ender 3 pro fan replacement 3d models

Modified holes to 4mm in order to use brass inserts, the original holes where 5mm (too big) DOES NOT NEED SUPPORTS Suggested Settings 3 Layer Walls 75% Infill PLA is ok, the heat does not reaches from the nozzle/hotend Nonetheless if you want more...

I installed a 40x40x10 fan instead of my broken blower fan.

Print at 11%

The stock fan on the Ender 3 Pro had a short lifespan, prompting a search for a quieter and more powerful replacement that runs on 24 volts like the stock fan. Most 40x40x10mm fans available in 24 volts are extremely loud or fail to provide...

I use my Ender 3 Pro a lot, and thanks to that, both my Hot end fan and Parts cooling fan both gave up on me. This gave me a chance to upgrade each of them to a 40x20 hot end fan and a 40x20 parts cooling blower fan. I designed this to support both...

I found no suitable solution to neatly mount TL Smoothers within an Ender 3 PRO, so I designed a replacement bottom housing that works perfectly with my purchased smoothers. To ensure optimal performance and prevent overheating, I've added ample...

It was hard to find a 40x40 24v fan near me so I design this support for 5015 fan. ... I really like Rocco 81-92 job on his parts and this is my little contribution.

This is a derivation of MrTeliP original Ender 3 Pro SKR Mini E3 Case. He was gracious enough to make the STEP file available which made the editing rather easy. ...I removed the openings from the cover, as I didn't want filament to fall into the case,...

This is a derivation of MrTeliP original Ender 3 Pro SKR Mini E3 Case. He was gracious enough to make the STEP file available which made the editing rather easy. I removed the openings from the cover, as I didn't want filament to fall into the case,...

... noisy while not inhibiting the air-flow. ... Design intent to make a modification that was safe for children and animals (preventing fingers, noses and toes from getting into fan blades). Before and after noise measurements made with an iPhone. ...

Ender 3 Pro PSU cover replacement to use silent and powerfull 60x60 12v fan

NOTE: For the mean while PSU i used the specific model (Ender 3 PRO) For the basic PSU (ender 3) i would pick the Generic model (it hase 4 holes on the mount side) NOTE 2: I inverted the polarity on the jst connector and before changing or unwiring...

... ... So I made a new one wich replaces the original one. I made it of 2 parts for easy printing. Assembled without additional material. For protecting the flat cable i also put some stripes of duct tape to it (see pic.) Fully optional. ...

I'd be happy to remix this for you, but it seems like I need a link to get started. ...Can you provide that again? I'm also excited to see how you plan to use BLTouch and the Creality CR-10/Ender 3 stock fan mount replacement on your project.

... upgrade will make the things cool faster with guided air flow. feel free to remix it the way you want. You can even add surround cooling tube to the same fan with some modifications which doesn't need the factory fan replacement to some other place.

This is the replacement to the Ender 3 Stock Fan mount. This is not the Fang. With the Side fan vent, the same airflow as Stock can be maintained. The nozzle can be clearly seen for low-height prints and timelapse. For Type-A Base, two additional M3...

- Balance mass version added.* *Hotend fan causing vibrations even orginal ender 3 fan. Replacing the fan is a good oppurtunity to modify. 1. Turn off the printer 2. Simply put the balance mass fan on the rotor 3. TURN A LITTLE THE PRINTED PART...

I busted the original ender 3 fan blades with my tool (and I used DanielMitchel's design to fix it) but then I replaced it with a much quieter chinese fan:...

This is for a replacement with a slightly wider hub, not the original 40mm fan of the Ender 3. Check the dimensions before printing! This is a remix of https://www.thingiverse.com/thing:4266433 (even though I did the design from scratch, but he gave...

I busted the original ender 3 fan blades with my tool (and I used DanielMitchel's design to fix it) but then I replaced it with a much quieter chinese fan:...

The Ender 3 S1 has been a great machine so far except for the loud hotend fan.  I had a spare 4020 blower fan so I designed this bracket to replace the one found on the sprite extruder.  Even at 100% I've found it to be quieter than stock,...

This is the replacement to the Ender 3 Stock Fan mount. It's definitely not the Fang.\r\nWith the Side fan vent, identical airflow as Stock can be maintained with ease. ...The nozzle remains clearly visible for low-height prints and timelapse...

This is a simple replacement hot end cover for the Ender 3 V2. I decided to design my own as I didn't like the existing ones on Thingiverse and they all had their flaws. The fan grill is printed separately, giving it a nice offset and also the...

This is a simple replacement hot end cover for the Ender 3 V2. I decided to design my own as I didn't like the existing ones on Thingiverse and they all had their flaws. The fan grill is printed separately, giving it a nice offset and also the option...

... allowing prints to cool faster and with greater precision. Feel free to customize this design as you see fit – adding surround cooling tubes is also an option that doesn't necessitate replacing the factory fan with a different one elsewhere.

Remix of OderWat's design for replacing the Ender 3 Pro's fan with a larger one. ...Modified to accomodate a 92mm fan.

I accidentaly broke two of my Ender 3 v2 neo fan blades when i was cleaning so I tried to fix it using this one: https://www.thingiverse.com/thing:4731510 and it doesnt fit so i made some adjustments to fit in the ender 3 v2 neo. To install,...

Honeycomb PSU fan cover for Ender 3 pro with holes for a 92mm fan.

PSU cap for Creality Ender 3 Pro with 70mm Foxcon fan and Buck converter LM2596

Remix of Ender 3 pro 120mm Fan Power Supply Cover by Salabasti