ender 3 to switchwire 3d models

I built an Ender 3 Pro to Switchwire Conversion Rev.2 printer (https://github.com/boubounokefalos/Ender_SW/tree/Rev.2)I have the Fysect S6 main board which didn't fit into the original electronics layout, prompting me to rearrange the configuration...

Instead of using two M5x10 screws you should use two M4x10, which can be reused from the original Z Axis Limit Switch mount (along with the 2 T-nuts).This is a remix of Darkdog's / boubounokefalos Ender 3 Pro TO VORON SwitchWire.PRINTS WITH NO...

A remix of my OpenSCAD Klipper Expander mount for use in the [Ender 3 Pro to Switchwire conversion by boubounokefalos](https://github.com/boubounokefalos/Ender_SW). This adds a mounting wing that mounts on the underside of the Y-Axis 4040 extrusion...

Ender 3 v2 switchwire themed mod.

SKR Mount for Ender 3 Switchwire Conversion: https://github.com/boubounokefalos/Ender_SW

reverse bowden to voron switchwire, specifically to the ender converted to voron switchwire, I couldn't find a corresponding file anywhere, so I created this one. In my case it helped with the zebra on prints. ...

https://github.com/boubounokefalos/Ender_SW/tree/main/STL/Electronics Since I replaced the stock leg extrusions of my Ender 3 Pro with 500mm 4040 extrusions in order to better match the stock Voron Switchwire, I needed a better way to mount the...

A clumsy remix of the rear grill panel for the [Ender 3 Pro Switchwire Conversion by boubounokefalos](https://github.com/boubounokefalos/Ender_SW). ...This version adds three keystone slots to access the ports of the Pi without opening the printer up.

This is a remix of the alternative keybak for Voron Switchwire or Ender 3 to Switchwire conversion. ...With this mod you can use the Voron standard heat inserts (M3x5x4) Cheap door puller as keybak:→ https://www.aliexpress.com/item/100500 Voron size...

... Pico mount for a switchwire conversion. ...When Stacking the Pi onto the Pico you need additional feet for the needed space.Remixed from the SKR Mini E3 mount from boubounokefalos' Ender Switchwire Conversion.https://github.com/boubounokefalos/Ender_SW

This is a modified version the VORON Switchwire fan duct to mount it to a stock Ender 3.I used two 4010 blower fans mounted back to back for cooling the part, and far the heat break it remains the stock 4010 fan.You may find that mounting the blower...

The Ender 3 to Switchwire conversion from DaRk_dOg has an enclosure which has several corner pieces which also serve as light mounts. I didn't have the proper 60 LED/m strips on hand, but I did have two Daybreak Neo Minis I bought for a previous...

This is the switchwire extruder mount modified to accept hermitcrab ( and probably other mgn12 mounted extruder ) . ... The little gap between the mount and the hermit plate is for running the endstop switch wire to do : Add a part for linking it to the...

I wanted a simple driver to my Ender 3, but I have not found it, that I was remixed order and make thin wall with simple holes. It's simple and leight, so you don't need a lot of filaments. ...

A simple mount for 4040 extrusions for RPI zero 2w. ...This was part of ender 3 to switchwire conversion

Created specifically for the Geetech A10 to operate the Ender 3 hotends effectively.

Members are welcoming to share result, ask questions related, and remix the files Ender 3 based to corexy conversion objective to repurpose of everything in ender 3 from screw to electronic. It also objective to be build by only used precut 2020...

After seeing that many people were complaining that this drawer did not fit their simple model ender 3, because it is high and takes the bed screws, I decided to lower the model in 3mm, I also made some openings in the case to save PLA Apó ver que...

... don't come into contact with the metal/ground. https://configurator.reprapfirmware.org/Start My settings are stored in the configF.json file (Ender 3, standard endstop switch xyz, geared extruder, with standard extruder set step per mm to 93).

When you decide to convert Your Ender 3 with this upgrade, you have to change the position of one set of motor wires, because placed like this the direction of the motor must be reversed. This can be 1 and 4 of 3 and 6. The Best is to find the...

Although these designs were top-notch, I wanted something that could be mounted directly onto a linear rail, such as the Mgn12h, without any issues regardless of whether it was on my Ender 3 or not. With this in mind, I decided to take matters into...

This remix is based on Túlio Sathler Siman (@TulioSathlerS_973127) work on printables.I readjusted the dimensions so they would fit tighter on my old Ender 3 Pro (2019) rubber feets (they will not fall if I lift the printer).I also added some insert...

Box case when converting micro sd to sd YOUTUBE introduction link https://youtu.be/mJh8h_s_OWU

Found an Oreo or Benchy knob you want to use on your Ender 3 or Ender 3 Pro but it's made for an Ender 3 V2? Look no further than this simple adapter piece. This adapter can be super glued into place, I personally didn't have any on hand so I just...

I actually preferred the drawer layout, but I couldn't find any remixes that compared a standard Ender-3 to a Pro. So, I created this straightforward rail adapter to enable the upgrade. ... Infill density: 30 percent

Need 2 mgn12H 450 mm 1 mgn9H 350 1 rail 20x20 390mm the rest is standard part from switchwire see step file for bom

Simple camera holder to Ender 3.

shortened ukulele neck to fit ender 3

for ender 3

this is a version of the stormtrooper helmet split to fit in a printer area of 220x220x225 (as a ender 3).