ender 3 s1 pro fan upgrade 3d models

The Ender 3 Pro spool shaft does not rotate so I figured it was simpler to have a non-rotating spool shaft for the Ender 3 S1 Pro. Although the part is printed with support, the only area of the part that is supported is the mounting detail. The...

Wyze Cam v3 mount for the Ender 3 S1 / Pro (only tested with the S1 Pro). Fits a Wyze cam v3 perfectly and at an optimal viewing angle. (Will not fit Wyze Cam v2 or older models) Mount fits the left side of the machine, can be flipped before...

Looked around and found a really good page on installing Klipper3D on the ender 3 S1 Pro on [3d Print Beginners Site](https://3dprintbeginner.com/install-klipper-on-ender-3-s1-pro/). Followed his instructions and had the ender printing with all the...

The hook tab on the mount slides perfectly into a small rectangular hole (10mm x 17mm) at the back of the Ender 3 S1 Pro near the stepper motor for the bed. I would assume this fits the S1 too and possibly other Creality printers if they have the...

Remix of https://www.printables.com/model/178884-ender-3-easy-space-saver-control-mount-easy-print- to allow it to work on the Ender-3 S1 Pro.  Removed the locating ‘bump’ on the back and shifted the mounting holes ~5mm to clearance the taller...

A space saving mount for your Ender-3 S1 Pro display with some space underneath it to stash your Raspberry Pi. I took inspiration from the Ender-3 S1 Pro Space Saver Control Mount, but wanted to add a place to stash my Raspberry Pi to free up some...

https://www.printables.com/de/model/297182-vertical-ribbon-cable-guideholder-for-ender-3-s1-p This is an alternative vertical cable guide for the Creality Ender 3 S1 Pro. The bracket on the extruder was designed so that the construction space of...

This is a mount designed for the Raspberry Pi Cam V2 to fit the Ender 3 S1 as well as the Ender 3 S1 Pro. It is mounted on the front on either sides of the printer and gives a diagonal view on the print bed for monitoring over klipper / octoprint.

Clip on Gantry spatula holde for Ender S1 Pro and any other printer with 2 x 2 cm Gantry.Tool holder ..

Remix of https://www.printables.com/model/178884-ender-3-easy-space-saver-control-mount-easy-print- to allow it to work on the Ender-3 S1 Pro.  Removed the locating ‘bump’ on the back and shifted the mounting holes ~5mm to clearance the taller S1 Pro...

... for Microsoft HD-3000 camera. ... This includes longer shaft and holder for HD-3000 webcam. You also need to print right or left printer mount from the DamianB2's "Webcam Holder for Ender 3 S1 Pro" project: https://www.thingiverse.com/thing:5765452

Holder for Trust Trino camera and an Ender 3 S1 (pro) printer. Camera can be placed on the front left of the printer. The original housing screw is long enough to screw the holder on the printer housing. I used a washer between the original...

This is the first thing I have ever created, it is designed to hold the 4 Allen keys that come with the ender 3 s1 pro printer. It measures in mm 7x7x26. Enjoy. ... Some of the keys may be tighter or looser depending on print settings.

Simple and easy to print Logitech C270 web cam mount for my Ender-3 S1 Pro.The flexible geometri holds the camera well and is easy to mount on the X-gantry.STL, STEP and Fusion360 files uploaded in case someone wants to modify it.

Creality Ender 3 S1 Pro Filament holder adapter (bearings)It is designed so that the coil easily unwinds from the holder and does not tend to get stuck.needed:2x Allen screw M52x bearing with an outer diameter of 30 and an inner diameter of 10 All...

A basic filament guide for the Ender 3 S1 Pro that prints in one piece with not support.I made it because I got rid of the filament runout sensor and I needed a very simple guide so the filament does not get stuck wile printing.

This a knurled belt tension adjustment knob cover for your Creality Ender 3 S1 Pro. Knobs are designed to fit very snuggly over the factory knobs so they don't spin while adjusting belt tension. ... Available as plain or w/ Omega logo Print...

I printed this on my Creality Ender 3 S1 Pro and also printed on my elegoo resin printer. It was a llittle tight when printed with resin vs filament with the same settings so I uploaded a standard, tighter and looser version. ... The one pictured...

air assist ring for laser head for ender 3 s1 pro either use thin double sided tape or super glue the ring in pace so that the set screw holds the air assist nozzle in place. the air assist nozzle i used is "18mm Aluminum Air Assist Nozzle 4mm Hose...

Two squash balls are needed to get your Creality Ender 3 S1/S1 Pro/S1 Plus a new low vibration, suppress sound feet. Intention is to easy attach them to the printer existing foot with no screws.&nbsp;</p><p>It is a remix of the <a...

This part it to adapt the official Ender 3 S1 Pro LED Light Bar Kit to work on an Ender 3 / pro / v2. https://www.creality3dofficial.com/products/ender-3s1-led-kit The adapter slips into the top rail and is secured with the outer most bolt that...

So I thought about a light shade for the Ender 3 S1 Pro and searched for it on Thingiverse. But what I found wasn't satisfactory to me. That's why I designed one from scratch. :-) Instead of many others, this design is different in some ways: ...

Remixed version of the Axolotl USB case by IlyaDruzhe to fit the components of the USB that comes with the Ender 3 S1 Pro. Exterior is essentially the same, with an extended head to fit the usb port. Interior is completely reworked to fit the...

The case mounts directly to the side of the Ender 3 S1 Pro, replacing the factory display mount. The display then mounts on top of this case. Enhancements : - It offers a higher angle for the display. - It has a downward facing fan slot....

When looking for a simple and effective design for squash ball feet for my Ender 3 S1 Pro, I couldn't find many models that I liked. Many of the models required modifications to the printer that were irreversible or seemed too flimsy for what I...

This is a 2x2 gridfinty base mount for the Creality Ender 3 S1-Pro left front base. **UPDATED**printed originally with PLA and that seemed to actually work but I would consider using PETG for rigidity. ... All and all this took a little while...

This is a Camera Mount for the Ender 3 S1 Pro that clips into the handle of the bed and it works quite well. Print it on its side as is, with supports, and 100% infill as the orientation of the beads will make the clips more flexible and...

Yet another filament spool holder using en M8 threaded shaft and 608RS bearings, works well on my Ender 3 S1 Pro base spool holder, i just replaced the rotating part with my own design.The "V" shaped form of this holder allows your filament spool to...

... spool. ... This bracket design uses the t-slot hardware that was supplied w/ the Ender 3 S1 Pro (for use with the handle file they provided), and off sets the Sonic Pad to the left. It allows the Sonic Pad to tilt from 33* to 90* from horizontal. ...

acessório ender 3 s1