ender 3 spool holder 3d models

The inside diameter is 30.5 mm (fits perfectly for Ender 3 Pro spool mount) and the outside diameter is 52 mm. I only printed one-half of the extended one 3 halves of the normal one since it can keep the spool in place. If other dimensions needed...

This bracket is designed for mounting the spool at the rear of an Ender 3. I was inspired by Chuck's design, which this remix is based on, but I wanted to make some modifications. Here are the changes I made: The bracket now extends farther out than...

A tool holder that slides on the original spoolholder that came with my Ender 3 v2. Probably fits Ender 3 and ender 3 pro aswell! Slides on my spoolholder right out of the printer. It holds one of the orignal wrenches that came with the printer,...

A tool holder that slides on the original spoolholder that came with my Ender 3 v2. Probably fits Ender 3 and ender 3 pro aswell! Slides on my spoolholder right out of the printer. It holds one of the orignal wrenches that came with the printer, my...

All you need is 2 x 608ZZ Bearings I printed this in my ender 3 pro, with 0.2 layer height with 7% to 10% infill but that depends on your pattern and the strength you looking for. I printed my nut with 0.3 tolerance, and it gets on it with a litle...

its a spool holder that adapts to the vanila spool holder, but it ofers less resistence on rotation moviments avoiding overloads on the extruder motor

Simple filament spool holder. ...Uses original spool holder and mounts straight to the adapter. ...This is meant to be drilled onto a table.

As a result, I extended the piece out more laterally just enough for clearance which still allows for adequate meshing with another Ender 3 next to it. Uses same mounting hardware found with stock Ender 3. ...Refer to CHEP's video on YT for more info.

... need and generate holder, axel, wheel separately. You can also generate the demo assembly (which of course isn't intended for printing). I have lost my GCODE files for this project unfortunately, but if I re-print I will upload my Ender 3 GCODE.

simple attachment for the original ender spool holder. just unscrew the stock axle, fix the attachment to the metal part ( i just used two zip ties) and screw the m8 bolt with the bearings and spacers on. you need an 80mm m8 bolt (80mm without head),...

Spacer for the filament spool holder. ...Helps keep the spool from moving along the holder and thus more aligned with the extruder. Easy to install. ...Just snap it on!

Spacer for the filament spool holder. ...Helps keep the spool from moving along the holder and thus more aligned with the extruder. Easy to install. ...Just snap it on!

I wanted to make another Base for my spool holder As I use a printed one,  

This is a simple holder to extend the filament spool in 45 degrees, only need 2 M5 nuts because de holder fits in the printer structure ;)

This coil holder for Ender 3 allows the coil to be re-centered on the axis for axis passage diameters up to 75 mm. Three nuts, one screw and two cones are required. ... -Change from 23-05-20: screw extension (+40mm)

I made it for my CR-10 mini, but it will work on the CR-10, Ender 3, or any printer with a top gantry made of 20 by 20 aluminum extrusion. In order to attach it you will need 4 M3 hammer nuts, and 4 M3 X 14 or larger bolts. M3 X 12 may have...

This is a straightforward holder that increases the filament spool angle by 45 degrees, requiring just two M5 nuts since it fits snugly within the printer's framework.

I've observed that some of my spools possess an inside diameter substantial enough to potentially slip off the spool holder, over the stock nut provided with Creality printers. This nut features a flange designed to prevent large diameter spools from...

... prints from this location. ...The main problem is that the spool began to sag forward, then started rubbing against the extruder. This caused it to jam and was simple to load and unload the spool. ...I also added a small hook for the filament holder.

When printing with my Ender 3, I often notice that the Filament holder nut tends to turn and lock itself down on the filament side while extruding, resulting in excessive tension on the Extruder stepper motor and even causing filament skipping. To...

... any excess lubricant from the bearings to ensure they rotate smoothly and applied a new lubricant using oil. Follow the photos for proper assembly. The original spool holder's tube locking ring will fit perfectly onto the newly printed spike holder.

... holder when holding 1 kg filament will tend to bend. So I designed and remixed a part of the thing to support the side spool holder. ... The height may not be perfect but I made it a bit shorter so I can stick some mat under to keep it firm.

I added a foot to support the end so there isn't any pull on the part at the machine, all the weight is being applied to the foot.I test fit this to two different ender 3's and it glides right in. I added a screw hole if you feel you need it but I...

I tightened up the filament spool holder, securing it firmly near the extruder and preventing it from slipping into my X-axis stepper damper. I engineered this setup to be rock-solid, resisting constant vibrations that threatened to loosen the bolts....

both for the 2020 aluminum rails and the 4040 rails print on one side and use supports You'll need a heat insert nut for the one side to properly thread and tighten to existing spool holder ----------------- June 20, 2022 -Added a 2020 vertical mount...

The holder is suitable for spools of filament with a width of 530 mm and an internal diameter of 320 mm. The cover sits tightly, so it is better to remove it from the back side by squeezing out so as not to damage the axis. The design does not...

... spool began to sag forward, causing it to rub against the extruder. This issue held up the printing process, but it was also easy to load and unload the spool whenever needed. ...I also added a small hook to securely hold the filament clip in place.

The mounting system has been upgraded to minimize or eradicate the rotation of the spool arm, resulting in improved stability and reduced wear on its components.

This accessory holds your filament spool at the back of the printer so that it takes less space and is out of the way.

2 printed, 1 8mm shaft (with length: spool width + washer thickness + nut width (height) for mounting), 2 bearings (8 x 22 x 7). The diameter of the spool is 53.5 mm on one side and 52.5 mm on the other, with a 5 mm deep 55 mm shoulder. Infill...