ender 3 pro direct drive upgrade 3d models

This is a Direct drive mount compatible with the ender 3 style carriages that uses the Slice engineering copperhead with the LGX lite The design is available in three options for the hotend: -rigid mounted copperhead (files without specific hotend...

EDIT 07/05/2021 : The knob works perfectly fine on a microswiss direct drive extruder, It helps changing the filament EDIT 22/12/2021 : This wheel allows to do cold pulls on the Microswiss REMINDER You might wanna check before printing that your fan...

This is a remix of Bart-tech3D's simple conversion to a direct drive extruder on Ender 3. ... The original can be found here: https://www.thingiverse.com/thing:3965738 this is designed for a stepper motor and a dual filament feeder that can be...

I've had direct drive for a long time and didn't have any cable management issues. After I installed the Ender Extender, I had to loop the cables over the top of the machine to keep them from dragging/snagging the bed. I designed this mount to clean...

I converted my Ender 3 v2 to direct drive, so i wanted to mount my filament spool like on Prusa's, but didn't want some chunky and time consuming print. So here it is EnderSpoolHolder Prusinator. It is made for M4 screw, also aded the screw...

I got this cheap direct drive plate for my Ender 3 since I cba importing the printermods plate which is actually a little taller than what the original part was made for. This increases the height of it by 2mm to compensate for it. NOTE: I also...

This is a remix of the [BMG + V6 + ABL Direct Drive Mount](https://www.thingiverse.com/thing:4441537) by [TwoPuncakes](https://www.thingiverse.com/TwoPuncakes) and the [carriage mount remix](https://www.thingiverse.com/thing:4675822) for the Ender 3...

I recently converted my Ender 3 V2 to direct drive. In order to best feed the filament I wanted to turn my spool 90 degrees. There were several good designs out there, but I wanted to add a little something to it. My basic design incorporates a...

... the Chiron that I designed. ...I used it on all 3 of my Chirons. It works great. I built new wiring harnesses for the Hot End and Bypassed the Hot End Circuit Board. The Probe alignment isn't perfect. ...Feel free to make your own adjustments.

I wanted a direct drive conversion for my Ender 3 V2 that did not require soldering, buying new parts etc... I followed the assembly guide from [Hard Firm Soft YouTube...

I have an Ender-3 V2 with a BIQU H2 direct-drive extruder. And I like mounting the spool holder on my printers, but this doesn't work super well with direct-drive extruders. So, I wanted to install a reverse Bowden setup to put the filament...

I designed a simple Direct Drive mount specifically for X-Axis linear rails on the Ender 3. The existing direct drive mount needed to be replaced after I added an x-axis linear rail, so I created this new one. M3 threaded inserts were used for the...

Hello, I recently modeled and tested a tab to make a creality Ender 3 v2 a direct drive.5 printer that should also work on other printers from creality but this has yet to be confirmed) This last one allows to print all kind of filaments including...

When I got a Sprite direct drive extruder for my Ender 3 V2 I needed to change the position of the spool mount and the best solution seemed to be something like the Ender 3 S1 with the spool held at 45 deg angle behind the top rail. There was an...

(And post a remix, by the way)It fits Nema Motors axle with a gentle pression.EDIT 07/05/2021 : The knob works perfectly fine on a microswiss direct drive extruder, It helps changing the filamentEDIT 03/02/2021 : This wheel allows to do cold pulls on...

I also made the rim taller so there's even less of a chance of the spool falling from the mount.For the “clip” part and print instructions visit the original design:...

This is a part that I am working on because there is a lack of upgrade parts for the Direct Drive upgrade. I just thought that the extruder stepper motor is ugly and was trying to make it look a little nicer and like some of the covers that are...

These parts are designed to be used with Benawhite's Ender 3 Direct Drive Adapter (https://www.thingiverse.com/thing:3386628). They replace the "stepper_spacer.stl" file, offering a spacer that provides support for the stepper motor and a filament...

Remixed from : Voron afterburner mount for Ender 3 (bmg direct drive) by igalopaka https://www.thingiverse.com/thing:4614384 BlTouch addon inspired by: Voron Afterburner with Bltouch for Ender 3, CR-10, etc. by TroyJoachim...

These parts are designed to be used with Benawhite's Ender 3 Direct Drive Adapter (https://www.thingiverse.com/thing:3386628). It replaces the "stepper_spacer.stl" file with a spacer that also provides a support shelf for the stepper motor, as well...

Remix to adapt the bracket for use with an Ender 3 Pro, The filament path is in a slightly different offset from the back plate. ... Note that the stl was saved in inches, you will need to adapt to metric on import to your slicer.

Hello Makers, Recently purchased a Micro Swiss direct drive extruder kit for my Ender 3 and CR10. Great gear, but there are some minor issues with limiting the print area in Z that I will work on soon. The quality of prints has greatly improved, and...

Hello Makers, Recently bought Micro Swiss direct drive extruder kit for Ender 3 and CR10. Great gear, there are small issues with limiting printing area in Z but I will work on it soon. Quality of print is greatly improved and I can finaly use Linear...

Satsana_5015 Duct Fan Remix V1 - Logos inserted - 5015 duct fan cable guidance inserted - Right exterior wall reinforced and holes for BL Touch removed Version V2 - Cable guidance replaced through hole - Cable tie hole relocated to the outside

Adjustable extruder moves swiftly from side to side for precise video recording.

needed a custom extruder motor mount since the one I had would no longer work with new set up. ... This uses 2- M3x6x5 brass inserts and tree supports printed in PETG.

You must have - 3X M3 20mm screw - 2X M3 nuts - 1X M3 self-locking nut

I remixed the gantry plate to make the incoming attachment point for the cables compatible with the cableChain_Xend.stl end piece from the OG cable chain. It also includes a chain attachment point for horizontal movement along the X axis. ...Just re-use...

Functional mix between #3584158 and #4336829

The designs for ender 3, ender 3 pro and ender 3 v2 are different, because they have slightly different X carriage plates. I have only tested the pro version because this is what I have. If you test other versions, let me know if they fit well. You...