ender 3 psu 3d models

Fits a Noctua A9-14 (4pin) 12v fan - 92x92x14mm Original PSU fan had a 74dB peak noise level (as measured with my potato) After the mod the psu peak noise is 51dB (measured with the same potato). Support: YES. (there's a small piece in the corner...

Remixed version of this to fit Ender 3: https://www.thingiverse.com/thing:4405355 See the original version for the parts missing (top, LCD etc) Because of the fact that i only have a skr mini e3 and a rpi 3b+ i cant remix other versions. Changed...

It fits my 100mm ultraslim and low noise fan outside the PSU box perfectly. I've done everything with a honeycomb surface for better cooling. With this cover, even without a fan, the power supply works very well, and the fan will rarely turn on. No...

Moreover, relocating the power cord also meant sacrificing one of the screw holes used for securing the case to the PSU, but given its non-structural nature, I deemed it acceptable. I discovered that utilizing tree supports in Cura proved effective...

https://www.thingiverse.com/thing:4441076 presented a thumb screw to replace the wing nut on the front-left corner of the BIBO bed. It is too wide for the other two positions. I have created a smaller version to fit the right-front corner and the...

Remixed drshats mount because it didn't leave enough space for well...anything. Have not printed and tested this yet as of 5.15.21. ...Really quickly mocked up in TinkerCAD

modified the holes in order to fit a 120mm fan. might have to dremel holes a little bit after. ... This is a remix from https://www.thingiverse.com/thing:398515

No more audible noise from the power supply! I made some adjustments to ensure that the angle of the fan supports matches perfectly with those of the cover - no reprints needed. If you happen to print out this design, would you be kind enough to...

I added another set of holes for another zip tie and added a rounded corner for a more even look.

I added another set of holes for another zip tie and added a rounded corner for a more even look.

I ordered the the A9x25 instead of the 14, so instead of re-ordering I thought I would adjust this cover so it will fit. ... I did use the original cover as a stop gap by cutting away the fan shroud on the top and press fitting it through as I had...

Finally, complete silence from the power supply is music to my ears. I made the necessary adjustments to the fan support angles to perfectly align with those of the cover, but I didn't reprint it yet. If someone does print this piece for...

The original Model was very good and I wanted to use for my mod, but I was missing the grill for the fan, so I made this remix with a grill, so that no big parts can possibly enter the fan.

ATTENTION!! in my case, i had to invert gnd wire (black) with 12V wire (red). ... (in the original fan the cables are reversed) fan 60x60x25 noctua fan grid https://www.thingiverse.com/thing:4699982 35 mm feet feet:...

I was inspired to remix this after the flap broke off when trying to remove supports Replaced the flimsy flap with two short parallel rails, corresponding to the original footprint of the flap, with a set of cable tie anchors The result is a...

I designed this addition to minimize noise pollution from my printer's power supply, but unfortunately, it didn't yield significant results. I found inspiration here: https://www.thingiverse.com/thing:3328495, but I created this entirely on my own,...

Remixed to accommodate my files and tweezers

Replace the original power supply cover with one designed specifically for an 80mm fan. ...I opted to use a 12V fan connected to an external (plug-in) power adapter, as quiet 12V fans are significantly more affordable than their 24V counterparts, and...

<p>Optionally can be secured using an M4x8 screw.</p>

Just print it and use it

Check it out in action here: https://youtu.be/4jk6kZIwsQA

Small part to cover the main voltage wires. Fits to the Meanwell Powersupply cover like this. ...You dont' need the metalpart with the fanguard.

Small part to cover the main voltage wires. Fits to the Meanwell Powersupply cover like this. ...You dont' need the metalpart with the fanguard.

Tweaked the existing cable cover from https://www.thingiverse.com/thing:4822648 in order to trim a little excess, add some wiggle room for the bolts and remove the need for supports. I had trouble fitting the original due to fouling on some custom...

This is a Remix from https://www.thingiverse.com/thing:4794712 i made it to put a 80 mm Fan.

This Ender 3 PSU Silencer incorporates a handy holder for the 38mm spatula that comes with the printer. I wanted to create this because I needed both a holder and a silencer. ... The design is for Ender 3 Pro, the screw hole distance is 70.70mm.

This is a remake of Ender 3 Pro PSU Cover honeycomb 80mm fan https://www.thingiverse.com/thing:4082992 from IDDQD-. I've modified the bristles around the cover and removed the screw holes. With this, the cover becomes sturdier and fits more PSUs...

Offset for Ender 3 PRO PSU to accommodate dual Z stepper Print : 0.2 height 4 walls 40% infill This should fit like a glove, unless your printer is really badly calibrated. The screw recess is 2mm deep, in some cases the original set of screws may...

This is a remix of [mfau's](https://www.thingiverse.com/mfau/about) ["Ender 3 PSU cover with USB"](https://www.thingiverse.com/thing:3225570) fitting the Ender 3 Pro power supply (Meanwell LRS-350-24). I wanted to fit this cover on my Ender 3 Pro...