ender 3 s1 pro cable guide 3d models

It's a remix from https://www.thingiverse.com/thing:5953410, but much stronger because my cable is harder than on the regular S1 printer.And also on my design is lot more space for cables.But the idea of the original design was very good and now it...

Design this clip to hold cable from moving and damaging the x-axis cables. I also added an offset to keep it away from the heat of the servo motor. Bracket holds using the nut shown in the picture. ... you can insert the cable and clip it back.

A simple change in orientation of the “cable_chain_side_lock” file allows the cable chain to run cleanly down the left side of the printer bed toward the front of the printer making the entire machine about 5 or 6 inches smaller side-to-side given...

It all depends on the moment 😄 Double-sided guides to stick to the underside of your tray to place your PEI plate correctly and quickly. Suitable for a wide range of printers. ... I placed them only at the back of the bed to give the position but you...

UPDATE (June 26, 2022) ==================== Based on the received comments, the version 2 of the ribbon sheath is now available and compatible with both Ender 3 S1 and S1 Pro. Please note that the sheath is printed at a 30deg angle, with supports...

https://www.printables.com/de/model/417892-ender-3-s1-pro-heating-bed-cable-chainholder Prevents cable breakage at the housing outlet and rubbing on the Y-axis motor. It can be attached to the underside of the housing and to the recess for the...

COPY OF LINK BELOW - Printed for my Ender 5 S1 - Works Great https://www.thingiverse.com/thing:5345559

So My S1 Pro hot bed cable fried on me while trying to utilize the entire bed. When the Bed is all the way forward (towards me) the cable that goes into the base housing is super tight and apparently after a few days of printing like this caused one...

Prints well without support. ...Clears frame when homing without a problem. I recommend using cable tie to hold the cable in place as I did on the photo.

Support to hold lower cable close to the machine for better support and routing

I wanted a simple snap on filament guide for my Ender 3 S1 pro. ... Remixed this from: https://www.thingiverse.com/thing:4428057 https://www.thingiverse.com/thing:5419960 Needs support for the hole

A basic filament guide for the Ender 3 S1 Pro that prints in one piece with not support.I made it because I got rid of the filament runout sensor and I needed a very simple guide so the filament does not get stuck wile printing.

The Ender-3 S1 Pro normally comes with some extra hardware and the M5X50mm bolt is the same that is used to attach the uprights. It uses two (625 - 5mm x 16mm x 5mm) and two (685 - 5mm x 11 mm x 5 mm) ball bearings. The 625 bearings are the...

Ender 3 S1 Pro Drag Cable Chain Snap link. ...Link that snaps into stock ender 3 S1 pro cable slot. made to attach cable chain to the awkward ender 3 s1 pro cable mounts Printing at 10% scale should match the other pieces24x37.84x15.2mm

I printed this on my Creality Ender 3 S1 Pro and also printed on my elegoo resin printer. It was a llittle tight when printed with resin vs filament with the same settings so I uploaded a standard, tighter and looser version. ... The one pictured...

thirsty_camel made side-entry filament guide for Ender 3 S1, but it had too much of friction when filament was pulled from drybox. I designed these addons to use the original filament guide arm.I used two Wurth 608 2RS bearings. All things is made so...

... S1 prov1 restricts x axis to260mmv2 allows for full extensionv3 is even smaller. ...I didn't test this one, just modeled itfor added stability, pair with snap link bellowhttps://www.printables.com/model/360429-ender-3-s1-pro-drag-cable-chain-snap-link

Route filament from dry boxes to the Creality Ender 3 S1 Pro printer using this [Bowden tube guide](https://www.youtube.com/shorts/nfN7RhlbYGk). The assembly consists of a main control arm, a pulley hook, fitting plate, and snap locks to maintain the...

Simple filament guide that's plugged into the stock S1/S1Pro spool holder.

Ender 3 S1 cable guide

Printing Temperature: 300˚C Bed Temperature: 60˚C Printing Speed: 50mm/s Fan: OFF Direct Drive: Retraction Distance: 3mm Retraction Speed: 40mm/s REMIXED FROM: https://www.printables.com/model/417892-ender-3-s1-pro-heating-bed-cable-chainholder...

Adjusted fit the creality ender 3 pro aluminum extruder. ...Adjusted hieght for mount and width of mount to fit screw hole correctly

Here are 2 filament guides that clip to the top of the gantry. Can be used instead of the filament sensor or in my case I use it as I often use 2 filaments ready to go. 2 Versions, a 4.2mm hole and 4.4mm to be used with fuzzy skin (refer to print...

This is a easy to print filament guide for all printers with 20x20 profiles.You need a 8x16x5 bearing, a M3x20 screw and a M3 “melting nut”.No supports needed. Das ist eine Filamentführung für alle Drucker mit 20x20 Profilen.Du brauchst ein...

CREALITY ENDER-3 S1 PRO - CABLE HOLDER Z-AXIS Creality Ender-3 S1 Pro Upgrade and Modification, enjoy our Version. If you have any Questions, just write a Comment DISCLAIMER This Product may only be printed for Personal use and may not be Sold...

CREALITY ENDER-3 S1 PRO - CABLE HOLDER EXTRUDER Creality Ender-3 S1 Pro Upgrade and Modification, enjoy our Version. If you have any Questions, just write a Comment DISCLAIMER This Product may only be printed for Personal use and may not be Sold...

CREALITY ENDER-3 S1 PRO - CABLE HOLDER X-AXIS Creality Ender-3 S1 Pro Upgrade and Modification, enjoy our Version. If you have any Questions, just write a Comment DISCLAIMER This Product may only be printed for Personal use and may not be Sold...

After mounting all my Ender's electronics remotely, the cable pass-thru is too good to pass up for my Pi camera cable - but not with those sharp edges. I beveled all edges the cable will touch, so cables slide very easily. ...-My camera cable slides...

This is a clamp/guide for a mod to the heated bed cable that may snag on the y axis stepper motor at the rear of the printer. Mine snagged from new so i made this to keep the cable straight. I printed draft low quality (0.28) in Cura 5 with std...

Roller guide for extruder cable, a simple setup that requires just two pieces of 1.75mm filament to secure the roller in place. To complete the project, be sure to print two separate rollers. ...If you need any modifications made to the design, feel...