ender 3 spool holder thingiverse 3d models

New version of Spool Holder (https://www.thingiverse.com/thing:3707432). This version can be rotate to have a good filament route. ... What you need : 2 x M3x16 screw 2 x M3 nut 2 x M3 washer 1 x M4x30 screw 1 x M5 nut 1 x M5x30 screw 1 x M5 nut 1 x...

Spacer for the filament spool holder. ...Helps keep the spool from moving along the holder and thus more aligned with the extruder. Easy to install. ...Just snap it on!

Spacer for the filament spool holder. ...Helps keep the spool from moving along the holder and thus more aligned with the extruder. Easy to install. ...Just snap it on!

However, I did manage to break a PLA version due to excessive tightening of the adjuster wing while mounting a spool. You can find individual STL files for each part as well as a complete KIT STL if you prefer to print everything at once. For...

I did manage to break a PLA version but it was due to over tightening of the adjuster wing while mounting a spool. Individual STLs for each part as well as a FULL KIT STL if you want to print it all at once. For PLA use 210 Nozzle Temp - 50 Bed...

Remixed version from Cootajohn. ...Added support to keep the spool in place as an all-in-one bearing loaded holder.

I wanted to make another Base for my spool holder As I use a printed one,  

This is a simple holder to extend the filament spool in 45 degrees, only need 2 M5 nuts because de holder fits in the printer structure ;)

This coil holder for Ender 3 allows the coil to be re-centered on the axis for axis passage diameters up to 75 mm. Three nuts, one screw and two cones are required. ... -Change from 23-05-20: screw extension (+40mm)

I made it for my CR-10 mini, but it will work on the CR-10, Ender 3, or any printer with a top gantry made of 20 by 20 aluminum extrusion. In order to attach it you will need 4 M3 hammer nuts, and 4 M3 X 14 or larger bolts. M3 X 12 may have...

You will need to take the spool holder off to add a spool though. EDIT: made the end part 50mm instead of 56mm. So it's easier to add/remove the roll. Also removed the clip part where the bearing snaps into place; replaced it with two M8 Screws...

... reinforced. Even with 10% infill, the thick shell should provide sufficient strength. Please note that this spool holder may not be compatible with all spools, so it's best to retain the original spool holder for potential use in the future.

I also made it so the stock spool holder couldn't slide out of the slot on the holder. There are 2 nuts or knobs. Its dealers choice, both work with the threads. The nut or knob wants to print with supports, but I just blocked them. The Base...

A specially designed filament spool holder attaches securely to both sides of the support rail, providing enhanced stability and preventing any potential interference with the motor during spool changes by angling itself away from direct alignment.

A straightforward and uncomplicated spool holder designed to accommodate spools up to 100mm in width. ...Unlike other options I encountered, this one avoids unnecessary complexity while minimizing filament usage for a hassle-free printing experience.

Attaches to existing spool holder allowing you to hang 2 spools as well if you wanted to, It pushes though the center of the existing spool holder. It's a snug fit but cannot fall out the other side because of the back stopper. I printed it at...

The spool holder slides on 3 rings to minimize the contact surface and thus minimize friction. However, it is good to put a little layer of grease on it to avoid squeaks and you will see that it will turn even better, as if it had bearings ([watch...

Material does not matter you will need two sets of the screws to hold the spool holder to the top to mount it.

This is a straightforward holder that increases the filament spool angle by 45 degrees, requiring just two M5 nuts since it fits snugly within the printer's framework.

Spool holder for V2, you will need to source: - M3 x 20mm. - M3 x 15mm. - M3 Brass insert (2 needed). ... - 22mm OD/ 8mm ID bearing (6 needed).

This spool holder slides into the v-slots on the base of the printer, handily holding the filament near the extruder. ... Best of luck and happy printing

... prints from this location. ...The main problem is that the spool began to sag forward, then started rubbing against the extruder. This caused it to jam and was simple to load and unload the spool. ...I also added a small hook for the filament holder.

I've observed that some of my spools possess an inside diameter substantial enough to potentially slip off the spool holder, over the stock nut provided with Creality printers. This nut features a flange designed to prevent large diameter spools from...

This clip will fit any 30MM spool holder and minimize spool wobbling. Move it right up to the spool, making sure it's not too tight and doesn't interfere with the spool during printing. Clips on easily, to remove simply push down on the circular...

When printing with my Ender 3, I often notice that the Filament holder nut tends to turn and lock itself down on the filament side while extruding, resulting in excessive tension on the Extruder stepper motor and even causing filament skipping. To...

... any excess lubricant from the bearings to ensure they rotate smoothly and applied a new lubricant using oil. Follow the photos for proper assembly. The original spool holder's tube locking ring will fit perfectly onto the newly printed spike holder.

I wanted a better spool holder design from my direct drive and i saw a s1 spool holder stl and ive remade it so it took less time to print and use less material. this isnt a remix ive done this from scratch using a similar approach to the...

I wanted to use 608zz bearings with the spool holder at https://www.thingiverse.com/thing:2988540, so I edited it in OpenScad. Make sure to use the original file with OpenScad to make changes. To complete the project, you will need the nuts from...

I remixed this from [HUNMU's spool holder design](https://www.thingiverse.com/thing:3081267) while changing the lockup mechanism to [Deian's spool mount](https://www.thingiverse.com/thing:3866438) so I could keep using [LilTrublMakr's front-extrusion...

So, I rummaged through my toolbox and found a nut with threading from ChunkAhoy, then created a custom Spool Holder from scratch, carefully shaping it to have an outer diameter of about 15 millimeters at one end and 10 millimeters at the other. ...It...