ender 3 pro fan duct 3d models

841179 3d models found related to ender 3 pro fan duct.
Ender 3 Pro Fan duct
Ender 3 Pro Fan duct
thingiverse

I decided to design a new fan duct with modifications to ensure enough room between print and fan duct as well as broadened the output to avoid too much air cooling in one spot. In my opinion it produced better printing results. ...You are welcome to...

ender 3 pro fan duct 4040
ender 3 pro fan duct 4040
cults3d

fan duct for ender 3 pro with 40mm fan

ender 3 pro fan duct 4040
ender 3 pro fan duct 4040
thingiverse

fan duct for ender 3 pro with 40mm fan

Creality Ender 3 Pro fan duct - remixed
Creality Ender 3 Pro fan duct - remixed
thingiverse

also filled some grooves inside the duct cause they were causing thin wall conditions Used the MS 3d builder so it doesnt look clean but it does the job I printed it at 45deg, with no inside supports to minimize bridging, looks like it would also...

Ender 3 / Pro Fan duct for 40x40x20 Noctua
Ender 3 / Pro Fan duct for 40x40x20 Noctua
thingiverse

A simple Ender 3 / Pro fan duct to attach a Noctua 40x40x20mm (Noctua NF-A4x20 FLX) fan instead of the original one. The original part-cooling fan can be attached on the right side. You can use all the original screws. Be careful: The Noctua Fan...

Satsana Ender 3 Pro Fan duct direct drive
Satsana Ender 3 Pro Fan duct direct drive
thingiverse

Satsana_5015 Duct Fan Remix V1 - Logos inserted - 5015 duct fan cable guidance inserted - Right exterior wall reinforced and holes for BL Touch removed Version V2 - Cable guidance replaced through hole - Cable tie hole relocated to the outside

Ender 3 pro fan duct with led and BL touch
Ender 3 pro fan duct with led and BL touch
thingiverse

This design brings the BL touch very close to the nozzle and accommodates two 40mm fans for good cooling. I run the hot end cooler blowing outward "away" from the printed parts. The design is meant to have 3mm brass melt-in inserts where needed...

Ender 3 pro fan duct stock parts
Ender 3 pro fan duct stock parts
thingiverse

Remix of thrutheframe design, who he provided the STP file for. The base comes with or without a mount for a dail indicator or dial gauge Everything mounts on using the stock hardware. ...

Ender 3 Pro Fan Duct/Direct Drive
Ender 3 Pro Fan Duct/Direct Drive
thingiverse

I merged the two original files directly into Tinkercad, creating a hasty fusion that requires further refinement. This untested composite still needs to be polished and refined before it's ready for prime time. ...If you spot any errors or...

Creality Ender 3 Pro Fan Duct
Creality Ender 3 Pro Fan Duct
thingiverse

This version is based on models from https://www.thingiverse.com/thing:4503104 and https://www.thingiverse.com/thing:4325909 Thanks to submano for the original idea

Ender 3, Ender 3 Pro fan duct for stock fan - Supported
Ender 3, Ender 3 Pro fan duct for stock fan - Supported
thingiverse

I found this fan duct on Thingiverse ( Ender 3 Pro stock fan ) and it is really looking good, I am pretty sure it is much better than the original part. It fits perfectly to my hot end. Unfortunately one side is sloped and it is difficult to...

Ender 3 (& Pro) Part Fan Duct
Ender 3 (& Pro) Part Fan Duct
thingiverse

=============================================================== Introducing a Fresh Take on the Part Fan Cooler Duct This innovative duct is specifically designed to elevate ABS/PLA printing. It boasts three key functions that work in harmony to...

Ender 3 Pro Cooling Fan Duct
Ender 3 Pro Cooling Fan Duct
thingiverse

277 / 5.000 Vertaalresultaten I designed this because the stock fan duct was no longer blowing air where it should with my MK8 hot end. I also designed it in such a way that the hot end fan no longer overrules the cooling part fan. ... Must be printed...

Ender 3 Pro Cooling fan duct
Ender 3 Pro Cooling fan duct
thingiverse

I had a problem with the ears that hold the fan on the original so I added some reinforcements

Stock Ender 3 Pro 5015 Fan Duct
Stock Ender 3 Pro 5015 Fan Duct
thingiverse

Modified holes to 4mm in order to use brass inserts, the original holes where 5mm (too big) DOES NOT NEED SUPPORTS Suggested Settings 3 Layer Walls 75% Infill PLA is ok, the heat does not reaches from the nozzle/hotend Nonetheless if you want more...

