ender 3 s1 pro cable 3d models

I am using an enclosure with IKEA LACK. ...By default the S1 Pro display is mounted on the side. ...I made an adapter to mount it vertically because it is difficult for me to use.

This is actually not a remix, but an Add-On for S1 Pro owners who whant to use the "remixed" cable solution. With this way of cable management, when you print tall objects, the cable needs some extra space exactly where the light fixture is. So I...

NOTE- Due to serious bed mesh issues with my S1 Pro, I was not able to print this final STL version, but other than the change to shape between clipper handles (seen in the STL, but not shown in the pics), everything else is the same so it should...

This is a movable turret for installing a direct drive sprite extruder onto Creality Ender 3. The loom cable passes through the hole left from your old Boden extruder. It enables full extension of the X,Y and Z axis of your printer with very...

compared to the original: -This model is more specific for the ender 3 s1/s1 pro. -An overhang has been added to grip the Y carriage plate and prevent slop. -A second set of snaps have been added to improve the retention and keep the forces...

This is a remix of a previous S1 Pro Camera mount and a flex arm camera mount that I meshed together to get more of what I needed. ... Original Mount:https://www.thingiverse.com/thing:5396885 Original Flex Arm:...

I am very new to modeling and printing. See Print Settings Notes for further printing details. Print Settings Printer: Ender 3 S1 Pro Rafts: No Supports: Yes Resolution: 0.2 Infill: 20% Filament: Hatchbox PLA Black Notes: Supports: Printed with...

This is a remix of a previous S1 Pro Camera mount and a flex arm camera mount that I meshed together to get more of what I needed.Original Mount: https://www.thingiverse.com/thing:5396885 Original Flex Arm:...

Although I've only tested this on the S1 Pro, it should also work on the S1 and the S1 Plus, as I believe they all share the same gantry design. You'll need either 8x 10mmx2mm or 4x 10mmx4mm neodymium magnets for this. As strong as you can get...

Bed leveling fix for Ender 3 S1 models.Follow word doc instructions or reposition ABL using provided filesDoc source: https://www.facebook.com/groups/602529180853579/permalink/723427122097117/?fs=e&s=clThe following can be done with custom firmware...

This is the remix for https://www.thingiverse.com/thing:3209211 with stock S1 / S1 Pro mount.

It all depends on the time 😄---Reinforced part to fix the "Nema 17" motors of the Z axis on Creality Ender 3 S1 and S1 PRO printers as well as for other printer models that use a 40/20 aluminum extrusion profile.I created this reinforced part...

*This is a remix of [this design on Printables](https://www.printables.com/model/475690-ender-s1-gantry-light-bar).* --- This is a printable light bar support that screws into the existing hex screws at the back of the gantry, no additional screws...

You will have to snap the two pieces together they are fairly tight and will not come apart easily.Print SettingsPrinter:Creality Ender 3Resolution: 1.2Infill:20%Filament:Stronghero3D PETGBlack Notes: I Printed in PETG on a PEI bed but...

Turn each stepper until they are both equally snug / compressed between the X axis extrusion and the top of the S1 Pro base plate. Tighten down your grub screws and make sure they are sandwiched properly against their pulleys. Also ensure the...

A corner piece that fits into the S1 Pro with a mount point on top that can be used for a columnto mount a camera or any other accessory you might need. You just take off the two scews pop the part in and put the screws back. Also added a simple...

Ender 3s1pro cam mount

Drawer_pi3_v1 is just the remixed part to fit the pi 3 Drawer_pi3_withwirecutoutsandgrill is it with wire cutouts and a grill for airflow Drawerreceded is the same as the one above except the pi is pushed back so that the ports aren't exposed. It...

Clip that uses the bolt from the lower Z carriage wheel to hold the band cable so the x end stop and motor cable arent under stress.

Secures the unprotected cables for the X axis motor and X axis limit switch. ...

... just stops the annoying glare from hitting your eyes.  it does not affect platform lighting at all unfortunately the part is too long for an ender 3 bed so ull  need to print this model twice print is as simple as it gets no infill no support enjoy

I expanded the groove a little for a wide cable and made the opening a little wider and more convenient in order to install the cable. In the original model, this was quite difficult to do. ...I made a small ledge so that the thin wires to the motor...

A little clip that holds the extruder ribbon cable in place. Designed to reduce stress on the X motor wires. ...No screws or tools needed.

This simple print screws in place and angles the cable 90 degrees - no modification necessary! Not only is really functional but looks cool too! ###Update: Sometimes the cable gets lodged behind the motor when the bed moves all the way to the...

Added a arm with a small screw with 1/4-20 UNC threads and a cable pass-through on the arm. Add a bit of teflon tape to the screw to make the webcam sit a bit more snug. ...

There' s 2 models, one flat one 45° degre For hold and guide cable printer and caméra For the flat model, use it fefore the first screw, and for angle model, between the 2 screws, just twist it! ...

This remix does not offer any functional improvements over the original, but includes small dimensional changes to improve the fit over the clamp and alter the path of the cable swept section so it is biased from the centreline. ...Also some aesthetic...

Made 3 extra version with different angles to accomodate for different viewing angles, original one was the 50° version, the printed one on display here is the 60° Extra I recommend printing sideways (the way the STLs come) with tree supports. i...

(Y is the carriage, right?) That way you cannot insert the cable at the wrong spot like I did. TWICE. :-( See that blank spot at the cable for the end stop? Don't hurt your poor printer like I did, it's not his fault, creality can't get it right on...

2023.3.6 UP DATE Added Rod riser clip 10mmRise ＆ 15mmRise Replace mounting bolts with M3x8mm bolts. Use M3x10mm bolts for knobs. The thickness of the mounting portion of the dial gauge is 8mm. Use extension rods. ... 【注意】 ...