ender 3 ribbon cable replacement 3d models

Creality Ender 3 Pro Display Ribbon Cable Clip The original design was too loose on my Ender 3 Pro printer. So, I tightened it, made it lighter without loosing strength. Also, I oriented the design the right way up, so that you can just drag...

On my Ender 3, I used an excellent Pi case from https://www.thingiverse.com/thing:3075921 and mounted it upside-down underneath the LCD display. Then, I glued my cable guide to the side of the case. The ribbon cable is routed between the upper and...

... Cam with a bit of room to spare so it's not too tight. Printed it flat on my Ender 3 in 15 minutes on low quality and with supports for the middle section (which are easy to remove). ... Thanks to Smokyjoe for the original design (thing:2981386).

I also didn't want the cable to dangle if I ever transport the printer, so I created an existing clip to hold the ribbon cable in place. It meets a specific need for me and I'm sure someone else can find it useful as well. The clip is super strong...

Clip is used to neatly manage ribbon cable from controller to display Ender-3 Printer. Version 3 functions flawlessly. Version 4 represents an enhanced version with refined aesthetics. ...If you prefer your designs to appear flawless, use Version 4.

This is a remix of sahansudeepa's Ender 3 Cable Clip with the Green Lantern symbol added.

Remix of the model for the Ender 3 V2 from here : https://www.thingiverse.com/thing:3534331 I extended the back end of the slanted SD card slot to accommodate the ribbon cable. V2 file has the additional hole for securing to the bottom of the...

Remix of the model for the Ender 3 V2 from here : https://www.thingiverse.com/thing:3534331 I extended the back end of the slanted SD card slot to accommodate the ribbon cable. V2 file has the additional hole for securing to the bottom of the...

Remix of the model for the Ender 3 V2 from here : https://www.thingiverse.com/thing:3534331 I extended the back end of the slanted SD card slot to accommodate the ribbon cable. V2 file has the additional hole for securing to the bottom of the...

I remade the ribbon clip from TheToddRod's Ender 3 Pro Wire Clips to perfectly match my Ender 3 and Raspberry Pi ribbon cable.

I created an Ender 3 Pro Ribbon cover inspired by Sparky277480's design, with a key feature being the added cutout for the 40mm Y-axis extrusion. Although I could have simply adapted his original model, I opted to hone my modeling skills by starting...

Extruder ribbon cable stress relief mod , doesn`t hit the gantry while homing or reaching the max z height , easy to install & fits perfectly let me know if it works for you ! ...:D

Just a remix of Ender LCD Ribbon cover and logo added from https://www.thingiverse.com/thing:3078936 I made some experiments with printing two colors. ...But it also looks fine if you just paint the logo bevel white after printing.

You will have to scale the part a bit higher if your flow rate is higher to fit the original mount.I uploaded another version (V02) because some users found the fit too tight and there was not enough room for the cable.The component can be printed...

Cable Covering for LCD at End

This is base plate to go with the cable clip by gn-jr so that clips can be mounted off the printer. ... I glued several of these plates within my enclosure and used the cable clip to attach my extended display cable.

I opted to run the cable chain under the camera as it would shave off about 50mm of cable, and the one I bought was right at the limit if I were to print something large, a scenario that's probably never going to be an issue but one that still nagged...

THANKS Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: Yes Resolution: 0.12 Infill: 100% Filament: Esun PETG Notes: You may get away without using any supports. I haven't tried. I use Prusa slicer with paint on...

Its just the way the sprite has been designed by creality with the cable coming out the centre of the extruder. But this support causes way less kink than the original part and some others on here. 3. You do not have to trim back the locking...

Hot end ribbon clip for ender 3 S1

If you're struggling with a short ribbon cable for your X and E motors that can't be routed inside the chain along with the hotend cable, then this piece was specifically designed for you. Installation Notes ------------------ • Insert this part...

... damage anything but it can wiggle out of place. Going past 240 will wear your ribbon over time anyway and at that coordinate you are pretty much off the build plate with your nozzle, the only time you would want to go that far is for a bed mesh.

Both should work fine, but if the 0.8mm one offers a little more clamping force. I would suggest you just print both and use the one that fits best for your use case. You should print this in 0.2mm layer height for best dimensional accuracy. Print...

Two of them can be found in each standard printer roller used on Ender 3. ...I've sacrificed one spare roller and cut plastic on two sides to get them..Fusion 360 file is also available if someone wants to adjust it to its own needs or different printer...

I designed this clip as a replacement one for the Raspberry Pi. It should work on all models except for the Raspberry Pi Zero W. There are two variants for the clip, one with a thickness of 0.6mm and one with a 0.8mm thickness. Both should work...

A quick and simple fix for you Ender 3S1 series printer, which eliminates the stock issue where the ribbon cable crunches while homing. I took the basic concept off of Printables (user and product linked and tagged below) and custom made this...

... inserted in the guides (see pic #2) with this cable protector I don't have to. Plus I can slide the protector more easily up when I need to connect the ADXL345 mount.https://www.printables.com/model/213646-adxl345-mount-for-the-ender-3-s1 

This is a remix of this awesome Raspberry Pi Drawer https://www.thingiverse.com/thing:5201485 I added a slot for the camera ribbon cable and standoff type bottom so the pi can snuggly slot in without the need for screws or bolts. ...Obviously these are...

Furthermore, I adjusted the position of the ribbon cable attachment as it was interfering with the bottom LED strip holder. The new version of this part is included in this remix. ...To ensure strength, I printed all parts at 100% infill, which proved...

Enjoy this moment, buddy! ...For bulky wires that need some serious handling.