ender 3 psu 3d models

After looking for mounting brackets to relocate my Creality Ender 3 Pro PSU so I could put my printer inside the Creality enclosure, I decided to design my own. I needed brackets to be able to relocate my PSU separately from the printer so it didn't...

I wanted the pi to run off the Ender 3's PSU, and went for the USB powered route instead of hard wiring a buck converter. Here is the buck converter I used - https://www.amazon.com/gp/product/B07121W7Q4/ Others would probably work just as well, I...

PSU case for the stock Creality Ender 3 Chang Liang PSU Uses stock screws and works pretty well. ... Tinkercad link: https://www.tinkercad.com/things/gRCUonW58pc-cl-psu-cover-comp-v13/edit

This PSU silencer reduces noise from the PSU fan, while keeping the temperatures low! ...It was designed for ender 3 MAX, but might work for other models. ...The two screws are 7 cm apart.

The Ender 3's power supply unit (PSU) requires an external stand to elevate it off the ground and provide a stable surface for operation.

I have modified and shortened Hook3D PSU switch's STL and located it on the left hand side of the ENDER 3-Max. Also, I added 2 brackets to hold the PSU fan down to avoid all the debris from fan's suck in force. All you need is: 1. 4 X M4 to...

Alternative PSU Mount for the belt3dprinter.com Ender 3 Belt printer kit. On the beta version of the kit one hole for the stock PSU mounting location was drilled wrong. So in order to get on with testing I designed this right quick and now that I...

I loved the initial concept by dade75 (https://www.thingiverse.com/thing:3747148) but discovered the hard truth - the Ender 3 Pro ships with a unique PSU that refused to fit. ...I crafted this custom mount, drawing inspiration from his original design...

I wanted my PSU to be under the rear side of the bed like the Ender 3 v2 is, but looking at the existing mounts, they were either mounted so the fans were facing up or had no access to wiring and a tighter fit than I wanted. I designed this setup...

This print will allow for the PSU beneath the Ender 3 V2 to actually breathe. As stated in the Meanwell documentation sheet, the holes on the PSU are not to be covered by any means. So this print will do a great job of organizing the PCB wires and...

# Additional Hardware * 1x M3 bolt at least 6mm long for holding the two pieces together * 4x M3 bolts that are 4mm long to mount the relay board * Stock mounting bolts/screws for the power connector and power supply # Additional Notes Apparently,...

This model enables you to relocate your PSU on an Ender 3 Pro, making it easier to install a second Z lead screw and motor. Alternatively, you can use it to remove excess weight from your uprights. It optimizes air flow to keep the PSU cool. The...

The bottom of the PSU is approx 1/4" off the surface when the stock rubber feet are used. I recommend using a different type of feet to raise the whole printer off the surface. You will need extra bolts and nuts to mount. Simply remove PSU from...

... Remove plastic housing from PSU. Remove 3 wires from switch and run thru small square hole in back of switch box. Reconnect wires and mount switch box. Mount left and right supports to PSU, using stock holes. Then mount to structure. ... Enjoy!!

This part is designed to mount the power supply for the Ender 3 Pro (Meanwell LRS-350-24) to a leg of an Ikea Lack table. The legs of the table are hollow, so you can drill a hole behind the mount to run cables through. Don't forget to ground the...

This part is designed to mount the power supply for the Ender 3 Pro (Meanwell LRS-350-24) to a leg of an Ikea Lack table. The legs of the table are hollow, so you can drill a hole behind the mount to run cables through. Don't forget to ground the...

A remix of another fantastic design for attaching a larger (quieter) fan to the Ender 3 V2's PSU. I didn't need as deep of a shroud, instead using an 80x15mm fan (one from Arctic Cooler). As I am printing this in my dorm room, and want to avoid...

This is a PSU enclosure designed specifically for the Ender-3 Pro's power supply unit. This innovative design boasts numerous capabilities and conveniences not found in the original model. 1. The power cord is neatly routed back into the case. 2. 3....

Mod to remount your Ender 3 power supply. ... Requires: 4 x M4\*12 1 x M4\*8 1 x M3\*8 1 x M4 Nut

ABS 100% infill should hold PSU with one bracket. ...Please consider the print orientation.

ABS 100% infill should hold PSU with one bracket. ...Please consider the print orientation.

And as I wanted to replace the old PSU with the LRS-350-24 PSU from Meanwell, this asked for a redesign (o;It is advisable to have a protective ground cable attached to the PSU and the back of the profile as the supplied mounting angle for the PSU...

Lüfterlose Netzteilabdeckung mit Namensschild. ...Könnt ihr euch gern mit einem Namen benennen und dann Drucken. Läuft bei mir seit mehreren Wochen ohne Probleme. https://www.tinkercad.com/things/kPpW0TWw9dd Ender 3 - Großes Meanwell Netzteil

... expoxy. As a bonus I added a link of @johnniewhiskey Ender 3 Cable Chain to the last part so it sits below the power switch REMEMBER: You'll need some new printer feet to raise your printer at least 40mm https://www.thingiverse.com/thing:4685161

This is a cover that I made for the power supply of the Ender 3 V2. It is made for a 92x92x14mm fan, for example NOCTUA NF-A9x14 PWM It replaces the black cover of the printer and the cover of the power supply unit must also be removed. ... The...

I wanted to remotely mount my PSU for my Ender3 and all of the other mounts had them orientated flat against the bottom of the tables and I didn't want to hinder the airflow. There is enough room for the wires to come out of the bottom as well as...

... INSTALL NOTE: When installing this product, countersunk 4x8mm screws are embedded in both the top and leg sections. Secure the brackets to the PSU before proceeding with mounting. ...I opted for 5x20mm screws when attaching it to the enclosure.

One more note: The Meanwell PSU's fan seems to blow down, into the PSU, towards the circuitry and out where the wire connections are made/the bottom. ...I flipped the fan so it sucks through the bottom instead and blows out the hole as it seems to have...

Also, I updated the PSU fan to a 92mm version, a remix of 3570785 from SilliCone. This baby's got it all: a 9225 DC 12V 2Pin 92mm x 25mm Brushless Cooling CPU Cooler Fan and a CPU Cooling Fan Cover Iron (90mm) to keep things chill. And let's not...

I remixed this excellent idea to accommodate 2 changes: 1: Flipped the PSU so vent slots and fan are facing downward. This is only feasible for printers that have riser feet that introduces space underneath the frame (see thumbnails). Without that...