ender 3 s1 pro cable guide 3d models

... ...Ditch the stock cable guide completely. Save your ribbon cable from premature wear. I had to alter the retainer clips slightly to get it to fit. Pull the retainers out and snip the outer nubs off. ...From there everything should work perfectly.

Makes the cable at a more vertical angle Still, it is not completely free of gantry interference. ... If the height of the molding exceeds approximately 220 mm, remove this adapter.

I needed a bracket to keep my cable from ending up like so many others I've heard. ...I took measurements from my own printer and created this in tinkercad.

Cable guide for the bed of the ender 3, with this mod you can bring the printer closer to the wall without disturbing the cable. Gain space with this mod, very easy to assemble, a support for the bed, another for the base and the chain. ... You use the...

Cable guide for print head. ... Slides over existing guide and helps to turn the cable 90 degrees to eliminate bending the cable off - axis. ... Flat spot for zip tie to hold cable flat against guide after 90 degree rotation

https://www.printables.com/de/model/297182-vertical-ribbon-cable-guideholder-for-ender-3-s1-p This is an alternative vertical cable guide for the Creality Ender 3 S1 Pro. The bracket on the extruder was designed so that the construction space of...

You will have to scale the part a bit higher if your flow rate is higher to fit the original mount.I uploaded another version (V02) because some users found the fit too tight and there was not enough room for the cable.The component can be printed...

This is a remix of Ender 3 S1 CableGuide. This clamp holds the ribbon cable in place close to the printer just above where it exits the base. It bolts to the Z-axis frame using a bolt and nut provided in the spare parts that should have come with...

Extruder_ribbon_cable_guide for Ender-3_S1

The BEST cable guide for Creality Sprite Extruder. ...Can be clamped with a M3 x 10 mm screw or a cable tie. Uses the original mounting screws. Ender 3 S1 Ender 3 S1 Pro Ender 3 S1 Plus Ender CR-10 Smart

Filament Guide for Ender 3 s1 Pro in Cura Software Infill 80% Support Checked

**Link to download** https://www.printables.com/model/517570-ender-s1-s1-pro-bed-cable-guide This should fix the issue with the heated bed wires from flexing over and rubbing on the motor. Installation notes. 1-remove the screw right under...

Ender 3 S1 / S1 pro wire guide X axis

cable for heat bed ender 3 s1 pro

... ...It works on the Ender 3 s1 Pro for sure and may work on other ender 3 models. Several prints completed with no binding or excess friction. Edit: There has been negative experiences printing with PETG. ...File was designed with PLA in mind.

This's the ender3 s1 pro filament guide that works with rice bucket(Moisture-proof box). ... 3mm & 3.5mm bushings chose by yourself,3.5mm is recommended.

This is Filament Guide for the Ender 3 S1 Pro (maybe also non Pro) with Filament storage behind the Printer. I had the issue that with PTFE tubing to the printer or non guided feeding, the resistant was too much and there has been areas with...

Remixed for the Ender 3 S1 Plus. Mounted on the inside of the gantry, just bellow the stepper motor mount. ...Original design by: StarTony

There' s 2 models, one flat one 45° degre For hold and guide cable printer and caméra For the flat model, use it fefore the first screw, and for angle model, between the 2 screws, just twist it! ...

This is an Ender 3 S1 Pro chain for the extruder flat cable. This design probably doesn't work with other Ender 3 models due to the gantry support that S1 Pro has for the X-axis. ... You need to print: 1 - Extruder attachment (support needed) 39 -...

This is an Ender 3 S1 Pro chain for the bed heating cable. This design probably doesn't work with other Ender 3 models due to the closed carcass that S1 Pro has. ... You need to print: 1 - Bed attachment 13 - Chain parts 10 - Clips

In my opinion, the bottom cable of the Ender 3 S1 pro stuck out too far. This is a bracket that makes the lower cable point inwards. I use an M4 t-slot nut... ...works well.

... guide that mounts on the filament spool hook to gudie the cabel from a drier box. ...Make two copies and glue together with cyano acrylate. To install you need to remove the cap from the end of the spool holder, slide on the guide and then replace.

This remix does not offer any functional improvements over the original, but includes small dimensional changes to improve the fit over the clamp and alter the path of the cable swept section so it is biased from the centreline. ...Also some aesthetic...

CREALITY ENDER-3 S1 PRO - CABLE CLIP Creality Ender-3 S1 Pro Upgrade and Modification, enjoy our Version. If you have any Questions, just write a Comment DISCLAIMER This Product may only be printed for Personal use and may not be Sold...

Upgrade the positioning fixture of the Z-axis linear guide for Ender 3 S1 Ender 3 S1 Pro, and it is recommended to print 3 or 4 of them. Start using them at 14 minutes and 32 seconds in the video https://youtu.be/mqKDoieQxgk . ...Use the platform board...

... flat cable. ...Prevents end switch and X-axis motor wires from pulling and damage. On S1 Pro flat cable is a little wider and motor/end switch wires are shorter than on S1! ...That's why almost the same clips for S1 couldn't fit on S1 Pro perfectly.

This small bracket helps reduce the wear on the x axis stepper motor wiring on the Ender 3 S1 Pro. Without it, my wiring is too short and the plug pulls out at full z height as shown in this review video https://youtu.be/zEVVV3jDUX8 Simple print and...

This small bracket helps reduce the wear on the x axis stepper motor wiring on the Ender 3 S1 Pro. Without it, my wiring is too short and the plug pulls out at full z height as shown in this review video https://youtu.be/zEVVV3jDUX8 Simple print...

This small bracket helps reduce the wear on the x axis stepper motor wiring on the Ender 3 S1 Pro. Without it, my wiring is too short and the plug pulls out at full z height as shown in this review video https://youtu.be/zEVVV3jDUX8 Simple print and...