ender 3 spacer 3d models

Those are Two little spacers to fit the original Creality Light for Bigger printers on the Ender 3 S1 PLUS. Just Print one of each and you are good to go to screw the light on your printer. ...The light need to be conected dirctly to the 24V Power...

Spacer/Spring Holder for Ender 3, Ender 3 Pro, and Possibly Other Creality Machines Too. 4.8mm Inner Diameter, 12mm Outer Diameter, Spring Cup Diameter is 8.8mm I Needed a More Rigid and High-Quality Bed Spring Spacer to Provide Greater Force to My...

a common improvement to Ender 3 bed leveling is to use stiffer springs, since stiffer springs apply more force to hold the adjusting knobs in the right place.These spacers also increase the spring force, but do so by compressing the existing springs...

X and Y Axis limit switch spacers for the Microswiss DD Extruder on the Ender 3. I made these so I didn't have to deal with editing the home offsets in the firmware. After printing, I glued the X axis block to the side of the microswiss carriage and...

A 2.4mm (can scale it to w/e size you want in your slicer) thick spacer for the ender 3 pro powersupply. 

I took a simple approach to remixing Davidmirv's Ender 3 Z-axis spacers, making some key changes to enhance functionality. The main modification was removing the lip feature that was present in the original design. ...I also made sure to add the spacer...

This is a spacer for using the Creality Ender 3 V2 BLTouch kit with an all metal Micro Swiss hot end. The Micro Swiss sits a bit lower than the standard hot end. ... Z-Offset of -2.08 worked for me on my machine with this spacer.

This is a model to space out the e3d Hemera from the all metal Ender 3 mount that we sell. The spacer is to suit bolts included in the kit. ...Please double check that you're using the correct bolts so you do not over tighten and damage the Hemera...

Made this spacer for my Ender 3 as I was upgrading from the 32-bit board into MKS E3P, the heatsink of the stepper motor driver was intruding the electronic cooling fan, so i made this simple raiser/spacer to accommodate the space needed. You will...

This is a Spacer to raise up the runout sensor if you are using the actual creality runout sensor or bracket spacer raises sensor 8.75 mm so you will need to get some m3 x 25 or 30 screws I found mine m3 x 25 at local Menards the actual Dimensions of...

... ... The extended fan duct makes sure that the part cooling fan is blowing directly below the hot end. Super fast and easy to print. No supports needed. I recommend using 2 M3x16 bolts for the spacers, and I used 4 M3x6 bolts for the fan. ...

When installing the BL touch there is insufficient head room in the compartment for the main board, thus this thing is a spacer which increases the head room of the compartment. ...Also after prolonged used the SD card slot may fail to remain in place,...

This is a bed spacer for the Ender 3 Pro. ...It can go either under or above the original part named CableChain_BedCorner_V2

The spacers used on the Ender 3 are typically pretty standard, but this particular option is designed to match the exact specifications of the stock mount provided by the manufacturer. ...This spacer could potentially offer some advantages over the one...

The Ender 3 Pro BLV dual Z upgrade kit from Aliexpress appears to be missing crucial components (a single spacer, for instance). To rectify this issue, I created a custom replacement spacer.\r\n\r\nNotably, the seller has now acknowledged these...

This is a 10mm spacer designed specifically for use with the Ender 3 spool holder, boasting a 34mm inner diameter that fits perfectly over the holder. I created it in conjunction with the spool inserts by KenLaires, which can be found here:...

Adjustment spacer for the x-axis pulley wheel on the Ender 3 Pro. Instead of removing the press fit pulley which is not straightforward, this can be used to more easily align the belt. You need to z-cut it to the size you need. ... The big...

Adjustment spacer for the x-axis pulley wheel on the Ender 3 Pro. Instead of removing the press fit pulley which is not straightforward, this can be used to more easily align the belt. You need to z-cut it to the size you need. ... The big version can...

This spacer is specifically designed for the Ender 3 Pro and has only been verified to work seamlessly with the damper shown above. To function properly, a modification of the printer is required, but this modification can all be reversed if needed....

Hello !That's my first project - I know is simple but works well.It's spool sleeve flanger spacer for Ender 3 and others with spool holder diameter about 32 mm (I have 31,7 mm) and spool hole inner diameter about 53 mm (I have 52,8 mm).It helps spool...

We recently installed an Ender 3 V2 in our off-road camper and with space being at a premium, I tried to make it as compact as possible. I was planning to simply remove the display and use Octoprint and gcode terminal commands. But then I noticed...

We recently installed an Ender 3 V2 in our off-road camper and with space being at a premium, I tried to make it as compact as possible. I was planning to simply remove the display and use Octoprint and gcode terminal commands. But then I noticed...

Instead of using washers I designed a 3mm spacer to go behind the backing plate.

just a spacer required to assembly hunterius_prime's dual z carriage

I needed to space out the Phaetus BMS hotend a bit on the Ender 3, so the silicon sock would be able to fit onto heatblock while still clearing the bottom wheel mount on the X gantry carriage. This part slips over the hotend standoff mounts. I...

I have an Ender 3 V2 and used the 45° spool holder by @ZTolerance (https://www.thingiverse.com/thing:3446507). Didn't read the description properly and just mounted it with the screw that was already in the frame (for the Ender 3 V2 at least this is...

"Remix" to include different thickness .stl files. Print Settings Printer Brand: Creality Printer: Ender 3 Pro Rafts: No Supports: No Resolution: 0.16 Infill: 100% Filament: Generic PLA Any Post-Printing ============= Mount instructions (same as...

I needed to space out the Phaetus BMS hotend a bit on the Ender 3, so the silicon sock would be able to fit onto heatblock while still clearing the bottom wheel mount on the X gantry carriage. This part slips over the hotend standoff mounts. I...

This is a spacer that prevents the filament from touching the greasy z-axis screw. ... It requires a minimal amount of plastic and can be fitted without any additional screws.

I designed this spacer to offset the probe slightly to compensate for the extra nozzle length. The spacer is 2mm thick which will work with the screws that come with the CRTouch but can be made thicker. ...I've included the Inventor file and a step file...