ender 3 psu 3d models

All the mounting hardware that comes with the Ender 3 is designed to be installed right onto the top of the power supply unit, utilizing the screws already in place on the PSU itself.

Fan shroud assembly to allow the installation of a 80x80x10mm fan on the power supply of a creality ender 3. Installation requires removing the old fan and drilling a few new holes in the metal cover of the psu. ... Wire for the new fan can be run...

Designed specifically for the Ender 3, this modification redirects airflow away from potential heat sources, ensuring a quieter printing experience. I installed it without any prior knowledge of PSU airflow or heat generation, so use at your own...

##80mm PSU cover for the original Ender 3. It prints in to parts. The fan screws on to the PSU Cover and the Fan Cover screws on to the fan afterwards. The Fan Cover is optional but i think it looks good :) The model is designed in Fusion360...

This is a bracket used to stiffen up the regular Ender 3 frame by clamping the freehanging end of the PSU to the frame.I originally designed this specifically for my own printer and therefore didn't add any oblong holes or other means of adjustment.

This is a specially designed tool holder to keep all printer tools and six needle files, three flat and three round, neatly organized on the Power Supply Unit (PSU) of the Ender 3.\r\n\r\nIf you have any other custom design ideas, feel free to leave...

... Thingiverse with ID 3130768. ...This custom component reroutes airflow from the power supply unit (PSU) out the back of the printer, significantly reducing noise levels. Engineered specifically to accommodate Ender 3 printers. ...Use at your own risk.

Ender 3 power supply (Chengliang CL-P360W24V) cover with SilentiumPC Zephyr 7015 (SPC013) fan. The fan is cheap (cca. $5) and quiet (17.7 dB). It fits inside the PSU. The original fan is 24V but the new one is 12V. I'm using 100 ohm 2W serial...

i changed the mount so it mounts on the side of the psu to the wall, rather then the back to the wall this is a remix of https://www.thingiverse.com/thing:3747148 ENDER 3 MAX VERSIONS PRINTING. https://youtu.be/Oc7JB86vo0g (bottom) ( time lapse ) ...

To complete this upgrade, I followed an instructable guide specifically tailored for replacing fans on Ender 3 printers, which can be found online at https://www.instructables.com/id/Ender-3-Silent-Fan-Replacement-Guide/. ... The new fan was purchased...

Verified compatible with standard Ender 3 power supplies, but its usability on pro models or other printers remains untested. Additionally, a gap has been incorporated to accommodate any necessary wires. ... I use it in conjunction with my cpap...

I'm trying to avoid buying new fans for my Ender 3, so I've been searching Thingiverse for a simple and silent fan duct to keep my PSU cool. After not finding one that met my requirements, I decided to design one myself. This custom fan duct allows...

On my ender 3 I have the PSU cover that moves the power lead to the back of the PSU, there was enough clearance initially but it has caught the rear right levelling wheel a few times, knocking the bed out of level and was hitting the glass bed so i...

--- THIS IS THE SAME AS THE ONE I MADE FOR THE ENDER 3 MAX ---ONLY SIZED TO FIT THE ENDER 3 -— Pic is of model installed on ender max . have not done a test print for my ender 3 of this model. so please check size before printing to confirm it fits.

PSU cover for **Creality Ender 3 Max**. I think it fits multiple PSU's from Creality. Replaces both the PSU metallic cover and the plastic housing for the power button and power socket. Reuses the factory screws from the metallic cover. As stated...

To make my Ender 3 a little more silent i tried one of these PSU fan ducts. Even if they are called "silencer" it made it even louder cause the air has to be pushed throu the duct too and that makes some noise. So i decided to just move the fan from...

For fastening it I used 2pcs M4x16mm screws with washers and hammer nuts. Measurements: PSU size: W50xL113mm Fastening holes: 2x4,2mm Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: Doesn't Matter Supports: Yes Resolution: 0,20mm...

This is a custom cover for the stock Ender 3 power supply that adds a USB socket to power a Raspberry Pi running OctoPrint. It also includes a divider between the mains AC section and the low voltage DC section of the cover, as well as a mount for...

... ------------------------------------------------------------------------------------------- A simple print cover for the PSU of your Ender 3, inspired by the Oranginator cover, which I re-sketched from scratch to gain better control over this part.

I do not take any responsibility for harming or destroying yourself or your 3D printer during installing this mod. 7.10.2020 Removed mounting holes on the top. Added Fusion360 file. 7.9.2020 PSU cover with mounts for any 120mm fan using stock...

Very simple power supply cover for Ender 3 (common version not version for) using the 8010 fan

Very simple power supply cover for Ender 3 (common version not version for) using the 8010 fan

I create this for support my PSU which use side frame as locking attachment.

Made a fancover for this wonderful PSU Cover for 60x60x25mm fans. ... My first model :-)

If I get enough requests I can make another version that uses the 3 screw located on top. Don't make copies of my design but feel free to remove my logo on the back for your own personal use. I'm sharing because I know there are others out there...

... make sure to check if the bed collides. **Hardware:** * 4 x M3x8mm caps * 4 x M3 T-Nuts * 3 x M4x8mm buttons # Changelog: **16/05/2019:** Expanded slot size for better adjustments. ...**08/05/2019:** Added slots to allow for improved positioning.

WIP! ...Project require a lot of edits. Do not print! Update 29.05.2022:- Added case cover mount holes- Added cable tiers holderUpdate 28.05.2022:- Added PSU switch cover model for compatibility with PSU legs

Another PSU cover but with place for integrate a LM2596S. ... I use the LM2596S for replace the original psu fan with 120mm fan (12V) (https://www.thingiverse.com/thing:3735282).

Tired of all the over engineered PSU brackets that take way to long to print ? I designed these simple brackets that print in little over an hour each. There is a gap between the PSU and the table due to airflow. ... I added an extra ground cable from...

... an hour each, making them a quick and efficient solution. The gap between the PSU and the table is intentionally left for airflow purposes. To ensure maximum safety, I've added an additional ground cable from the printer frame directly to the PSU.