Satsana Remix Ender 3 Pro Fan Duct 5015
Satsana Remix Ender 3 Pro Fan Duct 5015
thingiverse

Logo inserted - Fastening holes relocated outward.

Mistral-E V1.3 Remix - Fast Ender 3/pro Fan Duct
Mistral-E V1.3 Remix - Fast Ender 3/pro Fan Duct
thingiverse

This is a remix of Mistral-E Filament Cooling Duct. ...I added a "shield" to prevent stock hotend cooling fan to flow over filament.

Ender 3 Pro Dual Fan Duct 5015 support direct drive
Ender 3 Pro Dual Fan Duct 5015 support direct drive
thingiverse

I've edited and upgraded my Ender 3 Pro printer to include a dual fan duct, specifically designed for use with 5015 fans, which provide direct drive capabilities.

Ender 3 Pro Round Fan Duct for 5015 Blower
Ender 3 Pro Round Fan Duct for 5015 Blower
thingiverse

Updated the design made [Tevo Tornado Round Fan Duct for 5015 Blower](https://www.thingiverse.com/thing:2842573) to fit on an Ender 3 Pro with a Silicon cap.

Ender 3 pro fan mount / duct (MinV2 remix)
Ender 3 pro fan mount / duct (MinV2 remix)
thingiverse

This fan duct should fit every Creality printer with the same hot end base plate like the one used for the Ender 3 pro. The back plate is necessary the keep the air flow away from the heating block. Modifications: -Hook added to fan mount to mount...

Ender 3 pro fan mount / duct (MinV2 remix)
Ender 3 pro fan mount / duct (MinV2 remix)
prusaprinters

I really liked his design but mounted to Ender 3 pro, the fan mount was a bit loose.This fan duct should fit every Creality printer with the same hot end base plate like the one used for the Ender 3 pro. The back plate is necessary the keep the air...

ADKS - Ender 3 Pro/St Fan Duct v3
ADKS - Ender 3 Pro/St Fan Duct v3
prusaprinters

Thank you!Paypal.me link: https://paypal.me/adarkstudioThank you page: https://pastebin.com/raw/gTt8iE5aCheersNio (ADKS)Previously…In an attempt to quiet my Ender 3 Pro, I designed this hotend fan duct to use 4010 or 4020 silent fans only. ...The other...

Part cooling booster - Ender 3 Pro side fan duct
Part cooling booster - Ender 3 Pro side fan duct
prusaprinters

Instead of adding more fans on the printer head where it adds weight and make it sometimes ugly huge to be effective, this puts the blower on the side of the X axis beam and so it isn't putting any more weight on bad places while still adding much...

Ender 3 S1 Pro Fan Duct / clone from stock / 5015
Ender 3 S1 Pro Fan Duct / clone from stock / 5015
thingiverse

The FAN duct is as close to the original as possible, but has a little more distance to the hotbed. The design has no corners, so the air can blow straight from the blower-5015 to the nozzle. The air from the blower is taken from the hotbed as in...

ender 3/pro volcano fan duct version 2.8
ender 3/pro volcano fan duct version 2.8
thingiverse

Basically, I extended the fan outputs 10mm so it reaches the nozzle of a regular volcano hotend. WARNING: This model is untested, so I can't guarantee itl fit. I'm going to print it at a later date and edit this as follows. This model is split...

Ender 3 Pro - Cooling Fan Duct
Ender 3 Pro - Cooling Fan Duct
thingiverse

It turned out absolutely flawless and fell perfectly into place once printed! ...Be cautious when removing supports, as they can be tricky to dislodge.

Ender 3 S1 pro fan duct 5015 4020 Print NO SUPPORT
Ender 3 S1 pro fan duct 5015 4020 Print NO SUPPORT
cults3d

Fan duct for Ender 3 S1 You need 5015 fan, 3 m3 8mm. ...12.11.2022 UPADATE 4020 FAN

Ender 3 Pro  60mm fan Cooling Duct
Ender 3 Pro 60mm fan Cooling Duct
thingiverse

This is a remix of https://www.thingiverse.com/thing:3676132/files designed to slide over the stock fan bracket on the ender 3 with my Volcano hot end. ... 4x m4 screws One of the screws holding the stock cooling fan on 60mm fan