ender 3 pro direct drive upgrade 3d models

I've remixed napfkuchen's BMG direct drive design to fit the Ender 3 V2's x-carriage as the mounting hole for the fan shroud is in a different location when compared to the Ender 3. The Bl-touch has also been added in as the two parts would...

This is a remix for the 4-Screw Filament Runout Sensor Mount for Ender-3 v2 with Direct Drive by RLovrin1. The filament sensor mount worked great, but I would have had to mount the filament itself directly above the printer. I preferred to keep the...

This is a custom direct drive plate designed for mounting the stock extruder and stepper motor on an Ender 3 or CR10 series printer, among others. The design also includes a modified Bullseye fan duct that removes the original wire harness, which...

This Bondtech direct drive setup requires an EZABL mount available on Thingiverse https://www.thingiverse.com/thing:3241793 The mount supports both standard 18mm EZABL and the smaller 13mm EZABL mini. For optimal results, use X +53 | Y -3 offsets...

I printed napfkuchen's titan direct drive adapter but hole locations are 3.5mm missed. ...SoI made the hole point fixed.And some minor adjustment to snug fit.

Due to my almost pathological need to make my own version of everything, I've come up with a direct drive mount for the Ender 3. It bolts onto the x carriage wheels in place of the spacers, resulting in a pretty solid build. So far, I'm getting...

This is an X-Axis mounted cable guide for the Ender-3/Ender-3 Pro. You can use the existing screws holding in the X-axis stepper motor to mount it directly. There are two ziptie spots, the ziptie anchor point on the back can be tightened to...

This was designed for a Direct Drive system that uses the original Ender 3 Filament and wiring design. The extruder replacement uses 2 PC4 x M10 connectors. and a short piece of PTFE tubing installed between them. Since this is in front of the...

... on import to your slicer. Print Settings Printer: Ender 3 Pro Rafts: No Supports: No Resolution: 200 Infill: 20 Filament: Generic PLA your fav Notes: Lay on bed so as to minimize/eliminate the need for supports. ... Category: 3D Printer Parts

... on import to your slicer. Print Settings Printer: Ender 3 Pro Rafts: No Supports: No Resolution: 200 Infill: 20 Filament: Generic PLA your fav Notes: Lay on bed so as to minimize/eliminate the need for supports. ... Category: 3D Printer Parts

When I first started out, I felt like it was a huge pain in the ass as well as a waste of filament trying to find a direct drive solution for my Ender 3 that would work with any of the standard available cooling solutions such as the Hero Me etc. I...

I created this because I needed a direct drive for my Ender 3 with the Ed3v6 + Volcano End. I couldn't find a version that kept the original extruder. You'll need approximately 65mm of PTFE (you can adjust the extruder height slightly). I...

When I first started out, I felt like it was a huge pain in the ass as well as a waste of filament trying to find a direct drive solution for my Ender 3 that would work with any of the standard available cooling solutions such as the Hero Me etc. I...

I originally tried the [Ender 3 Direct Drive Linear X-Axis Mount by vnomus427](https://www.thingiverse.com/thing:4433174) but I found that my direct drive wasn't the same size as the one that mount was for - I have a couple of centimeters of Bowden...

*******Updated Jan 11 2020 with link counts and spool holder\r\n******updated jan 15 2020 with correct drive mount link \r\n\r\nI'm Not the Designer, I Just Converted My Printers!\r\n\r\nNone of these designs are mine nor have they been altered or...

I remixed the Ender 3 direct drive mount for the Titan extruder and pancake stepper, designed by napfkuchen, to make it more rigid (with the original one the extruder assembly would bend slightly during retractions, with negative effect on stringing)...

This is a modification of the Satsana Ender 3 Fan Duct to fit an Ender 3D Pro direct drive with CR Touch. It has been further modified to split. There is a base that mounts to the printer and one bolt holds the Santsana to the base mount. This...

Please consider leaving a like, make or comment on PrusaPrinters Backstory I purchased one of the cheaper knockoff MDD v1.2 (Modular Direct Drive) plates and was unhappy when I found that the holes for the gantry plate were not aligning. Therefore...

The stock Ender 3 Limit Switch doesn't have a LED so I grabbed one that I had laying around and soldered it to the limit switch (along with its resistor). The screws are nylon M3 with nylon nuts... I bought a bunch of them 15mm to 20mm then just...

I designed the petsfang direct drive mod for the ender 3 or cr10 (https://www.thingiverse.com/thing:2963434) and discovered that at high extrusion rates, the extruder would be forced upwards and away from the hot end due to back pressure. The short...

I added a Dust Filter and a Filament Runout sensor to the direct drive mod. I installed a BLTouch, using the Z Limit Switch as a filament runout sensor. I noticed that the tip of the limit switch had to accept filament in both directions. If a...

This direct drive mount is a remix of the TEVO Tornado Bondtech BMG direct drive mount (remix), found at https://www.thingiverse.com/thing:3995514, courtesy of QCPassed. It fits the Ender-3 and will also fit the TEVO Tornado as well as the CR-10(S)...

... a 4020 blower fan. ... Designed at the request of thingiverse user madjax94 Fits Ender 3 / CR-10s (non-Pro) mounting points. ... Additional model included with adjusted mounting points for the 5-finned CR-10s Pro version of the Micro Swiss hotend.

I recently put the Official Creality direct drive upgrade and put a Slice heat break into it. The original is to tall to fit, so I cut off the top in 3D builder and printed this one. Fits perfectly... ...I love this fan shroud....I can print LW-PLA at...

The filament guide I designed for use with my micro swiss direct drive conversion. With the cabinet I built I couldn't really do top or side mount for the reel. So using this I can retain the original filament feed position and ender hardware. ...

After disappointing results with my own and the Basaraba Direct Drive Upgrade kit due to a lot of ringing- noise artifacts due to the additional inertia of the added motor weight on the Ender 3. I decided to experiment with a flexible shaft drive...

After disappointing results with my own and the Basaraba Direct Drive Upgrade kit due to a lot of ringing- noise artifacts due to the additional inertia of the added motor weight on the Ender 3. I decided to experiment with a flexible shaft drive...

Got this direct drive for an ender 3 from a friend and thought I would try to use it on my Megazero 2.0 So if you get your hands on this setup then this maybe for you I also have Ender 3 V2 which is already heavily modified so I does not need this......

Remixed specifically for an aluminum direct drive purchased directly from Trianglelab through the online marketplace Aliexpress.

... fans and direct extruder. ...If you want to use direct extruder it might be the best to use my mount https://cults3d.com/en/3d-model/various/ender-3-v2-direct-extrusion-mount-for-dual-gear Easy install with 1 screw. ...You might also need 2 doodly eyes