ender 3 pro dual z 3d models

I recently moved my Main Board and Raspberry Pi to back of my Ender 3 Pro with this remix of Teaching Tech's rear case. That left me with tons of room in the front for storage. I remixed these drawers to make room for two of them side-by-side. I...

If you need it for the left side, just mirror it in your slicer. Edit: 8/30/19 The two cases were a bit too tight to fit, so I removed one edge width from the cases and bottom drawers for a better fit under the Z rail. I recently moved my Main Board...

Unlike the original design that stretched all the way to Y-axis belt pulley assembly, maximizing storage space, this revised design shortens the drawers to perfectly align with the right and left legs of the Ender 3 Pro for a sleek appearance. ... As...

Really enjoyed the original design and it didn't fit my Ender 3 pro with linear rails so I made the top drawer a tad shorter to clear the rails.The case was modified to clear.only the top drawer is shorter but still accommodates the nozzle holder.The...

Ender 3 Pro Z Axis Brace. Inspired by ProperPrinting, this modification corrects lean and improves rigidity. It works with power supplies located in the factory position and also functions with dual Z axes. Five-sixteenths-inch by twenty-four-inch...

Another iteration of the Z-Axis support designed specifically for the Ender 3 Pro printer, utilizing a 608-2RS 8mmx22mmx7mm bearing. This design aims to reuse existing screws and t-nuts from the z-axis sensor, previously replaced with the official...

This is specifically for the Ender 3 Pro with the upside-down bed bolts that scratch the other versions of this case design (without the cut-out). I didn't want to flip the bolts and mess up the bed level. Print upright to avoid center sagging...

I had issues aligning the original part on my Ender 3 Pro. To resolve this, I tweaked it by pushing the support further away from the mounting point by 1.65mm. Additionally, I elevated the bearing holder up by 11mm to ensure it's perfectly aligned...

Ender 3 Pro Z Axis Lead Screw guard. I needed a design that would perfectly align with the bracket, so cut outs were added to the bottom for crush rings to fit snugly inside. The lead screw guard is also adjustable to accommodate any necessary...

Please open photos at "fullscreen" (expand them) to see all details Recently I switched my Ender 3 Pro to dual Z (with belts) and I needed to move my PSU out of printer frame. I haven't found what I've needed, so I designed this extra rigid PSU mount...

I didn't like the barcode on the Z axis so I made a sleeve to slide over the part already there and decided to cover the screws on the right side as well. Bottom of Z axis right is open so no chance of rubbing on belt. I have put file in with and...

... with the belt. A file has been uploaded, featuring both versions: one including the Ender 3 Pro text and another without it, catering to users who might prefer the latter option. ... When printing vertically, support material will not be necessary.

Stock micro switches on Creality machines are cr*p they are too small, to flimsy and tend to catch oxides on contacts. Good for some time, then they start giving false positive, on Z axis its noticable.If your printer homes Z axis but you do not hear...

Drawers for the Ender 3 Pro are here. To print the case, place it on the back as shown. Have fun! UPDATE: February 27, 2019 If you're experiencing issues with drawers not fitting in the box, I've added V2 drawers that are a bit smaller. UPDATE:...

... the case and drawers. Note that this design is for the Ender 3 only. It will not fit the Ender 3 Pro since that printer has a wider center extrusion (40 mm instead of 20 mm). ... The case and drawers should print as they are with no supports.

Just got my BLV Ender 3 Pro Kit, but it seems it requires a BLTouch. I'm not a fan of BLTouch, so I didn't want to use it, and I wasn't having any problems with my Heatbed anyway. So, I decided to try using the Stock Z Min Endstop instead. However,...

This is my own take on a Z axis Belt Mod for the Ender 3 / V2 / Pro. it is based on the Voron 2.4 Z axis gearbox and extensively modified to work on the ender 3 platform. this is for use with duel z stepper motors and linier rails. other additions...

I'm planning on printing Teaching Techs' Ender 3 Electronics Case, which would leave a void where the factory electronics case sits. This remix is designed to complement the v2 case, which sits flush to the edge of the Y extrusion. Other remixes are...

Need better control of your Ender 3 Z Axis? Well, here you are. Rod side is not threaded, just push it onto the rod - it's pretty tight. ... 66mm circle diameter for quick adjustments.

...To fit this part into the bearing's inner ring, use the same heat trick and a small tool. Finally, make sure everything is properly mounted and centered. Check out a nice filament guide for Ender 3 Pro here: https://www.thingiverse.com/thing:4487170

I was not satisfied with the available Z-endstop mounting options for the Ender 3 Pro. I have been using https://www.thingiverse.com/thing:2816718 on my CR-10S and it works great but cannot be used because of the differences between the y-axis motor...

I'm planning on printing Teaching Techs Ender 3 Electronics Case (https://www.thingiverse.com/thing:3688967) which would leave a void where the factory electronics case sits. This remix is designed to compliment the v2 case which sits flush to the...

"Remix" to include different thickness .stl files. Print Settings Printer Brand: Creality Printer: Ender 3 Pro Rafts: No Supports: No Resolution: 0.16 Infill: 100% Filament: Generic PLA Any Post-Printing ============= Mount instructions (same as...

This part is intended to space out the z-axis motor from the metal structure on the Ender 3 Pro 3D printer. Over a long period of time, the stock spacing of the z-axis metal rod can be bent from too much pressure applied by the horizontal gantry. ...

This is just a small spacer for DWS's draw set for the Ender 3 Pro (https://www.thingiverse.com/thing:3416444). It essentially converts the box to fit a standard Ender 3. ...

I was not satisfied with the available Z-endstop mounting options for the Ender 3 Pro. I have been using https://www.thingiverse.com/thing:2816718 on my CR-10S and it works great but cannot be used because of the differences between the y-axis motor...

I finally made my own part after testing several models without any success, but this one works perfectly on my Ender 3 Pro. For the base, you will need longer screws to attach it securely to the printer, while the original screws for the motor mount...

I discovered that my Ender 3 Frame was severely unstable on the Z-axis, exhibiting a noticeable wobble from front to back and failing to maintain perfect right angles with Y. The braces are designed to be secured using hammer-nuts m5, although they...

Ender 3 Lead Screw Stabilizer. ... I fixed it because it didn't fit on the 20x20 bare metal.

Yet another Z-axis stabilizer for the Ender 3 or Ender 3 Pro. This one comes in two pieces and should be mounted with two M2.5x12MM screws and two M2.5 nuts. The stabilizer uses a 608 bearing that can be hold in place with a small scrub screw...