ender 3 s1 pro linear rail 3d models

I made a thin, sleek, minimal and sturdy vertical PITFT50 V2 display mount for the Ender 3 S1 and S1 Pro without the Raspberry PI in the display casing. My Raspberry is laying behind the printer. You can print the Display_case and the...

I modified the z arm so that it would fit onto the S1 pro. ...Remixed from the original https://www.thingiverse.com/thing:3612390

Human: 2 MGNR12 300mm rails\r\n2 MGN12H blocks\r\n\r\nBed installation:\r\n4 M5x12 Hex socket head cap screws, Class 8.8 (https://www.tme.eu/en/details/b5x12_bn3/bolts/bossard/1004085/)\r\n4 M5 Hex nuts, Class 8.8...

Sadly the original model doesn't fit with the ender s1 pro, so i made a little remix. There is a hole at the lower end, you can stick a little piece of filament trough, fixing the cable in place. I recommend printing with 100% Infill, the clips...

and I would strongly suggest these to be printed in PETG since PLA variants may warp from heat over time.These are the quantites and parts you will need from @Bananenminister's files : 16-Clips 15-Chain links1- Ground Plate1-Hook (to secure ground...

My June 2022 Creality Ender 3 S1 Pro buzzer is crazy loud, and no other models I found fit. The buzzer noise is now reduced about as much as applying two pieces of 3m vinyl wrap on top of the hole, which I had previously. So, if you have adhesive...

This is an ender 3 Max linear rail mount for the x gantry. ... I used MGN9H and mount it on top for the bracket, I use the ender 3 v2 Top rails mod for the linear rail mount and bought a separate 400mm long MGN9H for the linear rails,

The Ender 3 S1 Pro has a big plastic base that covers up a lot of places where the switch for the 3D Chameleon color changing system could be mounted. I decided to go simple and mount the switch right on the plastic base using 3M Command Strips. So I...

Installation ===== * loose the right corner screws in the base of Ender 3 S1 pro, push the my mount print into and then put screws back * after that the pi case can be installed to the left with the dove tail joint * cam holder is easy as seen in...

Route filament from dry boxes to the Creality Ender 3 S1 Pro printer using this [Bowden tube guide](https://www.youtube.com/shorts/nfN7RhlbYGk). The assembly consists of a main control arm, a pulley hook, fitting plate, and snap locks to maintain the...

Unfortunately I couldn't find a spool holder with load cell that fits to the holder of my 3D printer (Ender 3 S1 Pro). I don't know if this design also works on other printers.I use a HX711 with 12,7x12,7x75 mm load cell (i use the 10kg load cell but...

This is a rack for hosting raspberry pi 4 installed with Octoprint as well as the camera holder.The pi rack is open designed to allow max air flow.For camera holder you will need to print number of arms large/medium/small to suite your need.At least...

This Ender rail cover user T -Bolts to secure to the V slots on the side. Allowing you to tension the belt freely without effecting the 3D printed part. Other models I have seen would not let you do this as the cover clipped on to the part that...

Y rail cover with more space for the full motion of the printbed. ...

The mount is easily installed on the existing rail without requiring any disassembly.

thirsty_camel made side-entry filament guide for Ender 3 S1, but it had too much of friction when filament was pulled from drybox. I designed these addons to use the original filament guide arm.I used two Wurth 608 2RS bearings. All things is made so...

For the second generation of my squash ball feet design for the Ender 3 S1 Pro, I decided to make 4 variations of the original model starting from scratch!The original model was rigid, simple, and effective; however, had shortcomings in the design...

Since my Ender 3 s1 pro has a filament spool rack with bearings in it i made this end-cap and spool spacer set to allow the spool to use the bearings instead of freely spin. You will need 2 spacers and 1 end-cap, Edit: complete re-write of...

Recipients of this instruction assume all risks associated with its implementation and release me from any responsibility for consequences thereof.Part ListPrinted Parts1x Creality Ender 3 S1 Pro Drawer1x Camera Case1x Cable Cover1x Camera...

Print this part on its side with standard supports for best results. ...Don't lose your 20mm rail caps next time! ...Happy printing

I'm not sure if it will fits to s1, but on my s1 pro it mounts perfectly fill free to remix of change as you want. These parts do need any screws except that were with printer or sonicpad. No screwdriver needed for mount. Sot it is easy to...

I adored the original rail cover, but it was a must that I had one emblazoned with Yoda's iconic visage. ...As such, this rendition is based on the more robust v2 model design.

This is a remix of the Y-axis rail cover designed by "da_syggy", boasting a compact opening at its forefront, allowing for seamless integration atop the PS3-EyeCam mount created by "writable".

I have uploaded a second version of the extruder mount (V2), which has elongated holes to hopefully address the issue.2 mounts for the FYSETC portable input shaper...

... cam needed a new mount platform. ... Using the measurements from PsychProd's mount + the end piece on the rail this remix was born. ... About to extend this and add a 200mm straight piece to potentially give a better advantage for OctoLapse captures.

This cleans up the look of the rail and protects the belt if you happen to grab it when moving the printer around. On the original, a handful of comments talked about how the printer bed would run into it when the y axis was at 230mm+, so I...

(At least on the Ender 3 V2 with the Sprite Pro extruder) You would then set the endstop position to keep the nozzle zero above the build plate. The fit is good, you will need slightly longer M3 screws than the ones originally used to mount the...

... in its upright orientation. This resulted in one side that attaches to the rail being slightly longer than the other. Additionally, this approach minimizes the number of supports required. ...To make removal easier, I set the support density to 10%.

This is an "inverted Bowden" adapter for the Ender 3 S1 Pro. Yeah, I know: what the F is an inverted bowden? So, basically, on a direct drive extruder system, you have a bowden tube running from the spool holder to the inlet of the extruder. This...

I remixed a side spool mount to hold a go_pro camera rig. I wanted a camera mount, but wanted it far enough away from the heated bed, I realized there was nothing like that out here so I made one. ... Designed in 3dBuilder sliced in CURA Supports:...