ender 3 prusaslicer 3d models

 Prusa Printers doesn't allow attaching Fritzing FZZ files, so let me know in comments or a message and will see about putting up a cloud drive link.The following pushbutton switch colors and their corresponding connection on the Adafruit Trinket M0...

3 of these would be used in a frame that would fit the Sterelite Gasket box I used (about 300mm long.) They would slide under the aluminum square rods from the front and should not interfere with the filament. The back and front of the trays would...

Commodore PET Replacement Keyboards (under construction) 1) "SK" Keyboard Shell 3D Models 2) "SK" or Business Keyboard 3) "GFX" or Standard Keyboard The Commodore PET is a part of computing history, one of the "trinity" of home computers from 1977......

It will be cheaper and more accessible.I'm pretty sure in time acrylics suppliers from the US/EU and other countries will be recommended by community members and I'll add them to the recommended list here.so the simple answer is: Get the panels from...

After testing these rotors I found that they all work and they worked best when paired with the alternate horn instead of the default horn, I think my current recommendation will change to the rotor with the 3.6mm cone diameter paired with the...

Print with nut insert" /> Electronics Tools • Accessories Hand Tools Power Tools &bull; Accessories <a href="https://www.thingiverse.com/thing:3837220"...

Print with nut insert" /> Electronics Tools • Accessories Hand Tools Power Tools &bull; Accessories <a...

Print with nut insert" /> Electronics Tools • Accessories Hand Tools Power Tools &bull; Accessories <a...

Print with nut insert" /> Electronics Tools • Accessories Hand Tools Power Tools &bull; Accessories <a...

Print with nut insert" /> Electronics Tools • Accessories Hand Tools Power Tools &bull; Accessories <a...

Print with nut insert" /> Electronics Tools • Accessories Hand Tools Power Tools &bull; Accessories <a...

This is additionally fixed with a little super glue.Do the same with "Lamp DuoLux_tubeleft.stl".3. Assembling Light Units</strong></p><figure class="image"><img...

http://www.thingiverse.com/apps/customizer/run?thing_id=53235 Instructions Using the following options: gammaTooth = 2.3125 MusicCylinderName = new song axisSlack = 0.6 midBigTeeth = 21 pulleySlack = 0.45 gear_gap = 1 snapAxisSlack = 0.3...

Wiggle the ends of the sails and gently press the top of the mount against them until everything slides into place:Step 11: Now connect both halfes of the sail mount using 3 screws:Step 12: This is the most satisfying part of the work: Thread the...

WARNING: The current version might have the Stealthburner bump into it at max travel points (not in regular printing...

This is great for students to play in between classes, or during break, or anyone who loves a nice chess match. The approximate dimensions of the chess/checker set when rolled up is ~3.5in ø (~86mm ø) x ~ 8in (~204mm). Weighs ~453g (~16oz). This is...

This pack contains over 3,000 Christmas decoration STLs generated from the top 3000 first names in the USA. The pack also includes PNG renders of each Christmas decoration. The decoration is 60mm in diameter. For long names the width may be wider.

http://www.thingiverse.com/apps/customizer/run?thing_id=401429 Instructions Using the following options: pattern_size = 10 pattern_clip = 95 pattern_copies = 20 pattern =...

Let's see poor Kevin in the following videos: For Part 1 in PLA please go here: https://youtu.be/ErP28uP4mVI For Part 2 in PLA please go here: https://youtu.be/LlN01EW9ORI For Part 3 in ABS please go here : https://youtu.be/feWsPd2XUFU For Part 4 in...

The boxes are designed to stack such that multiple units will share the same equivalent height; for example, 3 x 20mm (1U) boxes, will share the same height as 1x50mm (3U) units. ...Any combination can be true if the total Unit height matches across...

I used a Prusa 3 to make this so some of these recommendations may not work quite the same with another printer, but I describe what I did here. I used PLA, and the layer height was set to the default 0.15 mm. And for the one part where I used...

On the bottom of the base, there is a access hole to the IR detector; use this access hole to push the IR detector out through the hole in the base (a pair of needle nose pliers helps with this).[3] Prepare LED StripThe "internal length" of the...

This is the part used: "2.4" 240x320 SPI TFT LCD Serial Port Module+3.3V PCB Adapter SD ILI9341" You will need 4x 3mm wide (m3) x 10mm screws to hold the upper &amp; lower case together. I use m3x10mm Thread forming / self tapping screws because all...

PETG seems to work well and allows for some flex when turning the screw.”I, personally, used PETG and it worked just fine but I guess PLA would also work.You should print it upside down (the ball support upside).I used 0.15mm quality settings in...

It took nearly 3 weeks and a couple dozen fundamentally different designs before settling on the current GateRodders design for SC17. A NOR gate is fundamentally a NOT gate imposed on the output of an OR. The input and output rods are trapped...

Notes: - I printed all the parts lying down with supports and the panels seem strong and turned out pretty well - I left the supports on the body panels to add strength and to provide a surface to mount inside panels like the old school vinyl on...

Since we wanted a flying model it made sense to see if we could build one of the earlier Titan II concept vehicles due to its large fins. To begin we had a scale 3-view drawing from the original Dyna-Soar/Titan II design by the Martin Company. This...

Note: position the inner filament end such that it is centered between two spokes:3 - Mount the first hub ring:4 - I turned the spool around because the filament end was on the bottom:5 - Insert the inner filament end into the dedicated hole in the...

I crimped these two leads into a 3-pin Molex KK plug and plugged this into the E1 slot on the Duet like this: Note that only the red and black leads are connected to the board while the white lead is cropped (a little hard to see in the photo) since...

3) There are many issues with the current design that needs addressing in the next iteration. I’m only a beginner in electrons, so there will be design flaws. The device is not a 50-ohm impedance match, so there will be signal loss within the design...