ender 3 pro fan duct 3d models

This is a remix of https://www.thingiverse.com/thing:3676132/files designed to slide over the stock fan bracket on the ender 3 with my Volcano hot end. ... 4x m4 screws One of the screws holding the stock cooling fan on 60mm fan

WIP Had issues with overhangs, not being printed nicely at the back of the models, so I wanted to try with circular fan duct. Couldn't find one, built one on my own. I printed it vertically, using tree support, build plate only. ...I also used brim...

The original duct was lower than my nozzle, so I shortened it. There are 2 versions, the "flat" one and the 2mm one. ...The flat one, once installed will be tilted to point down towards the print, the other will be perpendicular to the nozzle.

I re callibrated my ender 3 pro, from the flow rate to e-steps to x, y and z movement. After that and running this new fan duct... I got results you see in the pics. ...Running a stringing test i had 0 stringing, was very surprised but also very...

I had to fix the position of the circular duct to fit with my Ender 3 S1 Pro Nozzle. ... Great upgrade to reduce stringing etc.

So i modded the original Ender 3 Pro Mainboard Metal Cover to fit two fans and directly blow onto the stepper heat sinks. Of course also used a step-down converter to run the 12V fans at 8V, so that they are very quiet now. ...Additionally used TPU...

I remixed the settings to match my Ender 3 Pro purchased in December of 2019. You may need to check the original files if your printer requires a second set of tabs. No built-in supports are available, so external support is necessary. I use 10%...

I manually put some internal supports, but it doesn't interfere with the airflow, so you can print completely without support. In the small lock that is on the outside, I also put a support manually, just remove it with a blade. ... Attention: I...

Some people, like me, were having trouble printing with certain types of materials, because of the supports. I did this remix, and manually placed some internal supports, however it does not interfere with the air flow, so you can print completely...

<p>Printed it in vertical position, using tree supports with brim.</p>

EN: I wasn't satisfied with the original fan duct from the Ender 3 S1 Pro because it didn't offer me good cooling on the back. After countless attempts with different fan ducts with no real result (image 1-5 including my own remix) I decided to...

Here is a fan duct with dual part cooling for the Ender 3 (Pro)."Unibody" versionFor the assembly you need:1x 3510 fan2x 3010 blower fans2x M3x6 screws1x M3x12 screwAssembly: First insert all fans into their places (M2 screws for the blower fans are...

Here is a "unibody" remix of my previously designed fan duct with dual part cooling for the Ender 3 (Pro). For the assembly you need: - 1x 3510 fan - 2x 3010 blower fans - 1x M3x12 screw - 2x M2x5 or M2.5x5 screws (minimum) Assembly: First insert...

Here is a fan duct with dual part cooling for the Ender 3 (Pro). For the assembly you need: - 1x 3510 fan - 2x 3010 blower fans - 2x M3x6 screws - 1x M3x12 screw Assembly: First insert all fans into their places (M2 screws for the blower fans are...

Here is a fan duct with dual part cooling for the Ender 3 (Pro). For the assembly you need: - 1x 3510 fan - 2x 3010 blower fans - 2x M3x6 screws - 1x M3x12 screw Assembly: First insert all fans into their places (M2 screws for the blower fans are...

Currently my latest version for Ender 3/Pro with 4 wheel cart (from Aliexpress) for Direct Drive and BLTouch. ...I lowered the height of the air tunnel a bit for better visibility of the hot end.

2in1 Fan duct and part cooling for Ender 3 / 3 Pro Simple and effective design.

Manta redesign https://www.thingiverse.com/thing:4403017 and https://cults3d.com/en/3d-model/tool/manta-compact-fan-duct-tool-change-system from BoothyBoothy for my Ender 3 pro, I wanted to use the factory fans and adapt another one from the same...

Ventilation duct for Ender 3 pro controller board. Necessary for closing the printer (to print ABS), with it the plate can be cooled, just connect a hose. Duto de ventilação para placa controladora Ender 3 pro. ... Necessário para o fechamento da...

Rediseño de Manta https://www.thingiverse.com/thing:4403017 y https://www.printables.com/es/model/169185-manta-compact-fan-duct-tool-change-system de BoothyBoothy para mi Ender 3 pro, quería utilizar los ventiladores de fábrica y adaptar otro del...

Rediseño de Manta https://www.thingiverse.com/thing:4403017 de BoothyBoothy para mi Ender 3 pro, quería utilizar los ventiladores de fábrica y adaptar otro del mismo 4010 para tener doble ventilador de capa. ... Tornillería: Tornillos 8mm y tuercas ...

I designed this mod to adapt the dual layer fan on my Ender 3 pro, my design part of the design of the VORON 2.4, I downloaded it ".step" file from their GitHub and proceeded to redesign, modify and adapt to my Ender 3 pro, it also includes a dust...

Fan Duct for the Creality Ender 3 Series and CR Series This fan duct was copied from the Zortrax M200 because it cools but does not directly hit the nozzle, keeping it stable. Its extrusion filament cooling efficiency is superior to that of the...

Remix of Gabriel3DCaster's "CR-10 Fan Mod - Airflow Optimization" I redesigned the original setup because it was bumping into my Ender 3 Pro's silicone cover, causing warping issues. ...To resolve this problem, I modified it to be slightly taller,...

Ender 2 Pro / Ender 3 - 5015 part cooling fan duct with easy to install magnetic mount. Compatible with separate CR touch mount. Minimalist, compact and flexible design. This design has considered easy remix of your own mount for other printers. -...

Ender 3 S1 Duct Fan upgrade with (4020) with Zero Y offset plate. ... X offset is -46mm Y Zero offset!

https://www.thingiverse.com/thing:3864519 https://www.thingiverse.com/thing:3115750 Creality Ender 3 Pro stock hot end mount for 5015 fan duct. I had to turn the 5015 to fit with my direct drive upgrade. This was printed on my Ender 3 Pro. I have...

... form factor of the printer if possible, so I created this. This duct allows the addition of 4010 fans underneath the Y-axis of the Ender 3 Pro. ... I have two of these so that I can use 2 Noctuas in _series_, so that they run at the default 24V.

I had big prints with some stringing, and the front fan of the ender 3 kept pulling in air just above the printed parts and pulled the pla strings onto the hot end. This duct changes that airflow so that air is pulled from above. The Parts is just...

To be able to test out the design from NEbie and mount on an Ender 3 / PRO, first i had to make some changes and new parts. Changes: . extruder clamp - original was rubbing the X axis profile . left mount - added the ability to screw from the back...