ender 3 pro z axis knob 3d models

I also wanted a no nonsense knob for my Z-axis. It's a tight fit so this has been working great. I have been printing coarse at .3 with the worst ABS filament (NOVAMAKER) and most of the stuff I have been developing comes out flawless. So, at...

This is a remix of the Ender 3 Control Knob by echoffmann, I made it so that way the divot in the middle of the knob was completely flat for better printing

A filament guide is necessary to use the knob on the Ender 3 and have the spoolholder on top. FIX (02/10/2018) Thanks to user wonkoderverstaendige I found out there was a tiny but real problem with the file. Basically the knob floated a mere...

A filament guide is necessary to use the knob on the Ender 3. *FIX (02/10/2018)* Thanks to user <a href="https://www.thingiverse.com/wonkoderverstaendige" target="_blank">wonkoderverstaendige</a> I found out there was a tiny but real problem with...

A simple and small control knob for the Ender 3 and Ender 3 Pro. PRINT SETTINGSNozzle: 0.4 or 0.6Layer Height: 0.20 or 0.3Infill: 20% Supports: NOMaterial: PLA+

This is my own take on a Z axis Belt Mod for the Ender 3 / V2 / Pro. it is based on the Voron 2.4 Z axis gearbox and extensively modified to work on the ender 3 platform. this is for use with duel z stepper motors and linier rails. other additions...

This is an adapter wheel for the Ender 3 Pro, designed specifically to accommodate a stepper damper mounted on the Y-axis. When installed, the diameter of the wheel measures 47 mm, which is significantly smaller than the standard 60 mm diameter found...

You should probably use a drill press for this since it requires more accuracy.On my quest to print at very high speeds on my Ender 3 Pro, I noticed some room for improvement in the Y axis mechanics.The V rollers were inconsistent and unreliable, the...

Hier ist meine Halterung für einen optischen Endstop der Z-Achse auf einem Ender 3, Ender 3 Pro, vielleicht auch Ender 3V2 Der Sensor wird mit M4 Einschmelzhülsen befestigt. ... Die Hülsen findet Ihr hier: ...

A remix of a Kirby Amiibo with a hole cut in the base to fit the extruder motor stem to fit an Ender 3 Pro.

The Ender3 Pro requires the inversion of axis Y to be activated. ...To utilize screws from the X-axis endstop cover plate, a gasket has been made for length compensation.

"Remix" to include different thickness .stl files. Print Settings Printer Brand: Creality Printer: Ender 3 Pro Rafts: No Supports: No Resolution: 0.16 Infill: 100% Filament: Generic PLA Any Post-Printing ============= Mount instructions (same as...

I was unable to find any existing designs for an enclosure for the Y-axis pulleys on the Ender 3. This is Revision Two of my design, which is still in progress. I need to make some adjustments to ensure there's enough clearance above the idler pulley...

As requested by Printer Let, here's my version of the Y tensioner for the Ender 3 Pro with a 40x40 V-slot Profile. Update: October 8, 2019 Fixing System: 2 M4x8 screws 2 M4 T-nuts Updated models to the Mk7 Version, compatible with all different...

As requested by the user Printer Let, here is my version of the Y tensioner for the Ender 3 Pro with 40x40 V-slot Profile. Update of October 8th, 2019: Fixing System: - Two M4 x 8 screws - Two M4 t-nuts Updated the models to the Mk7 Version,...

I was not satisfied with the available Z-endstop mounting options for the Ender 3 Pro. I have been using https://www.thingiverse.com/thing:2816718 on my CR-10S and it works great but cannot be used because of the differences between the y-axis motor...

It is possible to attach heatsink to the motor if worried, or if you have attached the All In One case on the back side of your Ender 3 Pro, you can direct the air up towards the motor instead of down towards the floor. The mount is assembled in the...

This is a Bender knob for the Ender filament sender that I made in September.

**It only fits the Ender 3 Pro with a 4040 center extrusion.** This bracket is needed because some Ender 3 Printers are shipped with pressed pulleys on the stepper motors. Those pressed on pulleys can't be adjusted along the shaft of the motor. All...

The knob is useful to manually move the Z axis when the stepper motor is disabled or to visually check Z steps during the print In addiction to look cool, since this design has flat edges there is no risk for the filament to be catched in the knob...

The knob is useful to manually move the Z axis when the stepper motor is disabled or to visually check Z steps during the print In addiction to look cool, since this design has flat edges there is no risk for the filament to be catched in the knob...

Guide the Z-axis for your Ender 3 series or CR-20 with precision using a bearing 608Z. ...This updated setup has no impact on the maximum print height of your Z-axis, so feel free to create towering prints without restriction.

... rafts and supports to ensure stability, but they proved to be a frustrating challenge to remove. I also encountered difficulties threading the Z-axis adjustable knob, which exhibits slight misalignment, yet its imperfection does not bother me.

Found an Oreo or Benchy knob you want to use on your Ender 3 or Ender 3 Pro but it's made for an Ender 3 V2? Look no further than this simple adapter piece. This adapter can be super glued into place, I personally didn't have any on hand so I just...

This replacement knob is slightly larger than the standard Ender 3 Pro or Ender 3 knob. If you have any questions, comments, or concerns about this product, feel free to leave them in the comments section or email me at connordesigns26@gmail.com.

The Creality Ender 3, Ender 3 Pro, and CR-10 Extruder Knob are highly regarded components for 3D printing enthusiasts. These extruders offer impressive performance and reliability. With a focus on precision and ease of use, they cater to both...

I was not satisfied with the available Z-endstop mounting options for the Ender 3 Pro. I have been using https://www.thingiverse.com/thing:2816718 on my CR-10S and it works great but cannot be used because of the differences between the y-axis motor...

Hi, Dual Z bracket/mount for Ender 3 / Ender 3 Pro, (for use with anti backlash nut, mounted at the bottom) no need for extra hardware. ...The screw mounting hole is at exactly same level/height as original one on the other side ;-) enjoy Print: 0.2...

Hi, Dual Z bracket/mount for Ender 3 / Ender 3 Pro, no need for extra hardware ;-) enjoy Print: 0.2 height 4-6 walls 40% infill support: YES Position on bed: As shown on a picture Offset bracket for PSU https://www.thingiverse.com/thing:4610070 Z...

I'm a big fan of the original dial on the Ender 3 Pro Display, ...but I detest having to turn it dozens of times just to get what I want! =) So I came up with this nifty extension to keep the dial but speed up turning it. ...(Prusa-style) ENJOY, SAVE...