ender 3 pro z axis knob 3d models

Optical Endstop for Axis Z. ... Optical sensor with inversion and large (6mm) distance between transmitter and receiver: https://aliexpress.com/item/-/32728213054.html Additionally needed: Additionally needed: M3x12 bolts - 2 pieces for sensor...

This is a simple design to make possible to change the motor distance from frame so it's possible to properly align the z-axis/leadscrew I suggest using ABS because the motor will get hot and may deform the PLA.

This is a simple design to make possible to change the motor distance from frame so it's possible to properly align the z-axis/leadscrew * I suggest using ABS because the motor will get hot and may deform the PLA.

I upgraded the printer's drive system with a new z-axis drive for enhanced stability. The lead screw for this axis is notably long, as evident from the attached photo. Initially, I had planned to shorten it, but then I opted to add a die on top...

My printer has these Z-motor spacers installed and it is a perfect fit.Post-PrintingPress in a 608 bearing and attach to Ender 3 with (2) M3 or M4 screws and (2) t-slot nuts.Note: The oddball phillips hex washer M3 screws with a shoulder in the photo...

A compact z axis floating bearing without magnets. Uses 8 balls 2.2-2.4mm dia. balls (from a 16x8x6mm bearing) 1. Print all four parts on the flat sides. 2. Use sand paper to smooth the top printed surfaces which mate with each other. 3. Use...

... the extra spacing material that Alloca added to their specific setup, and repositioned the mounting holes to match the original design by Hangtight. It should work just fine on a stock setup, assuming your z-axis nut mount isn't way off center.

I designed this pin to give the z axis something to "park" on, away from the bed surface, while the printer is off and the stepper is not keeping it elevated. It goes into one of the unused holes from where the E3 / E3Pro vertically mounts the...

I've also moved to a top-mounted, double lead screw, design (https://www.thingiverse.com/thing:4569498) so do not have a need for this z-axis motor mount any longer. This is a remix of a remix created by Alloca. Original motor mount design by...

I fitted the cable chain to my extruder and z-axis cables, but noticed immediately that the chain was tipping over sideways and jamming up occasionally. To prevent this, I designed a support system using Fusion 360 to keep the cables in-line with the...

Z-axis limit switch regulator. It has discrete adjustment with a step of 0.025 mm. Printed from PLA with 100% coverage. The dovetail, after a short grinding and lubrication with grease for plastic, moves without play and effort. Bolt or hairpin Ф4...

it is in fact 12.12mm where it mounts to the upright, but 11.9 where to countersink heads are, meaning the flat surface where the motor mounts to is in fact at an 90.6 deg angle to the uprights, which is why the z axis bar is tight as it get down...

No supports needed.I based my design off a photo I saw of another Ender 3 with a similar cap, but I could not find the model. So here is my version. ...CURRENT PART RIGHT NOW ONLY WORKS WITHOUT A CR OR BL TOUCH, DO NOT USE THE CAP FOR ENDER FILE FOR...

Fine adjustment for the z-axis on the Ender 3 pro 3D printer. ...You aill also need a 5x35mm screw and nut.

New version (V5) of my chain mount to NEMA stepper motor on Z axis. Printing: When I print this, the orientation on the printing bed is best with the chain side facing up and the cable hole on top. The first versions weren't strong enough with 20%...

I'm using BMG clone extruder and the cable guide from llueen can't be fit directly - Z-axis brass nut blocking part of the guide. I have to remove some parts to get it fit. * llueen cable guide: https://www.thingiverse.com/thing:4723800 Also,...

New version (V5) of my chain mount to NEMA stepper motor on Z axis. Printing: When printing this, the orientation on the printing bed is best with the chain side up and the cable hole at the top. The first versions were not strong enough with 20%...

I was fixing my OG ender 3 and cracked the plastic mount that came with my printer, hope this will help others with the same issue. ...May need to use super glue on the threads of the circuit board screws if they do not catch into the plastic, 20%...

I recently upgraded the printer with a double Z-axis consisting of a lead screw and a stepper motor, and later I also added a timing belt so that when the stepper motors are disabled they do not go out of sync, but the first time I put a 610 belt on...

I'm adding a second Z stepper motor/screw thanks to the Dual Z Axis Ender 3 / 3Pro by CR83D Since I'll be using direct drive extruder I no longer need the original part with extruder mount. In my case it was bent uneven, so the 3d printed part...

A small modification to use another kind of screws. Screws M3 6mm : https://fr.aliexpress.com/item/32825015459.html Nuts 20S-M3 : https://fr.aliexpress.com/item/32825357262.html Print Settings Printer Brand: Creality Printer: Ender 3 Category: 3D...

Y axis cover for Ender 3 Pro. ... Works great with: T-nut M3 drop-in rotating V-Slot by DaVinci2000

I've just increased the slot size to perfectly accommodate the Ender 3 Pro's Y-Axis requirements.

This is a part for ender 3 that extends the bar at a angle that way you dont lose space when you get a direct drive extruder like the microswiss direct drive kit. Is also useful if you just need to maximise your print volume. It can be angled twards...

I crafted a custom Z knob that makes tweaking the Z position and monitoring Z rod movement a breeze. To enhance usability, I extended the knob's length so it sticks out above the top bar, making it easier to access and manipulate with precision. ...This...

Cable Bracket for use with the Teaching Tech rear controller box. https://www.thingiverse.com/thing:3688967 Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: Doesn't Matter Supports: No Resolution: 0.2 Infill: 15% Filament: NA ABS...

This is a part for ender 3 that extends the bar at a angle that way you dont lose space when you get a direct drive extruder like the microswiss direct drive kit. Is also useful if you just need to maximise your print volume. It can be angled twards...

Z-Bracket Spacer for Ender3 Z-Motor helps with making straight big bolt :D Its just 0.5 milimeter but made my big z-bolt perfectly straight and parrel to the frame. Happy priniting and u can print in in highest possible quality its just 5 mins of...

The components required for this project are as follows: - nema 17: a motor size specification, specifically a 34 or 40mm diameter - lead screw: an T8, P2, L8 screw with a nut attached - coupler: a 5 x 8mm device used to connect the motor and lead...

Ender three users now have access to a robust rear support system that provides unparalleled stability and reliability during printing operations.