ender 3 silent fans 3d models

Widened the fan hole as it was narrower than the fan and noisy, and removed the grille to reduce noise. Works with any 6015 fan, with simple replace. Result: minus 3db compared to the one I remixed. Original bolts works fine without...

> I did a new version ( Mobo Cover v4.stl ) so the fan can be mounted underneath and isn't limited to being 14mm thick. It now prints much faster, without supports and has a grille to stop wires dropping into the fan. Be very careful when removing...

Liked the remix, but wanted more protection for the fan so I added a "fan guard" structure. Prints with the structure laying flat on the printbed. I had no Issues with clearance between the fan. The mounting holes don't line up perfectly but it's...

Liked the remix, but wanted more protection for the fan so I added a "fan guard" structure. Prints with the structure laying flat on the printbed. I had no Issues with clearance between the fan. The mounting holes don't line up perfectly but it's...

Fits a Noctua A9-14 (4pin) 12v fan - 92x92x14mm Original PSU fan had a 74dB peak noise level (as measured with my potato) After the mod the psu peak noise is 51dB (measured with the same potato). Support: YES. (there's a small piece in the corner...

... small mosfet. Note: Just like the remix, you can still use M3 screw to tighten it onto the slot. It should line up to the same thing. Fan size: (92x14mm) Noctua A9x14 https://www.amazon.com/Noctua-NF-A9x14-Premium-Quiet-92x14mm/dp/B009NQM7V2

You do need to remove the PSU cover to allow the fan to do its work and, as usual with Noctua fans, you'll need buck converters to drop the 24v source to the 12v that the fans require. I left the 4020 PSU fan connected to act as a warning. It will...

This way the fan only spins when the power supply needs it to.Printer: Creality Ender 3 MAXFilament: OVERTURE PLAInfill: 100%Support: NOAdhesion: As you wishNozzle: 0.4mmQuality: CURA adaptive layersITA:Ho creato questa cover per una mod che ho fatto...

3) Reduced the length of the front end because it was bumping into the top rail on my Ender 5. ...It is still very close, and on in the corner it brushes up against the corner brace at the 219-220mm area, but this just causes it to canter up slightly...

I use my Ender 3 Pro a lot, and thanks to that, both my Hot end fan and Parts cooling fan both gave up on me. This gave me a chance to upgrade each of them to a 40x20 hot end fan and a 40x20 parts cooling blower fan. I designed this to support both...

Noctua Fan Holder for Silent 40mm Noctua Fan on Ender 2 Control Board.

Ender 2 controll board fan holder for silent 40mm noctua fan.

SKR 1.3 Ender-3 Case | One side | 2 fans I wanted smallest possible case and I am not using Raspi so these double drawer designs were overkill. You will need: 4 x M5 bolts (you should have at least 2 from Ender) 3 x M3x20 bolts for the lid 8 x...

SKR 1.3 Ender-3 Case | One side drawer | 2 fansI wanted smallest possible case and I am not using Raspi so these double drawer designs were overkill.You will need:4 x M5 bolts (you should have at least 2 from Ender)3 x M3x20 bolts for the lid8 x...

This is a Remix and modified for Ender3V2 of 1) ENDER 3 SILENT FANG NOCTUA V2 (https://www.thingiverse.com/thing:4223929) and 2) Ender 3 V2 3DTouch/BLTouch Mount ( https://www.thingiverse.com/thing:4462870)

The standard fan cover makes noise. ...They work silently when you zoom out a certain distance. Silent Fan Cover for 12 cm fans.

It is resized to fit the cooling fans that are coming on the newer Ender 3's with wider tabs. Print in PETG for best performance, although I did the first in PLA and it last nearly 100 hours before one of the vents began to get out of shape from...

This is a rewritten part cooling duct designed for Ender/Cr-10 style hot ends, now resized to fit newer Ender 3's with wider tabs on their cooling fans. ... Print it in PETG for optimal performance, as I initially did the first one in PLA and it lasted...

**A few more versions of Lil Boxie for Ender 3.** One for a Microswiss hotend, and one for a copper T-shaped hotend. These are All 4010 fans. Probe offsets: -44.13, -6.78 **Update** 2-22-22 Added Boxie PinPoint E3 40MMF MK1.stl and ...

Lid for mainboard case on Ender 3 upgraded with second fan. ... Honeycomb covers for fans are there: https://www.thingiverse.com/thing:3280998

Many popular hotend fans that run silent are 40x20mm versus the stock 40x10mm model in the existing Ender 3 V2. Unfortunately the stock Ender hot end assembly shroud cover is too cramped to fit one. What I have done here is to modify the Ender 3 V2...

This is a modification of the [WellFan - Mean Well LRS-350-24 ultra silent PSU mod for Ender 3](https://www.thingiverse.com/thing:2967389) which allows for mounting a 92mm fan. ... This file only contains the upper part, the lower parts can be taken...

Thanks to eric-anastas for this magnificent design and for sharing the step file i had remixed it to add another filament Colling fan, i am not an expert in the air flow but i thought that by adding another fan this will make sure an enough air flow...

Thanks to eric-anastas for this magnificent design and for sharing the step file i had remixed it to add another filament Colling fan, i am not an expert in the air flow but i thought that by adding another fan this will make sure an enough air flow...

Ender 3 Max stock fan mount for micro swiss ender 3 use the nuts that came with micro swiss to hold fan side on left right does not need and use one for bl touch Made new firmware with correct level point link soon Bl touch attaches to micro swiss to...

I've created a custom replacement for the original electronic enclosure top on my Creality Ender-3, designed to enhance cooling of the stepper motor by positioning two 40mm fans directly above it.

This is remix of the Setsana Ender 3 Pro fan duct that I have modified to attach a 3DTouch Adjustable. ...It also has an angled front edge for better visibility of the nozzle.

... fans and direct extruder. ...If you want to use direct extruder it might be the best to use my mount https://cults3d.com/en/3d-model/various/ender-3-v2-direct-extrusion-mount-for-dual-gear Easy install with 1 screw. ...You might also need 2 doodly eyes

This is remix of the Setsana Ender 3 fan duct that I have modified to attach a BL Touch using the same offsets as the stock duct (the left side duct was shrunk slightly to fit the bl touch in it's original location). It also has an angled front edge...

... - Swap Anet AM8 Fans to Silent Noctua Fans. https://youtu.be/EAbkqQiAj2Q Two silent Noctua fans (40x10mm) are used in this upgrade of the Anet AM8 3D printer. ... Fans: https://www.czc.cz/noctua-nf-a4x10-flx/117081/ Custom Models for Upgrades