ender 3 pro filament not feeding 3d models

... than opening the controller board case and plugging it in there. Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: No Resolution: 20 Infill: 10% Cubic Filament: CCTree PLA Fluorescent Red Category: 3D Printer Accessories

A set of parts to relocate the filament spool from the top of the ender 3 to the side. Most side mounts seem to have the filament perpendicular to the machine vastly increasing the footprint. This one has the filament parallel to the machine with a...

You'll also need to print the following files: - "01_main_arm" (1 unit) - "02_sec_arm" (1 unit) - "03_wheel" (3 units) - "04_wheel_shaft" (4 units) - use 100% infill for optimal results Optional components include: - "05_wheel_cover" (3 units) Don't...

I finally got irritated enough with the swinging and scraping of the filament reel on the stock Ender filament holder. This is the result! This design simply fills the space between the original holder and the hole in the reel and was designed to...

I just got started 3D Printing and saw that there was a filament guide that also held that also held the z axis cable. The video I watched stated the Ender 2 one would work. Well.. it didn't. ...This is the first item I made using an STL file and 3D...

These rollers eliminate noise caused by friction between the filament and the edges of the hole when the extruder retracts. 3. A list of required materials includes 2 x F695-2Z-EZO rollers and 1 M5x20 CHC Screw. 4. This design adds some complexity to...

Not really a remix, Just an arm I designed for the filament filter, mostly to clean dust off filament and to use as a guide. It is a tight fit but it does fit. ... Filament Filter: https://www.thingiverse.com/thing:492067 It may work on other printer...

I created a new spool holder for my Ender 3 using two skateboard bearings, a 1-1/4"x5" bolt, two 1/4" nuts, and two 1/4" large fender washers to eliminate printing errors caused by the stock plastic holder's drag.

Filament end sensor for creality ender 3, ender 3 pro, ender 3 V2 etc. Requires 2 screws to fix your sensor to the print. ...(optional) You can add a screw to fix it to your printer chassis.

... a M4x10mm screw. Since the turning angle of filament on the top is not sharp, bearing is unnecessary. Filament filter is redundant to me. Just keep it simple and stupid. I printed it using PETG with rafts. ...But it is optional if you use PLA.

I made this spacer because I could not find one that fit the spool on my printer arm. ...This has a larger hole to slide over the spool on the printer. I also made it a bit long so there is not a lot of side to side movement of the role of filament.

Filament guide for direct drive extruder.

Filament rotation improvement through reduction is crucial.

While I love the clean and simple design of Sebastiandruckt's version, I did find that it makes filament change quite annoying because the filament exit is offset from the extruder's filament-in port. This is an attempt to fix this. Also, the...

Filament guide for up. V2 - nuts. ...V1 - binder clip.

A hook that holds the filament in place (better) use a short piece of 1.75mm filament as the pin

But if there was a filament snag, the connectors would snap or damage, needing replacement, and at the same time, the filament started cutting into the ring guide. I needed something better. a more stable connector, that was less prone to...

Minimalist filament guide, mounted uder spool arm, no extra screw requied.In my opinion the best filament is PETG but i havent tried this with other filaments Printing time is around 30 min.

I build this to help center the filament since the gap between the filament reel and the shaft of the native support is too big.

UPDATED (4.06.2021) - Improved TIGHT FIT to printer frame Simple filament guide - Easy snap in - No supports - 1.75mm filament

I wanted an enclosure for my Ener 3 pro to print ABS with greater ease. I required a thermal blanket, but it needed additional support, so I designed the Longarms to hold it in place. The spool holder posed a challenge, so I created a holder that...

I utilized blue PETG filament at a 0.2mm layer height with an 80% infill setting.

I did it because I never know where to leave the filament I don't use.

i wanted a longer guide to get the filament going in better. ...

I did it because I never know where to leave the filament I don't use.

Changed to Double Roller setup for side mount spool holder.Slides onto Filament Runout sensor bracket.

holds a generic filament sensor from amazon with mounting holes off to the side vs in the center snaps on the end of the frame near the Z scew on top. ...only for stock top filament roll holder.

No screws, no supports, 608 ball bearing filament guide designed to fit in the Filboyt filament guide mount. Combine with thing:4683505 (lower) for a complete the set of no screws, no supports, upper & lower filament guides. ... In the pictures the...

... The filament sensor is still located on the printer with this clip: https://www.thingiverse.com/thing:5419960 I also used a PTFE tube to get the filament inside the cabinet. ...Mounted on the sensor with: https://www.thingiverse.com/thing:5346708

This keeps your roll in one spot when its narrower than the spool holder, keep the filament exist point centered. ...