ender 3 pro hot end upgrade 3d models

I'm excited to share my spin on the Creality Ender 3 Hot End Assembly! This design is specifically tailored for printing without any support structures, which makes it a game-changer for 3D printing enthusiasts. Two 5015 fans are required to make...

Ender-3 Hotend Cooler Fan Cover It's a hot-end cooler cover for Ender-3 printers. A protective cover designed to prevent premature wear on the fan due to filament strands getting sucked into the cooler. ...This ensures optimal performance and longer...

I didn't like the way that the tube and cables were unconstrained at the top of the hot end. There are two versions - the "Touch" version has an extra loop to zip tie a BL or CR touch cable. The regular version omits this loop. I have a CR...

This is my take on the Creality Ender 3 Hot End Assembly, Designed to print without support...! Takes two 5015 fans No air bleeding out from the hotend cooling fan and hitting the heat block and nozzle It works. STEP files are included P.S. didn't...

Hot end cover meant to allow for a Noctua NF-A4x10 FLX 12v fan in the hot end, and a down-firing LED strip (3x). Designed to work with - https://www.thingiverse.com/thing:4717877 <h1>Bill of Materials</h1> - Notcua NF-A4x10 FLX -...

Printed the dial gauge holder from kyoday which fitted my Ender 3 fine but didn't hold my [Mitutoyo 2046...

This is my take on the Creality Ender 3 Hot End Assembly, Designed to print without support...! Takes two 5015 fans No air bleeding out from the hotend cooling fan and hitting the heat block and nozzle It works. STEP files are included P.S. didn't...

## WHY I DID IT ## The standard noisy 40mm hot end fan on my Ender 3 started to wear, go into resonance and get really noisy so rather than just replace it I decided to upgrade it for a significantly quieter one. After some research on flow rates I...

I had trouble with Luke's hot end fix on my Ender 3 Pro because whenever I tried to get the filament up to the nozzle it seemed to get jammed. I hypothesized that the washer was moving around and not staying concentric with the tubing. Tried a few...

This is a rough first attempt at a hot end housing for the Ender 3 V2. Pre tap the holes with an M3 tap and for the fan screw bosses, thread the screw in carefully first then back it out and install the fan. Print as it sits on the printer with...

You may have seen a hot-end cover for the Ender 3 V2 around, only to print it and find nothing fits, the screws holes were all out of alignment etc. Fear not, this version actually fits (with lots of proof pics) The cover intakes were all printed...

This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/2yqV7XiBsCt

print with face down print in abs or petg .2 20%

I remix this one because i'm searching for somthing more compact and more design for my ender 3 pro https://www.thingiverse.com/thing:4635951 Now we can have the fan inside

I remix this one because i'm searching for somthing more compact and more design for my ender 3 pro https://www.thingiverse.com/thing:4635951 Now we can have the fan inside

The Human uses a chain and hot end coupler for keeping things organized.

This is the cover (that actually fits perfectly) for the Creality's Hot End named Spider. ... Edited: Added BLTouch support.

Complete upgrade\remake packet for ENDER 3 \ 3 Pro v1 to DIRECT print head with BMG extruder and E3D Volcano hotend. All parts makes together fully useable and long-time useable 3D printer for 24\7 printing withoutt any issues. This SET is only for...

Looking at the Ender series extruder cover, you realize that they just designed that extruder cover which hosts both hot-end fan (HEF) and print fan (PRF), as simple as it could be and without considering the airflow of the fans which is very...

This is an LED light bar for a Creality Ender 3 v2 printer. ...Allows better viewing of the printing process.

DOESN'T WORKS FOR COOLING PLA Low porfile to avoid hitting the bed and the clips Piece to block the air from the hot end fan to avoid wrapping in ABS parts. ... Uses stock secondary fan bolts.

Regardless, I've replaced all TMC2130 V3.0 SPI boards, fans, hot ends, and rewired everything basically from scratch. I also wouldn't recommend putting the control board under the Lack Table enclosure - it's a nightmare to work on. Here's a video...

Hardware needed for installation OMG extruder https://a.co/d/5EBCMJK Pheatus Dragon WHF and or UHF or equivalent size ( most sites show dimensions) and everything that is needed to operate the liquid cooled hot end. -you will need the liquid cooler...

Ender 3 MAX shroud for 60mm fan when using stock layer 4010 fans, cr touch can still be attached on stock mounting location.

... from the Delicate Filament Release Mechanism, Reducing the Risk of Damage or Interference. A Small yet Effective Cable Tie Secures the Hot End Cable to the Support, Providing a Clean, Tension-Free Path for Smooth Operation and Easy Maintenance.

When printing FedorSosnin's Hot End Mount, the printer knocks it off as it homes in on the X axis. To prevent this from happening all the time, I used Meshmixer to move the cable chain mount over to one side. ...It was designed to work perfectly with...

Revision of a design by Technivorous on: https://www.myminifactory.com/object/3d-print-technivorous-ender-3-v2-mod-pack-134327 Added version for 40x20x20mm fan, but didn't print or test fit it. Note the print instructions. ...

Protects against micro threads from entering and potentially jamming up the front cooling fan on a Creality Ender 3 printer, thereby extending its life and improving print reliability. ...It securely attaches to the top fan housing mounting...

I repositioned the "Arm" bracket to prevent the drag chain from colliding with the vertical aluminum stock when the X-axis reaches zero position, also increasing its height to match that of the mounting bracket at the opposite end of the drag chain.

Yet another ender 3 pro 10mm belt upgrade