ender 3 s1 pro ribbon cable 3d models
818951 3d models found related to ender 3 s1 pro ribbon cable.prusaprinters
... inserted in the guides (see pic #2) with this cable protector I don't have to. Plus I can slide the protector more easily up when I need to connect the ADXL345 mount.https://www.printables.com/model/213646-adxl345-mount-for-the-ender-3-s1
prusaprinters
You will have to scale the part a bit higher if your flow rate is higher to fit the original mount.I uploaded another version (V02) because some users found the fit too tight and there was not enough room for the cable.The component can be printed...
thingiverse
... off of a file by @ZaXaZ on Printables. Linked below https://www.printables.com/model/381729-ender-3-s1-pro-plus Basic concept taken from @dubs49 on Printables. ...Linked below https://www.printables.com/model/126842-serre-cable-ender-3s1-long
thingiverse
This remix does not offer any functional improvements over the original, but includes small dimensional changes to improve the fit over the clamp and alter the path of the cable swept section so it is biased from the centreline. ...Also some aesthetic...
thingiverse
Makes the cable at a more vertical angle Still, it is not completely free of gantry interference. ... If the height of the molding exceeds approximately 220 mm, remove this adapter.
thingiverse
This clip was designed specifically for the Ender 3 Pro, but it should also fit perfectly on the Ender 3. The clip is ideal for securing power supply cables up to 14 AWG and can be used in conjunction with the ribbon cable going to the LCD display to...
thingiverse
I wasn't thrilled with the other Ender 3 Pro cable covers available on Thingiverse, so I took matters into my own hands and designed my own. These custom covers print smoothly and snap firmly into place without any issues. ...If you decide to print this...
thingiverse
This is an Ender 3 S1 Pro chain for the extruder flat cable. This design probably doesn't work with other Ender 3 models due to the gantry support that S1 Pro has for the X-axis. ... You need to print: 1 - Extruder attachment (support needed) 39 -...
thingiverse
This is an Ender 3 S1 Pro chain for the bed heating cable. This design probably doesn't work with other Ender 3 models due to the closed carcass that S1 Pro has. ... You need to print: 1 - Bed attachment 13 - Chain parts 10 - Clips
thingiverse
In my opinion, the bottom cable of the Ender 3 S1 pro stuck out too far. This is a bracket that makes the lower cable point inwards. I use an M4 t-slot nut... ...works well.
prusaprinters
THANKS Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: Yes Resolution: 0.12 Infill: 100% Filament: Esun PETG Notes: You may get away without using any supports. I haven't tried. I use Prusa slicer with paint on...
thingiverse
Its just the way the sprite has been designed by creality with the cable coming out the centre of the extruder. But this support causes way less kink than the original part and some others on here. 3. You do not have to trim back the locking...
cults3d
Cable guide for the bed of the ender 3, with this mod you can bring the printer closer to the wall without disturbing the cable. Gain space with this mod, very easy to assemble, a support for the bed, another for the base and the chain. ... You use the...
thingiverse
Updated from the original by 1) Adding 1mm extra in ribbon cable width area. 2) Over hangs to hold ribbon in place. ... 3) Radius on the ribbon holder edges remove sharp edges.
thingiverse
CREALITY ENDER-3 S1 PRO - CABLE CLIP Creality Ender-3 S1 Pro Upgrade and Modification, enjoy our Version. If you have any Questions, just write a Comment DISCLAIMER This Product may only be printed for Personal use and may not be Sold...
thingiverse
Extruder ribbon cable stress relief mod , doesn`t hit the gantry while homing or reaching the max z height , easy to install & fits perfectly let me know if it works for you ! ...:D
thingiverse
... flat cable. ...Prevents end switch and X-axis motor wires from pulling and damage. On S1 Pro flat cable is a little wider and motor/end switch wires are shorter than on S1! ...That's why almost the same clips for S1 couldn't fit on S1 Pro perfectly.
cults3d
This small bracket helps reduce the wear on the x axis stepper motor wiring on the Ender 3 S1 Pro. Without it, my wiring is too short and the plug pulls out at full z height as shown in this review video https://youtu.be/zEVVV3jDUX8 Simple print and...
thingiverse
This small bracket helps reduce the wear on the x axis stepper motor wiring on the Ender 3 S1 Pro. Without it, my wiring is too short and the plug pulls out at full z height as shown in this review video https://youtu.be/zEVVV3jDUX8 Simple print...
cults3d
This small bracket helps reduce the wear on the x axis stepper motor wiring on the Ender 3 S1 Pro. Without it, my wiring is too short and the plug pulls out at full z height as shown in this review video https://youtu.be/zEVVV3jDUX8 Simple print and...
thingiverse
UPDATE (June 26, 2022) ==================== Based on the received comments, the version 2 of the ribbon sheath is now available and compatible with both Ender 3 S1 and S1 Pro. Please note that the sheath is printed at a 30deg angle, with supports...
thingiverse
Design this clip to hold cable from moving and damaging the x-axis cables. I also added an offset to keep it away from the heat of the servo motor. Bracket holds using the nut shown in the picture. ... you can insert the cable and clip it back.
thingiverse
I needed a bracket to keep my cable from ending up like so many others I've heard. ...I took measurements from my own printer and created this in tinkercad.
thingiverse
A simple change in orientation of the “cable_chain_side_lock” file allows the cable chain to run cleanly down the left side of the printer bed toward the front of the printer making the entire machine about 5 or 6 inches smaller side-to-side given...
thingiverse
https://www.printables.com/de/model/417892-ender-3-s1-pro-heating-bed-cable-chainholder Prevents cable breakage at the housing outlet and rubbing on the Y-axis motor. It can be attached to the underside of the housing and to the recess for the...
thingiverse
... damage anything but it can wiggle out of place. Going past 240 will wear your ribbon over time anyway and at that coordinate you are pretty much off the build plate with your nozzle, the only time you would want to go that far is for a bed mesh.