ender 3 pro layer shift 3d models

I have printed several filament guides for my ender 3 but the end up broken over time so i decided to design an heavy duty filament guide that wont break. It's worth the effort. ... Very sturdy, no flexing or breaking.

This is a remix of https://www.thingiverse.com/thing:3676132/files designed to slide over the stock fan bracket on the ender 3 with my Volcano hot end. ... 4x m4 screws One of the screws holding the stock cooling fan on 60mm fan

The QuickSwap is a simple spacer designed to facilitate fast switching between the Ender 3's magnetic bed and the official Creality glass bed. It securely clicks into place, featuring a carefully crafted friction fit that eliminates the need for any...

Hello, here is another model from me. ...It is a direct drive extruder for Ender 3 and derived variants. The model is drawn according to the template and then fine-tuned to fit the X profile plates. ...Thank you, let it serve!

Camera mount for Ender 3 Pro 3D printer. It mounts to the Y Axis extrusion and works great for timelapses.Above timelapse was taken with this camera mount and an adapter to raise the camera a little higher for this print.Uses ¼-20 X ¾" bolt in the...

... Google Translator for help with translation. ;) Print Settings Printer Brand: Creality Printer: Ender 3 ProRafts: Doesn't Matter Supports: YesResolution: ≤ 0.20 Infill: ≥ 40% Filament: No brand PLA As you want Category: 3D Printer Accessories

I made this with a backplate that mounts to the original x-carriage plate of the ender 3 pro. All the holes are made to fit melt nuts so the m3 screws have proper grip (10 in total). I used m3x10 screw to assemble it. NOTE: This will bring your...

Camera mount for Ender 3 Pro 3D printer. It mounts to the Y Axis extrusion and works great for timelapses.Above timelapse was taken with this camera mount and an adapter to raise the camera a little higher for this print.Uses ¼-20 X ¾" bolt in the...

It is possible to attach heatsink to the motor if worried, or if you have attached the All In One case on the back side of your Ender 3 Pro, you can direct the air up towards the motor instead of down towards the floor. The mount is assembled in the...

Very practical for storing your ender's tools

... ___ ## ** Ender_Case_28x45.stl ** TL-smoother details: SIZE: 28X45mm **Notes** This model has not been tested. First, try to print the test model (TEST_HOLDER 48x25.stl) to verify that the module fits. ...Then proceed with the full housing print.

Follow word doc instructions or reposition ABL using provided files Doc source: https://www.facebook.com/groups/602529180853579/permalink/723427122097117/?fs=e&s=cl Model Source:...

I am very new to modeling and printing. See Print Settings Notes for further printing details. Print Settings Printer: Ender 3 S1 Pro Rafts: No Supports: Yes Resolution: 0.2 Infill: 20% Filament: Hatchbox PLA Black Notes: Supports: Printed with...

A stand for the LCD-Screen from the Ender3 pro

This is a remix of scottyujan's PSU cover for a Noctua fan upgrade for the Ender 3 https://www.thingiverse.com/thing:4794712. There you will also find the cover for the fan. Check out his YouTube video on his upgrades for the Ender 3:...

This is a remix of scottyujan's PSU cover for a Noctua fan upgrade for the Ender 3 https://www.thingiverse.com/thing:4794712. There you will also find the cover for the fan. Check out his YouTube video on his upgrades for the Ender 3:...

Just a fast-printable, minimalistic fix for holding my smokedetectors in place above my Ender 3 Pros. Will work with and without BLV dual-Z setup, setting the detector right above the middle of the bed while printing. Needs 2 M3 t-nuts, 2 screws...

... Good for ender 3, v2, or any other printer that uses same profiles as Creality. Left side designed to be exactly same length as the aluminum profile, and right side sticks out a bit. 12cm in length, verify that it not interferes with the z axis.

... just stops the annoying glare from hitting your eyes.  it does not affect platform lighting at all unfortunately the part is too long for an ender 3 bed so ull  need to print this model twice print is as simple as it gets no infill no support enjoy

... files. Can find other drawers if needed since he remixed the popular Ender 3 drawers by DWS_Design. Print the frame standing up, doesnt need supports. Print the drawer flat. ...I used tree supports touching bed to support the drawer handle.

... design</a>. ... I found out that he has the ender 3 PSU mounted on the outer side, but I have it on the inner side, so that it didn't fit. I redesined it, and added the hole to screw the piece to the printer for better efficency. ...

I'm planning on printing Teaching Techs' Ender 3 Electronics Case, which would leave a void where the factory electronics case sits. This remix is designed to complement the v2 case, which sits flush to the edge of the Y extrusion. Other remixes are...

I really liked the Ender 3 Tool Holder - 2.0! by Kiesling but wanted the extra drawers so here it is. The corner drawer was drawn in inches so please scale it to 2540. May 23, 2021 - Revision 1 - Corner drawer revised to be 60mm deep like the...

Ender 3 loom bracket. i made this to make my loom run on the front side for the gantry. help to keep it nice and secure and away from the lead screw at the back. also helps to keep it tidy going to the hot end / tool head. it simply slots onto the...

Ender 3 S1 Plus. ...I just used the printer's pwm output to control the laser power.The laser is powered by the source that comes with it.It looked great on my printer.I just recommend not using very high speeds due to the weight of the extruder...

This is a remix of CR83D's side PSU mount for the Ender 3. I remixed it in tinkercad to add the extrusion mount so no extra hardware is required. The main goal is to not make the user need any new hardware. This is a tight fit, but it doesn't move. ...I...

Here's a Wyze Cam V2 mount for the Ender 3 that mounts behind the control panel. You'll need to get slightly longer bolts. It does get in the way of the control knob a lil but you don't have to stretch you wrist around to get to it. It has wire clips...

This is a remix of Roma Aquatic's Stealthburner cooling duct for the Microswiss Direct Drive (https://www.thingiverse.com/thing:5178108); I just changed the location of the mounting holes to make it suitable for the regular Ender 3 X carriage. ...I...

I didn't like the idea of wedging the screen mount between the frame pieces on my ender extender so I made this screen holder that slots into the D slot on the front rail. It also adds a nice finishing touch to the front of the printer so there's...

Print quality is not the best either as there was not much tuning done before the enclosure was built :DFrontBackOverviewGrillPrinter UpgradesList of Printer UpgradesIf anyone is curious about the various upgrades I did to my Ender 3 Pro, here they...