ender 3 pro support 3d models

- Support pour carte écran Bigtreetech TFT 35 E3 V3.0 (à imprimer sans supports) - Support déporté pour carte écran Bigtreetech TFT 35 E3 V3.0 (à imprimer sans supports) - Cover pour carte écran Bigtreetech TFT 35 E3 V3.0 (à imprimer avec supports) -...

A simple attachment designed to clip onto the Y-axis for added functionality.

it should sit just a hair higher than flush I designed this for my CR10s Pro V2 but it should fit any machine that uses the same type of framing, and dual T8 screws. the photos show the part printed in GiantArm clear PETG at 240c with 75c bed,...

Added better support for anyone using the stock stepper motor like I am and improved all clearances.

Modified OP STL to adjust fit and add structural integrity to areas where I noticed cracking after use. ...Edit fixed voids and added tree supports.

With the default print orientation, no supports are needed Needed Parts: Original screws, T-slot nuts, bearings 2 x M5 bolt - original tensioner bolts on beam 2x M5 T-slot nuts - original tensioner bolts on beam 1 x M4 16mm - Original bolt that...

3. At the bottom of each 4040 extrusion, slide the Left and right bottom mount plates onto the 4040 extrusion. Do not secure them yet. Slide them forward. 4. slide the undercarriages into place. The one for the right side is designed to be a...

This is a remix of 'Ender 3 V2 & Pro Silent Motherboard' by scaryPug Designed to fit Ender 3 V2, but will fit Ender 3 Pro also. This cover houses 60x15mm fan. ...

This is a remix of 'Ender 3 V2 & Pro Silent Motherboard' by TerraVestra Designed to fit Ender 3 V2, but will fit Ender 3 Pro also. This cover houses 80x25mm fan. An lm2596 mount with screw added, please make sure your lm2596 fits in this cover...

This is a remix of [Ender 3 V2 / Pro motherboard cover for 80X25mm fan (no support)](https://www.thingiverse.com/thing:4653994) by [scaryPug](https://www.thingiverse.com/scaryPug), which was a remix of [Ender 3 V2 & Pro Silent...

This is a remix of 'Ender 3 V2 & Pro Silent Motherboard' by TerraVestra Designed to fit Ender 3 V2, but will fit Ender 3 Pro also. This cover houses 80x25mm fan. An lm2596 mount with screw added, please make sure your lm2596 fits in this cover...

This is a remix of Ender 3 V2 / Pro motherboard cover for 80X25mm fan (no support) by scaryPug, which was a remix of Ender 3 V2 & Pro Silent Motherboard by TerraVestra. Designed to fit Ender 3 V2, but will fit Ender 3 Pro also. This cover fits an...

Fan duct for Ender 3 S1 You need 5015 fan, 3 m3 8mm. ...12.11.2022 UPADATE 4020 FAN

Hey there, I'm installing my dampers for my Ender 3 Pro and noticed I've got those pressed gear stepper motors. It appears Creality is using these on their new printer. The x stepper motor has a full height of 51 mm, while the y stepper motor...

[ScaryPug](https://www.thingiverse.com/scarypug/designs) designed a brilliant [80x25mm fan mount](https://www.thingiverse.com/thing:4653994) remix of the also great [Ender 3 v2 8010 fan housing/mount](https://www.thingiverse.com/thing:4549738) by...

This is likely one of the top upgrades you could do to your Ender-3. You can either buy a kit available online [like this...

Remix of the widely-used filament guide, specifically tailored for seamless integration with the Z-lead screw support that precisely aligns with the top bar's edge.

The filament guide contains a spherical bearing that is 100% printable. ...Print flat so bearing prints upward. No supports needed. ... Created this to serve as a filament guide and a suppert for the 8mm dia ball screw

Functional mix between #3584158 and #4336829

Combined the two designs to allow both the light bar, and the spool reposition at the same time.

Ender 3 Pro LCD Enclosure Raspberry Pi4 with camera cable, with integrated tree supports.

It requires minimal support - only in two places marker magenta on slicer screenshot. Same screenshot shows proper orientation for printing. It requires you pull only top left wheel off of the carriage and push in the spacer. The hook on the part...

Support for Logitech C270 camera on X-axis for Creality Ender 3 S1 and S1 Pro printers. I made this support because I've tried others several times and I never thought they were good. This one best suited my needs. In the photos, you will see...

This is a remix changing the magnet orientation in order that the magnet is facing the Touch Mi.

Hotend washer, this should be inserted between the PTFE fitting and sleeve tubing

I relocated my CR-10s Pro and there wasn't enough headroom for the spool to be sitting at the top of the spool holder mount. I modified Filament_thin_support.stl so that it can be fixed lower down the spool holder mount. Requires 2 x M6 Screws (at...

Support for filament sensor and ventilation in Ender 3 PRO extruder. I added the extra ventilation to avoid that, if there is a lot of retraction, the filament gets hot and breaks, especially in summer it happened to me a lot. The fan is in...

Mounting the filament guide requires a clear path on the Z-axis. ...Simply attach it with the spare parts provided with your 3D printer.

You're free to repurpose the leftover components from the printer as needed.

This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/1QmgUm9xzt2