing and an aftermarket push fitting sourced from Amazon. This clamping mechanism securely fastens onto the aftermarket fitting, effectively eliminating any...

I have a Mosaic Palette 2S and an Ender 3 V2 printer. The printer is inside a Creality enclosure with limited space while the Palette is mounted on the outside. There simply is no room for the Palette inside the enclosure. For the Palette to...

I made this support block for the Satsana shoud to stop the bowden tube being moved about at the hotend.It makes sure the tube is held perpendicular to the hot end.Hopefully this will reduce the amount of stress on the retaining clip where the tube...

I encountered difficulties with the original spacer, due to the short tube inside the hot end not aligning properly with the center hole, which had a slight curve. The exact same spacer was used, but with a 1mm deep guiding channel for the tube. To...

I added an M5 Pneumatic Fitting Thread to it, which resolved the issue of instability with the PFTE Tube when used in conjunction with a Dry Box and the Sensor.

MORE TUBE CLIPS Printing Temperature: 233˚C DON'T RUN OVER 245˚C It'll Start Smelling Like Breakfast Bed Temperature: 60˚C Printing Speed: 50 - 60mm/s Fan: ON FULL TILT

Inspiration came from a Marin_Bs bowden coupler clip from Printables, but I upgraded it substantially. - it has an angled thread so it can be tightened with a provided nut (the more you turn the more it will squeeze) - it can be reused many times...

... ...Within the guide itself, a piece of PTFE Bowden tube can be inserted, allowing for seamless extrusion. ...Although this design was created from scratch using Fusion 360, proper credit should be given to the original creator.

... was stuck. ... In the process, I broke my Bowden tube insertion clip. So I needed a new one. It might not be perfect but it fixed my problem. ... The print takes about 10 minutes with a layer height of 0.1mm and costs 0.08m of filament.

This is an adapter designed to fit on top of the filament sensor and allow a capricorn tube to be inserted. I use this to guide filament from my dryer box to the sensor.The sensor has a small screw protruding slightly from the back. ...This grips on the...

I have added connectors to the PTFE tube and cable holder for plugging in fans, requiring two JST-XHP two-pin plugs. Two small holes are included for M2.5 set screws if extra tightening is needed. It should be helpful for anyone seeking a similar...

Remix with angled hole for 4mm Bowden tube (snug fit- no screw needed). Angle needed to give a more direct path of the filament to the hole in the extruder, so less friction. Screw holes removed as they were not needed on my printer. I've...

I got tired of the tubing popping out of the small grommet bracket that came with my Palette 2, so I designed this alternative solution. It simply slides in without needing a clamp. ...To secure it, an M3 socket head cap screw is used to support the...

This is a remix of the Ender 3 Filament Guide PTFE (for upgraded extruder). ...This adds a cable mounting point to the extruder that is not included in the all metal extruder

3. Put Cura in custom mode. 4. Select the filament guide and use the button "Per Object Settings". 5. Select Infill Mesh and enable that setting. 6. The filament guide turns transparent gray. 7. Position the filament guide to overlap part of your...

The CR10/Ender is a popular 3D printer model that benefits from the addition of an Oldham coupler. This upgrade allows for smoother and more precise movement of the X-axis, which can improve print quality and overall performance. ...By installing an...

This is a coupler to connect a 3.17 motor shaft to a propeller shaft. Size 20mm x 13mm x 5mm The hole size is 2mm. ... Shaft groove 3.10mm

IMPORTANT INFO BELLOWAlright this is for the ender 3 v3 ke or ender 3 v3 se.I made this to remove the spool on top of the printer and allow the filament to feed from a dry box or filament dryer this drastically reduces a lot of vibrations of the z...

Design a Fitting System for Connecting 3/4 Inch Dowels To construct a reliable coupler for attaching three-quarters inch dowels, carefully assess the initial blueprint. The intended size of 3/8 inches represents merely the radius of this joint...

This is the 3 coupler in my system counting away from the collector. It fits into a 4" metal pipe on the side facing the air flow and a 4" metal pipe fits into it on the other end. It has a branch coming out for a 2" PVC pipe. This will run down...

... ... Settings ------------------------------------------ bolt_diameter 3 height 15 diameter_top 6.3 outer_diameter 20 diameter_bottom 5 washer_diameter 5.5 pressure_point_thickness 4.5 nut_diameter 6.25 opening_width 2 articulation_thickness 1.5

http://www.thingiverse.com/apps/customizer/run?thing_id=158717 Using the following options: inline_junction_type is a round shape Vault wall thickness is set to 2.0 mm Stress resistance is maxed out at level 1.0 Number of barbs for output connection...

Male and Female Couplers for Johnniewhiskey's Ender 3 Cable Chain. These couplers enable you to connect two male ends together or two female ends together seamlessly. It is essential to note that these connectors utilize their own link covers by...

Description --------------- This is an accessory that allows you to clip the Palette 3's filament tube to the stock Ender 3 V2 extruder using a regular Bowden tube fitting. How to print ---------------- * Infill 100% * No supports How to...

... causing extruder skips at speeds > 8mm/s (volumetric rate > 20mm³/s). 3/8" tubing may work here, but LLDPE likely loves PETG filament too much. ... If you have an MK2.5/MK3, you might find this useful: https://www.thingiverse.com/thing:2959148

Ender 3 V2 + Palette 3 = Tube Clip DescriptionThis is an accessory that allows you to clip the Palette 3's filament tube to the stock Ender 3 V2 extruder using a regular Bowden tube fitting. How to Print100% infillNo SupportsHow to installUnscrew the...

This modified bowden coupler is perfect for connecting two PTFE tubes together, ensuring a secure and reliable connection. ...However, after assembly, the center of the coupler may require a quick drill to ensure that filament flows smoothly through it...