ender 3 s1 pro cable guide 3d models
880886 3d models found related to ender 3 s1 pro cable guide.
thingiverse
Ender 3 S1 Pro Heated Bed Cable Chain. This chain link provides the offset needed from the heated bed to the printer. I used a little bit of Automotive black silicone to adhere the bottom part to the machine. You need to print: 1x...
prusaprinters
and I would strongly suggest these to be printed in PETG since PLA variants may warp from heat over time.These are the quantites and parts you will need from @Bananenminister's files : 16-Clips 15-Chain links1- Ground Plate1-Hook (to secure ground...
thingiverse
Sadly the original model doesn't fit with the ender s1 pro, so i made a little remix. There is a hole at the lower end, you can stick a little piece of filament trough, fixing the cable in place. I recommend printing with 100% Infill, the clips...
thingiverse
... a Thing for the Printhead Cable, because in my Opinion the Cable is bent to much ! It is Compatible with the Normal S1& Pro & Plus ! I Hope you also enjoy my Design ! ... Settings: 0,16 Layer Matt Black PLA With Support Printtime ca.1.5h
thingiverse
... safe angle. No any chain needed. :) It is Compatible with the Normal S1 & Pro & Plus! (Supports are not needed if you use the print position as in the picture. Best result at 0.12) PS This is the first thing to improve the printer! ...:)
thingiverse
A holder for the flat cable that keeps it in its natural shape, reduces the strain on the Х motor cables. ...No screws or tools needed.
cults3d
I printed this in PETG. ...This support prevents the rear bed cable snagging on the rear stepper motor. ...You will need 2 small cable ties and a hot glue gun.
thingiverse
I printed this in PETG. ...This support prevents the rear bed cable snagging on the rear stepper motor. ...You will need 2 small cable ties and a hot glue gun.
thingiverse
this is an alternativ to the heatbed cable chain many are using just use TPU, no supports required
thingiverse
My solution to avoid it happening again is to bring the ribbon cable to the front and use this bracket. Print as my screenshot, with support, to increase strength. USE 2 x M3 nuts and bolts to fasten together. ... NOW ALSO INCLUDES CABLE STAY!!!
prusaprinters
... design ( https://www.thingiverse.com/thing:6176160 ). Together, the two hold the extruder cable parallel with the body of the printer and eliminate strain on the smaller connectors.The upper holder requires a tree support for the small overhang.
thingiverse
... design ( https://www.thingiverse.com/thing:6176160 ). Together, the two hold the extruder cable parallel with the body of the printer and eliminate strain on the smaller connectors.The upper holder requires a tree support for the small overhang.
thingiverse
This is a Tolarance cover for the Cable connection with the sonic Pad. ... If you like it please Like and Comment your opinion :)
thingiverse
... ... So I made a new one wich replaces the original one. I made it of 2 parts for easy printing. Assembled without additional material. For protecting the flat cable i also put some stripes of duct tape to it (see pic.) Fully optional. ...
thingiverse
Idea came from https://www.thingiverse.com/thing:5444181 but I found the clip too narrow for the cable so made a new clip with more allowances from scratch that fits much better. Print it in the same orientation as in the images, not as it comes...
cults3d
... work. Print in the orientation as downloaded in order to print with no supports. All feedback is appreciated. I have an Ender 3 Pro, but I am assuming it will work on an Ender 3 as well. ...May also work with other similar Creality printers.
thingiverse
... model oriented as downloaded to print with no supports needed. All feedback is greatly appreciated. I've tested it on an Ender 3 Pro but assume it will work equally well on an Ender 3; it may also be compatible with other similar Creality printers.
thingiverse
3D printer filament guide specifically for the Ender 3 S1. For a dehydrator at the same level as your 3D printer. It guides the filament from and to the filament senor to the extruder. I used ABS for a stronger print. Sanded the hole a little to make...
prusaprinters
Ender-3 S1 pro Gulf Coast Ribbon Cable Holder. I did not care for theirs so I designed my own. ... Category: 3D Printer Parts
thingiverse
A cable sheath for the Creality ender 3 S1 and S1 Pro cable that connects to the extruder to prevent twisting or breaking. This accessory is composed of two halves that hold tight the end of the cable at the change of section and also change it's...
thingiverse
A remix of AJCam44's excellent cable support for Ender 3 S1 Pro. I adapted it to fit the S1 non pro. Also I added support for extra wiring shown in the photos. Should work with PLA but I used PETG. The bottom support bracket is very different...
prusaprinters
... inserted in the guides (see pic #2) with this cable protector I don't have to. Plus I can slide the protector more easily up when I need to connect the ADXL345 mount.https://www.printables.com/model/213646-adxl345-mount-for-the-ender-3-s1
thingiverse
This is cable chain for Ender 3 s1 3D printer. You are need print 15 chain link and glue the two parts of the top. ... The bottom is attached to the profile, the top is attached to the roller bolt.
cults3d
cable clamp for 3 S1, avoids pulling out the motor wires and end of stroke sensor.
prusaprinters
Remix of Diogosantos88's Drag Chain - Cable Chain - Ender 3 Still Work in Progress Main Chain is DoneBest way to attach the Under_Printer_Clip is to look for the wide gap where the cable exits the printer > Put in one end of the print...
thingiverse
- JST ATTACK - Eurekaled LED CHANNEL WITHOUT ANY MODIFICATION TO THE PRINTER, I MADE A LIGHT FOR THE ENDER 3 S1 PRO. TO BE PRINTED 2 PLA ARMS WITH PRECISE FITTING TO ACCOMMODATE THE ALUMINUM LED TRUNKING. YOU MUST ALSO PRINT 4 ELEMENTS, ALWAYS...