ender 3 pro light kit 3d models

I just wanted my ender 3 to have some legs. ...Making them tall enough to place a spool of filament under the printer is a plus too.

buy this and ender website

I've been putting in some serious time working on an enclosure for my Ender 3 Pro, and I'm finally done with it. This enclosure is different from most others because it's still a single piece when combined with the printer itself. One of its key...

I made a quick holder for half of a Penn Ultra Blue Racquet ball https://www.amazon.com/Penn-Ultra-Blue-Racquetball-Ball-Can/dp/B002LGF9L6/ref=sr_1_6?dchild=1&keywords=Penn+Ultra+Blue&qid=1598666340&sr=8-6 This is all I had available at my local...

I converted my Ender 3 to direct drive so I decided to place a BME280 in the place of the extruder... ...It is meant to be used with a enclosure but anyways =D

Kit link : https://www.th3dstudio.com/product/ender-3-dual-z-upgrade-kit/ Assembly : remove the cap at the back Slip the first (smallest) support Closed the Rail with the second support Screw in the screws on each side of the power supply. Please...

Light bracket for Ender 3/Ender 3Pro (or anything that has a t slot and you want to mount a light to). ...This bracket is made specifically for this light ( https://www.amazon.com/gp/product/B09JBLLYHD/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1 ),...

I made this clip for holding the LED strip on the ender 3 pro nozzle cover for a better view while printing. Used a 12 V LED connected with a buck converter. ...The buck converter is placed under the printer.

I made this clip for holding the LED strip on the ender 3 pro nozzle cover for a better view while printing. Used a 12 V LED connected with a buck converter. ...The buck converter is placed under the printer.

I swapped out the Ender 3's gears for a direct drive setup, and next I'm placing a BME280 sensor right where the extruder used to be. ...The plan was to use it with an enclosure, but that's not necessary.

This bracket attaches a flexible light to the back of your Ender 3 and Ender 3 Pro. To attach it, tap four holes in the extrusion on your Ender 3 using an M5x0.8 tap. The large hole in the part is tapped to a 1/8NPT27 thread to allow the light to...

This accessory kit will put less strain on your 3D printer's motor.

You can check out the kit here: https://www.th3dstudio.com/product/ender-3-dual-z-upgrade-kit/. Here's a quick rundown of how I assembled mine: First, remove the cap at the back. Next, slip in the smallest support piece. Then, close the rail with...

https://www.youtube.com/watch?v=Q0weOgRkm-g Grab the incredible Creality Ender 3 at: https://fr.gearbest.com/3d-printers-3d-printer-kits/pp_1845899.html?wi00000&wid=1433363&lkid=16947089 Get the perfect voltage regulator at:...

E3 Pro Mini! If the file comes out huge, scale to 40% works good. ...I would like to see some makes!

Holder for a cutter, spatula and 3 files or screwdrivers

Harness for my flashlight on the Ender 3 printer.

The downloaded version even stated it was intended for an Ender3, suggesting that the Pro model has a distinct setup. Therefore, I decided to create this quickly, as it serves its purpose. This design consists of three separate components: a case, a...

... you prefer. I purchased mine from a local surplus electronics store, but this part appears to be identical (albeit much more expensive) at newegg.com. I also added a blue lit-up push button to my Ender 3 to control the light's on/off function.

update 6/8/22 So I made a front lcd screen that works with the ender v2 screen. It's larger than the front but it will work for me good enough. Hopefully this helps someone else too. I had to adjust the top 120mm fan items so I labled them the...

This design was crafted from scratch to accommodate either the Creality or MKS Gen L mainboard, alongside a Raspberry Pi 3. ...Additionally, it's optimized for two 80mm fans that stand just 10mm tall.

Light shroud for Ender 3 or Ender 3 Pro. Assembles by sliding into the bottom channel of the top extrusion. Uses WS2812 LED strips or any other 10mm wide LED Strips. It holds 3 rows of strips. I can fit 15 LEDs in each channel when using a...

Found this light at my local hardware store Bauhaus and thought it had the perfect length for a light on my Ender 3 printer: https://www.bauhaus.info/lighting/under-bench-light-beta/p/20082626?search=beta%206 Wanted to attach it with a little offset...

I designed a LED bar light with a 300mm LED strip attachable to the Ender 3. It is approximately a ~3 hour print @ 0.2mm layer height and is printed in 2 parts (left and right) before gluing together. Hope you find this print useful! ...Cheers and...

This light bar is printable on an ender 3. You need to remove the disallowed sections in the def file in Cura to allow you to print this. After that just turn LightBar.stl 45 degrees and center it, you need 3 mounts. ...Also, I used a 24V LED strip with...

This light bar is printable on an ender 3. You need to remove the disallowed sections in the def file in Cura to allow you to print this. After that just turn LightBar.stl 45 degrees and center it, you need 3 mounts. ...Also, I used a 24V LED strip with...

This is a straightforward hanging light stand that secures to the top rail of the Ender 3 printer.\r\n\r\nThe design draws from https://www.thingiverse.com/thing:3328378 for the v-rail insert.\r\n\r\nPrint this model on its side, and consider adding...

I couldn't find a light bar I liked for my Ender 3, so I made one. There are 2 different variations. The first not having holes for wiring and the other having them. I cut the wires on my light bar and attached them to the PSU, so it would power on...

The Maker's Mod to Make It Shine - A Lightweight Upgrade for the Ender 3

Summary This X-Axis Motor/Limit switch cover corrects the issue with the carriage that comes with the Creality Sprite Extruder Pro Kit. The limit switch using this is moved an additional 6mm away from the carriage, giving you bed space back. Screw...