ender 3 spool holder size 3d models

I did manage to break a PLA version but it was due to over tightening of the adjuster wing while mounting a spool. Individual STLs for each part as well as a FULL KIT STL if you want to print it all at once. For PLA use 210 Nozzle Temp - 50 Bed...

However, I did manage to break a PLA version due to excessive tightening of the adjuster wing while mounting a spool. You can find individual STL files for each part as well as a complete KIT STL if you prefer to print everything at once. For...

I've got some spools of filament, especially 250g spools - that have a very narrow hole in the middle, too narrow for the spool holder that comes with the printer. I've used various hacks in the past, but wanted something a bit easier and nicer to...

Remixed version from Cootajohn. ...Added support to keep the spool in place as an all-in-one bearing loaded holder.

I wanted to make another Base for my spool holder As I use a printed one,  

This is a simple holder to extend the filament spool in 45 degrees, only need 2 M5 nuts because de holder fits in the printer structure ;)

I've been using this for a few months without issues. Tolerances for my printer when printing threads are built into the STLs - 0.1 on either side of the thread for a total of 0.2. It may work a little too well, the filament tends to unspool a little...

This coil holder for Ender 3 allows the coil to be re-centered on the axis for axis passage diameters up to 75 mm. Three nuts, one screw and two cones are required. ... -Change from 23-05-20: screw extension (+40mm)

... ...I did not want to cut my stock spool shaft so I designed a replacement. No additional hardware needed. Spool inserts are for a spool with a 75MM centre hole. you can change the size to match your spool by changing the parameter in Fusion 360.

I made it for my CR-10 mini, but it will work on the CR-10, Ender 3, or any printer with a top gantry made of 20 by 20 aluminum extrusion. In order to attach it you will need 4 M3 hammer nuts, and 4 M3 X 14 or larger bolts. M3 X 12 may have...

... reinforced. Even with 10% infill, the thick shell should provide sufficient strength. Please note that this spool holder may not be compatible with all spools, so it's best to retain the original spool holder for potential use in the future.

You will need to take the spool holder off to add a spool though. EDIT: made the end part 50mm instead of 56mm. So it's easier to add/remove the roll. Also removed the clip part where the bearing snaps into place; replaced it with two M8 Screws...

A specially designed filament spool holder attaches securely to both sides of the support rail, providing enhanced stability and preventing any potential interference with the motor during spool changes by angling itself away from direct alignment.

A straightforward and uncomplicated spool holder designed to accommodate spools up to 100mm in width. ...Unlike other options I encountered, this one avoids unnecessary complexity while minimizing filament usage for a hassle-free printing experience.

This is a stand I designed specifically for a ball-bearing spool holder, designed by nathansc (https://www.thingiverse.com/thing:3551666).Other spool holders will probably also work with this, but I have not tested this.I designed this because I...

This is a stand I designed specifically for a ball-bearing spool holder, designed by nathansc (https://www.thingiverse.com/thing:3551666).Other spool holders will probably also work with this, but I have not tested this.I designed this because I...

Attaches to existing spool holder allowing you to hang 2 spools as well if you wanted to, It pushes though the center of the existing spool holder. It's a snug fit but cannot fall out the other side because of the back stopper. I printed it at...

This is a straightforward holder that increases the filament spool angle by 45 degrees, requiring just two M5 nuts since it fits snugly within the printer's framework.

This spool holder slides into the v-slots on the base of the printer, handily holding the filament near the extruder. ... Best of luck and happy printing

Spool holder for V2, you will need to source: - M3 x 20mm. - M3 x 15mm. - M3 Brass insert (2 needed). ... - 22mm OD/ 8mm ID bearing (6 needed).

Material does not matter you will need two sets of the screws to hold the spool holder to the top to mount it.

... prints from this location. ...The main problem is that the spool began to sag forward, then started rubbing against the extruder. This caused it to jam and was simple to load and unload the spool. ...I also added a small hook for the filament holder.

I've observed that some of my spools possess an inside diameter substantial enough to potentially slip off the spool holder, over the stock nut provided with Creality printers. This nut features a flange designed to prevent large diameter spools from...

When printing with my Ender 3, I often notice that the Filament holder nut tends to turn and lock itself down on the filament side while extruding, resulting in excessive tension on the Extruder stepper motor and even causing filament skipping. To...

... any excess lubricant from the bearings to ensure they rotate smoothly and applied a new lubricant using oil. Follow the photos for proper assembly. The original spool holder's tube locking ring will fit perfectly onto the newly printed spike holder.

I wanted a better spool holder design from my direct drive and i saw a s1 spool holder stl and ive remade it so it took less time to print and use less material. this isnt a remix ive done this from scratch using a similar approach to the...

... holder when holding 1 kg filament will tend to bend. So I designed and remixed a part of the thing to support the side spool holder. ... The height may not be perfect but I made it a bit shorter so I can stick some mat under to keep it firm.

So, I rummaged through my toolbox and found a nut with threading from ChunkAhoy, then created a custom Spool Holder from scratch, carefully shaping it to have an outer diameter of about 15 millimeters at one end and 10 millimeters at the other. ...It...

This stand was specifically created to hold a ball-bearing spool holder designed by nathansc, who can be found at https://www.thingiverse.com/thing:3551666.\r\n\r\nOther spool holders may also work with this design, but I have not conducted any...

... alignment. 2. Placeholder Wedge: Must be securely fastened with a bolt barrel in place. Print Settings: * Spool holder: 30% infill for added strength and durability * Stand: 10% infill for minimal weight while maintaining structural integrity