ender 3 s1 pro calibration 3d models

My first post !

I made this as a simple bracket to attach a ADXL345 to a sprite extruder. ... The holes did come out a bit tight on a low quality print setting but i just run a 3mm drill through the holes.

Why? ---- Since I'm no longer using the Creatlity firmware and run Klipper instead, on this Fujitsu Futro S740, I demounted the default screen and use the spot for the mini-PC instead. This is a simple mounting bracket that uses the holes and...

There are other models made by different authors, mine has two differences.different shape of endstop pcblow profile, doesn't touch the bed with silicon spacersfill free to modify on onshape

C270 Logitech Camera Mount. Mounts on the end of the Z Axis arm, just slips over the end. Has a firm fit. This part uses the pieces from the original camera mount, specifically the hinge pin and screw and the two little sticky end covers if you...

The upper cable holder is remixed from romk's design ( https://www.thingiverse.com/thing:5423068 ). The lower cable holder is remixed from Sshelb8's design ( https://www.thingiverse.com/thing:6176160 ). ...Together, the two hold the extruder cable...

My Stock Flat Cable Holder broke.... So I made a new one wich replaces the original one. I made it of 2 parts for easy printing. Assembled without additional material. For protecting the flat cable i also put some stripes of duct tape to it...

A remix of the tray insert published by turbett1. I removed the tray bottom to reduce print time and increase storage volume. ...I also made the snips easier to remove by adjusting the storage between the handles to allow room to get your finger under...

Added a hole to put nozzle cleaning needle in and decreased the fillament usage. ... Can be printed without supports.

I created this remix without the sidewalls in order to save time in printing and use less filament. But I still haven't printed a proof to evaluate the result. ... If you print it, share your result.

I designed this bracket to relocate the filament run out sensor to the middle so the angle of the filament is centred when having 2 spools fitted. ...Print on its side to avoid layers from separating.

<p>Read the print notes!</p><p>I dont like the original position of the screen so i designed this bracket to put it in a better position.<br>It was holding by the two original screws from the case (red circles).<br>It fits a little bit strong but no...

this is an alternativ to the heatbed cable chain many are using just use TPU, no supports required

It can make your 3D printer more sturdy and reduce any annoying vibrations. However, you should be aware that using this kit will mean losing the original LED light bar. If you're using klipper, you can measure the resonance and see that the...

OP's chains work great however, I noticed some binding near the extruder attachment. ...I used 5 modified chains to reduce binding and increase flexibility in some positions.

I wanted to mount my RPi 4 running Klipper where the touchscreen After printing it should slot into the touchscreen mount just fine - the Pi can be mounted using M2.5 screws or standoffs Enjoy!

Remix of great Z-axis mount for a popular C270 webcam by @BKT_C5. My part of design is a little bit sloppy, because I was too lazy to do it from scratch and used piece of my own mesh for railing mount. See screenshot for how to place on the...

The upper cable holder is remixed from romk's design ( https://www.thingiverse.com/thing:5423068 ). The lower cable holder is remixed from Sshelb8's design ( https://www.thingiverse.com/thing:6176160 ). ...Together, the two hold the extruder cable...

Don't try add-ons. Ditch the stock cable guide completely. Save your ribbon cable from premature wear. I had to alter the retainer clips slightly to get it to fit. Pull the retainers out and snip the outer nubs off. ...From there everything should...

I loved the minimalist bed handle by schroedaa, but it was a bit too tall and the parts cooling fan was impacting the handle, so I trimmed the handle pull down by 5mm. ...Everything clears fine now and there's still enough handle to pull on.

This is a left front mount for a Creality Camera that works with the Creality Box 2.0 . I have not tested it yet I will upload pictures as soon as I have printed and tested it. UPDATE : Print the bolt part in 100% infill as it breaks off...

This is a remix to print in less then 5h

My cable eventually got damaged and I had to replace it. My solution to avoid it happening again is to bring the ribbon cable to the front and use this bracket. Print as my screenshot, with support, to increase strength. USE 2 x M3 nuts and...

This holder is attached to the hot bed corner without any bolt or nut. But you will obviously need a bolt to attach the camera to the holder. ...You can also print a camera attacment screw form here: https://www.thingiverse.com/thing:2749041

A simple bed-level test to make sure that your printer is leveled correctly !!only print one layer!!

Simple replacement for the original bed handle. Designed it for my IKEA Lack Enclosure because the standard was too long for my purpose. You can use the original screws. ...

Handle with support for Sonic Pad sensor. You will need 2 threaded nuts M3x4x5 and 2 screws M3x8 Print Settings Supports: NotInfill:100Filament:PETG

A holder for the flat cable that keeps it in its natural shape, reduces the strain on the Х motor cables. ...No screws or tools needed.

Couldn't find one, so I made one on Tinkercad.