ender 3 pro user manual 3d models

Guide for Ender 3 Pro, I wanted to design my own, so I'll share it with those who haven't found happiness among the many already existing ones. No support is needed, The axis goes in quite easily, just a little tap and it settles firmly into place....

I would advise against making these solid, they need to be flexible so you can twist / bend them around the existing hub on the ender 3 pro. (I tried one and snapped it) hollow works well. Takes about 30 - 40 minutes to print each one, two...

You will need to print two Tool Box Clips in order to attach the box securely to the Ender 3 Pro's bottom frame. The clips slide onto the box and then fit snugly into the bottom rail (you'll have to remove the back end cap from the frame first). ... ...

- JST ATTACK - Eurekaled LED CHANNEL WITHOUT ANY MODIFICATION TO THE PRINTER, I MADE A LIGHT FOR THE ENDER 3 S1 PRO. TO BE PRINTED 2 PLA ARMS WITH PRECISE FITTING TO ACCOMMODATE THE ALUMINUM LED TRUNKING. YOU MUST ALSO PRINT 4 ELEMENTS, ALWAYS...

Ender 3 or (Pro) Printhead Fan, selfmade Printhead, !!!!!!!!!!!!!!!!!!!!!!!!!! will only work with linear guide on X Axis.!!!!!!!!!!!!!!!!!!!!!!! Also you may have to rename it and get rid of the ä. Many printers dont like them :D Partcooler...

You will need to print 2 of the Tool Box Clips in order to mount the box to the Ender 3 Pro bottom frame. The clips slide onto the box and then slide into the bottom rail (you'll need to remove the back end cap from the frame first). I recommend...

While going through the journey of getting the most mods and upgrades possible for my ender 3 pro, I've discovered a neat little filament guide. The thing that sold me was that the guide actually had a roller in order to release the stress from the...

Ender 3 Pro spooler with 50mm and 30mm sleeves helps manage different filament spools efficiently. A nut keeps the spool straight, preventing twisting issues. To assemble this spooler, you'll need to print two nuts: one for the inner part of the...

Just a simple upgrade for the ender 3 pro wiring to the main board. This is intended to be installed into the slot that is machined in the aluminum extrusion base. I created this after getting annoyed with the heated bed cable set not having...

I designed a scraper/spatula holder specifically for my Ender 3 Pro printer, which fits neatly into the rails on the bottom left side of the machine. To install the holder, you need to remove the control box and lift the printer at least 7mm to clear...

This spool bushing is used to guide the filament spool on the stock Ender 3 Pro spool holder (no modifications required). It allows a clean and concentric rotation of the spool during printing. The bushing is held in place using 2 inserts that allow...

This design serves as a mounting bracket for the Y-axis support of the Ender 3 Pro and is compatible with the articulating mount for the Pi Camera referenced below. No additional screws, bolts, or hardware are needed to secure this mounting bracket...

You are still more than welcome to print these files yourself and i wont be taking them down Remixed set of dual drawers for the Creality Ender 3 Pro (here: https://www.thingiverse.com/thing:3416444 ) with inspiration from the Ender 3 drawers made by...

*** NOT DESIGNED FOR ENDER 3 PRO. DIFFERENT AXIS BARS***. ***PRINT CASE ON ITS BACK WITH NO SUPPORTS*** ***DRAWER IS PRINTED UPRIGHT*** Features: -Designed from scratch. - Simple rectangle. Print your own inserts? -Compatible with most...

This is an electronics case for Ender 3 Pro designed specifically to support any internals. The base has a hole mesh pattern so that boards and cables can be attached using 2.5mm zip ties. The cases are symmetrical and are slightly smaller than...

My **Ender 3 Pro**'s extruder arm got a nasty groove cut into it from years of pulling filament through at an awkward angle. I printed up a replacement to tide me over until my aluminum upgrade kit arrives. Unfortunately, there's either too much give...

Double drawer that can be mounted without any disassembly or modification to the recent Ender 3 Pro printer. The body have been designed for quick print time and minimal usage of filament. The thin profile also makes the body slightly flexible for...

This cable clip is designed specifically for use with the Ender 3, and its intended purpose goes beyond merely holding display cables in place.

This clip is specifically designed to secure cables on the Ender 3, and its use isn't limited to simply displaying cables.

THIS IS A WIP - PLEASE READ This case is designed for the default 4.2.2 Creality mainboard that comes with the Ender 3 Pro. You will need to flip your mainboard so that the microSD card is on the bottom. I removed the adhesive cable tie thing under...

Feel free to resize the hole if they don't match.Print SettingsPrinter Brand:CrealityPrinter: Ender 3 ProRafts:NoSupports: YesResolution:Layer height 0.16 mmInfill: 20%Filament: Tianse PLA Silver Grey Notes: Print orientation: print it upside downI...

I was tired of having lots of electronics and wires all around the printer, so I designed a enclosure for all of the ender 3 pro electronics including a raspberry pi. I wanted to have the front of the printer full of drawers for tools and parts so...

I redesigned it from scratch and fit it for my Ender 3 Pro. It slides right on the side of the rails and fits all the tools that came with the printer. I added support on both sides of the rail so it would be more sturdy and less likely to break off....

Below is what the V2 files should look like in the downloads section: Ender 3 V2 Ribbon Cable Clip.stl Ender 3 V2 Power Supply Wire Clip.stl CE3_Ender 3 V2 Power Supply Wire Clip Single.gcode CE3_Ender 3 V2 Ribbon Cable Clip Single.gcode CE3_Ender 3...

The Ender 3 Spool Holder is designed specifically for the Ender 3 3D printer, ensuring a seamless fit and perfect alignment with your machine's frame. ...With its sturdy construction and adjustable mounting system, you can easily swap out spools as...

This is a PSU enclosure designed specifically for the Ender-3 Pro's power supply unit. This innovative design boasts numerous capabilities and conveniences not found in the original model. 1. The power cord is neatly routed back into the case. 2. 3....

Questa progetto c'entra, per adesso, molto poco con la stampa, in quanto prevede la realizzazione di una connessione che porti ad avere una presa di alimentazione con i 24V disponibili dall'alimentatore dell'Ender 3 PRO. Seguiranno successivamente i...

I'm excited about the enclosure design for my Ender 3 Pro. I experimented with leg extensions printed from someone else's model, but they didn't quite work out due to a wobbly stand - a concern with curious kids who tend to touch things they...

Designed this modification to prevent excessive wear on the wires passing through the aluminum extrusion frame on both Ender 3 and Pro models.\r\n\r\nRemove the access panel for the main board, which requires three bolts at the bottom and one bolt at...

Custom mainboard case for Ender 3 Pro with space for a XL4015 buck converter.The original mainboard case unfortunately leaves no room for additional parts so I designed this modification with an overhang to the front which gives place for a buck...