ender 3 s1 pro ribbon cable 3d models

... damage anything but it can wiggle out of place. Going past 240 will wear your ribbon over time anyway and at that coordinate you are pretty much off the build plate with your nozzle, the only time you would want to go that far is for a bed mesh.

COPY OF LINK BELOW - Printed for my Ender 5 S1 - Works Great https://www.thingiverse.com/thing:5345559

So My S1 Pro hot bed cable fried on me while trying to utilize the entire bed. When the Bed is all the way forward (towards me) the cable that goes into the base housing is super tight and apparently after a few days of printing like this caused one...

Cable guide for print head. ... Slides over existing guide and helps to turn the cable 90 degrees to eliminate bending the cable off - axis. ... Flat spot for zip tie to hold cable flat against guide after 90 degree rotation

Prints well without support. ...Clears frame when homing without a problem. I recommend using cable tie to hold the cable in place as I did on the photo.

Support to hold lower cable close to the machine for better support and routing

Remix of the lids for Michaels rear case for the Ender 3 Pro. I have increased the gap for the cables on the left side of the board case, and added a ribbon cable slot for the screen cables. I use the BTT touch screen, which has two ribbon cables,...

Remix of the lids for Michaels rear case for the Ender 3 Pro. I have increased the gap for the cables on the left side of the board case, and added a ribbon cable slot for the screen cables. I use the BTT touch screen, which has two ribbon cables,...

A Clip that gives the extruder ribbon cable extra support , Dose not pinch cable and lets it have some movement to reduce stress on wires and Does not interfere with normal printing. ...Slides on just like original clip

Creality Ender 3 Pro Display Ribbon Cable Clip The original design was too loose on my Ender 3 Pro printer. So, I tightened it, made it lighter without loosing strength. Also, I oriented the design the right way up, so that you can just drag...

As most everyone has done, I've installed a part tray between the screen and middle rail on my Ender 3/Pro. As a result, the screen's ribbon cable has nowhere natural to lay. I didn't want to force it behind the tray which would possibly bend the...

Ender 3 S1 Pro Drag Cable Chain Snap link. ...Link that snaps into stock ender 3 S1 pro cable slot. made to attach cable chain to the awkward ender 3 s1 pro cable mounts Printing at 10% scale should match the other pieces24x37.84x15.2mm

I created an Ender 3 Pro Ribbon cover inspired by Sparky277480's design, with a key feature being the added cutout for the 40mm Y-axis extrusion. Although I could have simply adapted his original model, I opted to hone my modeling skills by starting...

... S1 prov1 restricts x axis to260mmv2 allows for full extensionv3 is even smaller. ...I didn't test this one, just modeled itfor added stability, pair with snap link bellowhttps://www.printables.com/model/360429-ender-3-s1-pro-drag-cable-chain-snap-link

https://www.printables.com/de/model/297182-vertical-ribbon-cable-guideholder-for-ender-3-s1-p This is an alternative vertical cable guide for the Creality Ender 3 S1 Pro. The bracket on the extruder was designed so that the construction space of...

Just a remix of Ender LCD Ribbon cover and logo added from https://www.thingiverse.com/thing:3078936 I made some experiments with printing two colors. ...But it also looks fine if you just paint the logo bevel white after printing.

Printing Temperature: 300˚C Bed Temperature: 60˚C Printing Speed: 50mm/s Fan: OFF Direct Drive: Retraction Distance: 3mm Retraction Speed: 40mm/s REMIXED FROM: https://www.printables.com/model/417892-ender-3-s1-pro-heating-bed-cable-chainholder...

CREALITY ENDER-3 S1 PRO - CABLE HOLDER EXTRUDER Creality Ender-3 S1 Pro Upgrade and Modification, enjoy our Version. If you have any Questions, just write a Comment DISCLAIMER This Product may only be printed for Personal use and may not be Sold...

CREALITY ENDER-3 S1 PRO - CABLE HOLDER X-AXIS Creality Ender-3 S1 Pro Upgrade and Modification, enjoy our Version. If you have any Questions, just write a Comment DISCLAIMER This Product may only be printed for Personal use and may not be Sold...

CREALITY ENDER-3 S1 PRO - CABLE HOLDER Z-AXIS Creality Ender-3 S1 Pro Upgrade and Modification, enjoy our Version. If you have any Questions, just write a Comment DISCLAIMER This Product may only be printed for Personal use and may not be Sold...

Ender 3 S1 Pro Heated Bed Cable Chain. This chain link provides the offset needed from the heated bed to the printer. I used a little bit of Automotive black silicone to adhere the bottom part to the machine. You need to print: 1x...

This is a quick little box to hide your Ender 3 S1 controller ribbon after you convert to the Sonic Pad. I designed this to make switching between the Sonic Pad and the default controller quick and easy. It keeps the ribbon hidden without having to...

and I would strongly suggest these to be printed in PETG since PLA variants may warp from heat over time.These are the quantites and parts you will need from @Bananenminister's files : 16-Clips 15-Chain links1- Ground Plate1-Hook (to secure ground...

Sadly the original model doesn't fit with the ender s1 pro, so i made a little remix. There is a hole at the lower end, you can stick a little piece of filament trough, fixing the cable in place. I recommend printing with 100% Infill, the clips...

... a Thing for the Printhead Cable, because in my Opinion the Cable is bent to much ! It is Compatible with the Normal S1& Pro & Plus ! I Hope you also enjoy my Design ! ... Settings: 0,16 Layer Matt Black PLA With Support Printtime ca.1.5h

... safe angle. No any chain needed. :) It is Compatible with the Normal S1 & Pro & Plus! (Supports are not needed if you use the print position as in the picture. Best result at 0.12) PS This is the first thing to improve the printer! ...:)

Cover to hide (and protect) the ribbon cable of the Cre‎ality Ender 3.

Cover to hide (and protect) the ribbon cable of the Cre‎ality Ender 3.Category: Tools

Ender-3 S1 pro Gulf Coast Ribbon Cable Holder. I did not care for theirs so I designed my own. ... Category: 3D Printer Parts

This is a ribbon cable clip designed specifically for the Ender 3 Pro. The clip is large enough to securely fasten the ribbon cables on the printer with ease. I produced this item using Geeetech Black PLA filament. You can see this clip featured in...