ender 3 pro filament 3d models

Essential component for properly aligning the filament within the Ender 3/Ender 3 Pro extruder.

Remixed filament guide for Ender 3 / PRO / V2 with metal dual gear extruder.

Filament guide for the Ender 3 (Pro) - can be attached anywhere to the v-slot profile frame. ...I use it to guide the filament from the rear spool holder over the top frame and then down to the direct drive extruder.

Filament guide for the Ender 3 (Pro) - can be attached anywhere to the v-slot profile frame. ...I use it to guide the filament from the rear spool holder over the top frame and then down to the direct drive extruder.

This is a simple all-in-one filament guide and z-axis stabilizer for the Ender 3 Pro. With the use of a ball bearing, the z-axis stabilizer will support the top of the threaded rod while printing. Feel free to customize as needed. No extra pieces...

the original was not firmly enough in the profile of the ender 3 pro, i fixed that and made it a little less angular.

Designed to fit Ender 3/Pro existing spool tube, diameter 30mm. Edge on the tube needs to be cut off to slide the bearing on. To secure the bearing on the tube, I've drilled small hole through and put R-pin in. Might need some slight sanding on the...

3-5-2022 Filament Guide for My Ender 3 Pro. I tried several guides and none was exactly lined up straight. I created this and the bigger radius allows for you to center this up without a problem. Uses one of the stock screws for the lead screw...

Simple remix, adapted to use generic, cheap 3-pin filament detection sensor you can buy online, such as http://bit.ly/2JjjDnk Also change dimensions a little to align the filament better on my Ender 3 pro. You will have to print parts for the bearing...

After searching through several versions and remixes using old Z-axis endstops as filament runout sensors, none seemed to match my Ender 3 **PRO**'s endstop perfectly. Now one does exist. I printed it out, installed the endstop, and tested with a...

I remixed the version for the Ender 3 to match the dimensions of the Ender 3 Pro. Ionize's version had the guide and sensor 4mm over to the left which didn't leave a straight path for the filament. The sensor I used is a cheap one from aliexpress...

Also, I didn't want to remove both screws to put it in place, as I leave them a little loose to prevent binding on the z screw that the Ender 3 pro is prone to. With the one screw design, I could tighten the screw on the left that holds the guide on,...

I designed a custom spool holder for 75mm hole spools, similar to those used by Geeetech, as a solution to the issue of rough rolling on my Ender 3/Pro spool holder. ...The existing design caused unpleasant loud bumps when spinning.

This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/5CiFX1Yf8qr This is a remix which has a 5mm shifted top-part for using with an alu extruder on Ender 3 Pro. Thanks to Dezhe! ... Have phun!

... This is a customized remix, featuring a 5mm offset on the top component for seamless use with an aluminum extruder on the Ender 3 Pro. I'd like to extend my gratitude to Dezhe for their contribution. ...Have fun experimenting!

With my spool holder mounted on top, the filament had a sharp angle entering the inlet, which was likely due to my Ender 3/Pro setup. I appreciated the original design's use of PTFE tube as a guide and upgraded mine accordingly. Cutting a section...

I like the Ender 3 filament guide remixed by _HAL9000_ . It is clean and stable. However I already have the dual Z and stabilisers installed so I don't want to disassemble it and set up again. So I remove a portion from the _HAL9000_ model to allow...

I couldn't find a filament guide that suited my needs so I made this one that uses the bearing from the original extruder bracket that I had left from upgrading to an all metal one. The guide prevents the filament from snagging on the sharp corner...

Combined the runout sensor with guide by blaiseb (https://www.thingiverse.com/thing:3357097) with the attachment method of the runout sensor by murphmandan (https://www.thingiverse.com/thing:4337798) To physically attach the sensor and guide to my...

Remixed the "Ender 3 Filament Sensor and guide" by rghawi in order to add some chamfer to the piece so that these sensors (see below for link) would fit. ...Previously, the sensor was so big that the button was pressed with it in the sensor guide (need...

This is a remix of [Filament Runout Sensor w/ Creality Limit Switch](https://www.thingiverse.com/thing:4547442) The original Sensor is good, but I created this remix because I needed a sensor for my Ender-3 Pro and it is in an enclosure. The...

The stock Ender 3 Pro reel holder is rather simplistic and fitful. I searched for a better solution with bearings but not the end cap design you have to mount to the spool hub every time. I also didn’t want a 15 hr print job. I decided to use...

Remixed filament guide to align the filament path with the Bantam Feeder - https://bantam.design/feeder

The filament guide now sits perfectly perpendicular to the print bed.

Also after 1 month, I noticed the gear became loose and sometime was detached from base when changing filament. So I did this remix to address these minor issues. 1) The base's U shape was widened 3mm to insert smoothly and to match with the...

Remix of https://www.thingiverse.com/thing:4050500 I made the filament guide sit perpendicular to the bed. ... Category: 3D Printer Extruders

This is a filament cleaner for Double gear extruder. ... You will need your original extruder guide bearing, 7mm nuts, M4x12 screw and pieces of foam.

... This works well with OctoPrint and the enclosure plugin. You can add a rubber band or small screw to the end of the sensor arm to make sure it closes firmly when the filament is out.

I had a spare microswitch for the Z-stop after installing a BLTouch, so I made it into a filament run-out senser, re-use the factory screws and mount to Z-axis where the lead screw mounts.

Created a larger filament drip tray. Got tired of all the pieces falling in the aluminum extrusion gaps. Grab by the tip easy disposal. No supports needed! Clears most printed fan covers. Print vertically. ...