ender 3 s1 pro calibration 3d models

No support needed. Print like how I oriented in the picture. Need a 60mm and a 40mm fan for the 6024 version. This version is very quiet. Need 2 40mm fans for the 4020 version You WILL need to relocate your BLtouch. ...There are relocation mounts...

This bracket will help reduce glare and allow better visibility from a standing or seated position.

As the Spatula doesn't fit in my tray in the printer and I wanted to have it accessible I printed the holder by irrational0. Now I rearranged my printer and had no room to use the holder, but needed it to mount on the left side of my printer.Easy...

New fan shroud I designed to allow for the best airflow to the nozzle and be adjustable for volcano/non volcano setups. This allows for the use of the existing lower screw that used to be to hold the fan in place and now be used as a position...

This is a Remix from a Mount previously uploaded. The holes where too small for the head screw in my printer. I decided to redo with similar dimensions removing bottom hole and making top hole bigger for the screw in my printer. I've also made...

MORE TUBE CLIPS Printing Temperature: 233˚C DON'T RUN OVER 245˚C It'll Start Smelling Like Breakfast Bed Temperature: 60˚C Printing Speed: 50 - 60mm/s Fan: ON FULL TILT

A basic mount designed to work with( https://www.amazon.com/Meggsi-Hygrometer-Thermometer-Temperature-Greenhouse/dp/B07W9LRV4K/ref=sr_1_1?crid=38ATJFT4G8C4W&keywords=b07w9lrv4k&qid=1661126353&sprefix=b07w9lrv4k%2Caps%2C131&sr=8-1) For checking temp...

I wasn't happy with the touch screen being the widest point of my printer, so I designed this to move it inboard and save some room. It prints in two pieces and snaps together, no supports required. It's a pretty good friction fit so no glue...

Read the print notes! I dont like the original position of the screen so i designed this bracket to put it in a better position. It was holding by the two original screws from the case (red circles). It fits a little bit strong but no problem to...

This is a Tolarance cover for the Cable connection with the sonic Pad. ... If you like it please Like and Comment your opinion :)

Remix I made to fit my Tapo C100 in the mount.

Combination for holder and chain.

This is a Remix from the V3 version from Aiirik, but I replaced the mount for the V2 Version. Worked very nice for me. ...

Mirrored the original mount and added a cut out so it can mount on the left side.Also extended out the camera mount points so the camera can be mounted below if required.

I printed this in PETG. This support prevents the rear bed cable snagging on the rear stepper motor. ...You will need 2 small cable ties and a hot glue gun.

Idea came from https://www.thingiverse.com/thing:5444181 but I found the clip too narrow for the cable so made a new clip with more allowances from scratch that fits much better. Print it in the same orientation as in the images, not as it comes...

My ribbon holder's screw holes had cracked because I had overtightened the M2.5 screws. I couldn't see why I should not continue to use the https://www.thingiverse.com/thing:5404277 and so I've remade the adapter from...

To store my Nozzels, I have designed an insert for my existing tray in which the Nozzels fit. Unfortunately, the numbering didn't come out well when printing. ...But I want to share it anyway.

This is a Z-axis camera mount which gives a rear view of the print bed, since the front and sides are blocked by my upgraded cooling vents. It is very stable and holds my heavy camera with no issues. ... Filament: PETG Layer Height: 0.2 ...

I dont like the original position of the screen. So i designed this bracket to put it in a better position. The adapter was hold by the two original screws of the case (red circles). It fits a little bit strong but no problem to instal. Enjoy...

This is a remix from ProperPrinting's simple tool changer. It's a very cool print in itself so go ahead and give him some love. The three parts are seperate objects so if you struggle with tolerances you can simply print them one after another. Long...

<p>This is a easy to print filament guide for all printers with 20x20 profiles.</p><p>You need a 8x16x5 bearing, a M3x20 screw and a M3 “melting nut”.</p><p>No supports needed.&nbsp;</p><p>Das ist eine Filamentführung für alle Drucker mit 20x20...

This is a remix of @JanLorenzen_1372689 https://www.printables.com/model/689977 for the Logitech 920 Web Cam https://amzn.eu/d/fbqlSN0The reason this is a Remix is that it is the part that Jan's model is designed for that is just so slightly smaller...

Normally, the filament runout sensor is directly screwed onto the filament spool. After I built a enclosure around my printer and placed the spool outside the enclosure, this was no longer possible.This sensor holder can be clicked directly onto the...

This design mounts the LCD at an offset atop the base to save space on the side of the printer. Use M4x12mm bolt and M4 nut to mount the LCD. ...Use the original LCD M4 bolts to fasten the 3d printed mount to the base.

This is a remix of the original cam and raspy holder from liyu1981, I just removed the raspy part since I did not need it. ...For a complete description (and giving some thanks for the original design) please visit the original design

I put the Ulanzi VL49 light on the printer to stream the print over night. So i dont have to use the big light all night. I think you can fit any other part there with the same connector. ...Maybe a camera or something.