ender 3 support rods 3d models

This is a modification and remix of a fan-style "Fang" support for the Ender 3. The original link below was a Fang designed for the Tevo Tornado v1. I wanted to modify the duct to make it wider so that there would be better air circulation, a larger...

A remix of AJCam44's excellent cable support for Ender 3 S1 Pro. I adapted it to fit the S1 non pro. Also I added support for extra wiring shown in the photos. Should work with PLA but I used PETG. The bottom support bracket is very different from...

Fixed alignment issues for the Ender 3 Pro. ...The fan is offset on the bottom panel and there is a case screw in the way.

Another ingenious solution for holding cables on the Ender 3 printer, a straightforward and uncomplicated design that gets the job done.

Base for the original PLA spool holder of the Ender 3 V2. ... Screws: 5mm x 8 (the same as for the bracket).

The advantages over the original Ender 3 bracket: 1 - Visibility of the print on the plate 2 - Weight saving 20 grs instead of 50 grs for the original 3 - We keep the two fans and screws to reuse them on this assembly. 4 - The blown air comes out...

The fan support is slightly offset towards the front of the printer because depending on the age of the ender 3 the screws of the belt tensioner are not of the same thickness so the support comes forced on it during large printing. The ring was...

This adapter consists of two parts the first was modified to enter better way in the screws of the usillo nut without the need to dismantle a stabilizer that has put my printer (Sensor Mount), and the second is to mount the filament sensor so that...

I suppose most of the parts can be used on other printers with a bit of remix Best regards Eric ######################################################################## Hello everyone, This support is made to use your C270 Logitech directly on Ender...

this is a design to place a webcam on the y-axis of the ender 3 Pro printer with a hole to pass a screw to secure the camera.

The Ender 3 Pro's assembly was tweaked to perfection by adjusting its structural components. ...A misaligned fan had been hindering airflow under the printer's lower panel, while a misplaced case screw blocked access to key parts.

Unitl I found this model: https://www.thingiverse.com/thing:2552992 I liked the idea of this mount and changed it so it would fit on the rails of my Ender 3 V2. This is my first model ever edited/created, so every feedback is welcome. I put 2...

... MIRA LA MEJOR Y NUEVA VERSION DE ESTE SOPORTE:https://www.thingiverse.com/thing:6560092Este es un soporte para colocar la mintion beagle en una ender 3. ...Se coloca en la parte final del eje de la cama, haciendo así unos espectaculares timelapse.

Upgrade Your Bobine for Smooth Rotation and Zero Friction Ensure Perfect Performance on Creality Ender 3 and Ender 3 Pro Models Before Upgrading, Consider the Following Essential Components: - Two precision bearings with an outer diameter of 22 mm...

My Ender printer lacks full support due to a reduced distance of 17mm between the power supply unit and the extruder, whereas the standard model provides 18mm of clearance for the build platform.

This one might interest you if you have an Ender 3 or similar printer, an Apeman A80 Camera or similar, and the bullseye vent upgrade (https://www.thingiverse.com/thing:2759439). I've uploaded the STL file and F3D file for your convenience. Please...

This is a 53.5 mm diameter dial gauge holder for the Ender 3 V2 printer. It sits on top of the extruder fan housing and attaches to the extruder with an M8 x 25 mm screw. The bracket is of the clamp type. ...For the comparator there is a M6 x 60 mm or...

English Designed for: ENDER 3 V2 (could be used for other models if they share the same rail and holes). The model fits to the rear of the right rail, using the holes that come from the factory. Advantage of the model: Does not obstruct...

... inside where you can insert a spring from any ballpoint pen to keep it securely in place. The base fits snugly into the right-hand side of my Ender 3 control panel. ...After attaching the cam, simply slide the ring onto the top side of the pole.

this design is a stand to hang the pliers of the Ender 3 pro printer that comes included in the tool kit of the same this stand I recommend sticking to the desired wall with double-sided tape as this ------>...

I just installed some upgrades on my Ender 3 V2 Basically: - 1 Box and holders for raspberryPi 3B - 1 Box for Lighting Relay, compatible with mauser relay: https://mauser.pt/catalog/product_info.php?cPath=1667_2604_2606&products_id=096-4673 - 1 box...

... print can simply be pushed on and pulled off when leveling is complete. A stylized Ender 3 dragon head is attached to the side for visual appeal. ...The slots on either side align with the fan shroud's ventilation slots, ensuring optimal airflow.

The human plays a crucial role in maintaining the structural integrity of the Z Rod by keeping it properly aligned and stable.

... designed for both models. PS. Add a small adjustable foot with screws to the upper left corner (at the back of the fan) of the power supply (3*8 screw and washer) to prevent tool support from slipping if you regularly move your printer.

Support for LM2596 Buck Converter

Support for LM2596 Buck Converter

Support écran avec les vis d'origine

To install this support post, you will need short M5 fasteners and 3 small cable ties. The top and bottom clasps do not clamp the cables, so they can be moved for final adjustment and trial movement. Once you have made your adjustments, you can use...

Support for GoPro cameras as well as Picam is available.

The human is closely monitored, supported by the ender3 printer. A 20% fill level is maintained. The resolution is set to 0.2mm. ...Support is provided.