ender 3 s1 pro linear rail 3d models

WIP Had issues with overhangs, not being printed nicely at the back of the models, so I wanted to try with circular fan duct. Couldn't find one, built one on my own. I printed it vertically, using tree support, build plate only. ...I also used...

Should snuggly fit onto the front of your printhead to indicate the Norse Gods bless your project (and that the filament hasn't jammed!)

ENDER 3 S1

I ended up putting an ender 3 v2 hotend on my ender 3, with a Sprite SE extruder (and linear rail)After a few attempts this is what I've been using - cable chain support is remixed from mwnickerson CHPower Direct Drive Drag Chain as the...

The mount attaches to the X-axis rail under the two screws that hold the stock belt tension adjustment. The camera base folds around the shelf to secure it in place, and the USB cable slides into the cable holder to keep it out of the way while...

My Ender 3 uses a X axis linear rail and the SpeedDrive direct drive conversion with BMG extruder. I removed the top of the cable tower because it interferes with the use of my Speedrive BMG mount. I also put 4 holes in the mounting plate for my...

This is a mounting plate I designed to fit onto an MGN12H linear rail carriage for the Creality Ender 3 x axis. I seated my linear rail right next to the limit switch so that the carriage activates the switch without falling off or exposing any ball...

This is a mounting plate I designed to fit onto an MGN12H linear rail carriage for the Creality Ender 3 x axis. I seated my linear rail right next to the limit switch so that the carriage activates the switch without falling off or exposing any ball...

This is a simple solution to use the metal carriage and its parts on a endear 3 with linear X rail on the top. ...Will have to shave off the cable snap clips little piece poking out by the screws when the cable is snapped in for it to fit properly

Pre-lube everything if you want to do it now or save the mess & wait until its mounted.BOM1 x Ender-31 x 300mm MGN12H linear rail2 x M4x20mm screws2 x M4 t-nuts2 x M4 washers4 x M3x25mm screws16 x M3x8mm screws12 x M3 t-nuts4 x M3 locknuts12 x M3...

# BOM * 1 x Ender-3 * 1 x 300mm MGN12H linear rail * 2 x M4x20mm screws * 2 x [M4 t-nuts](https://www.amazon.com/s/ref=nb_sb_noss_2?url=search-alias%3Daps&field-keywords=m4+tnut) * 2 x M4 washers * 12 x M3x8mm screws * 12 x M3 t-nuts * 4 x M3x25mm...

Here's a brief summary and analysis of the content: **Summary:** The document provides step-by-step instructions on how to modify an 8-bit Delta printer to use MGN12H linear rails. The modifications include drilling new holes in the Y plate, mounting...

So the cooling fan/mount on the S1 pro is horrible. Here is a very simply upgrade,Simply remove the fan, flip the stainless steel bracket 180 degrees and mount back with two of the mounting holes. Obviously after you have printed and replace the fan...

0.16-.0.2 Layer 40% infil

The bracket provides an alternative way to fixate the filament sensor to the gantry. ...This can be useful, for example, in case the dedicated original spool holder fails, or is removed from the machine.

Prints well without support. Clears frame when homing without a problem. ... I recommend using cable tie to hold the cable in place as I did on the photo.

Do you like my work? Can you support me with a ☕ or maybe a 🍺? It all depends on the moment 😄 Double-sided guides to stick to the underside of your tray to place your PEI plate correctly and quickly. Suitable for a wide range of printers. ... I...

Esta en proceso de mejoras Imprimir a 180 grados respecto la cama

Support to hold lower cable close to the machine for better support and routing

I made this to lower my spool holder becuase it wouldn't fit on my shelf but i didnt want to make a whole nnew spool holder either. ... This goes right on you original spool holder like the normal stick does and then you just attach the spool stick to...

Cable guide for print head. Slides over existing guide and helps to turn the cable 90 degrees to eliminate bending the cable off - axis. ... Flat spot for zip tie to hold cable flat against guide after 90 degree rotation

... roundhead screws to secure the x-carriage hotend plate in place. This revised version builds upon the remix of SpeedDrive V1 - Ender 3 direct drive mount by sashalex007, tailored to fit the Ender 5 Linear Rails Mod created by KerseyFabrications.

Pre-lube everything if you want to do it now or save the mess & wait until its mounted.BOM1 x Ender-31 x 300mm MGN12H linear rail1 x M8x60mm or 1 x 5/16x2-1/4" bolt1 x M8 washer or 5/16" washer1 x M8 locknut or 5/16" locknut2 x M4x20mm screws2 x...

I remixed the bracket from H2FSPawn and Warump because I dont rely on 3D printed threads. Therefor I added sink holes for M4 Nuts (connection to bed) and M3 (connection for y-axis stop). ... Hope you like it.

part to be used to slot in the rail of an ender 3 printer

Here is the rewritten text: Reality Ender 3 rail insert quantities: Rail_Insert-200mm: 6 units Rail_Insert-141.5mm: 2 units Rail_Insert_200mm_Hole_Bottom: 1 unit Rail_Insert_200mm_Hole_Top: 1 unit

All the linear conversions I had found for my Ender 3 necessitated drilling of the Y plate. I prefer not to drill additional holes unless absolutely necessary, so here is my solution, including a simplified Y axis endswitch holder. V2 IS NOW...

I created this to mount a Creality Bed to Linear Rails Liner Rails I Used...

Attachment for rails on the Ender 3 printer is necessary, and it requires a nut, specifically an M6 or M7.

this is just a mount for ender 3 rails that you can glue on to any accessory.