ender 3 pro damper 3d models

This is a remix of the damper spacer by matthijsp (https://www.thingiverse.com/thing:3245255), designed specifically for the Ender 3 Pro. To get started, simply print the one file provided in this remix and you can reuse most of the original Ender 3...

Ender 3 Pro damper feet 2x 2020 AL profile (40x40).Max feet load 3kg. ...Optimal load is 2kg per feet.Tight fit, you can enlarge model when you want more loose fit.Print material: PLAPerimeters: 5Supports: YES, for enforcers only

Ender 3 Pro damper feet 2x 2020 AL profile (40x40).Max feet load 3kg. ...Optimal load is 2kg per feet.Tight fit, you can enlarge model when you want more loose fit.Print material: PLAPerimeters: 5Supports: YES, for enforcers only

Ender 3 Pro damper feet 2x 2020 AL profile (40x40).Max feet load 3kg. ...Optimal load is 2kg per feet.Tight fit, you can enlarge model when you want more loose fit.Print material: PLAPerimeters: 5Supports: YES, for enforcers only

Model to be printed in TPU. ...Reduced some of the vibration transfered to the table by the printer.

remixed to allow m3×35mm screws with proper alignment

Four M4 screws, each measuring twelve millimeters in length, are required to secure four corresponding M4 nuts into place.

These are spring-based vibration damper feet designed for the Ender 3 Pro, with compatibility assured for the Ender 3 as well. The larger case part is the lower section where two springs need to be placed. Once those springs are in place, the top...

This spacer is specifically designed for the Ender 3 Pro and has only been verified to work seamlessly with the damper shown above. To function properly, a modification of the printer is required, but this modification can all be reversed if needed....

These are spring based vibration damper feet for the Ender 3 Pro (I think, that they should be compatible to the Ender 3, as well).The larger case part is the lower part in which you have to place 2 springs. Into that lower part you have to place the...

**It only fits the Ender 3 Pro with a 4040 center extrusion.** This bracket is needed because some Ender 3 Printers are shipped with pressed pulleys on the stepper motors. Those pressed on pulleys can't be adjusted along the shaft of the motor. All...

To address this issue, I have added support bars on part B, ensuring that the final assembly fits snugly around the rubber feet already present under the Ender 3 Pro. Note that it's unclear whether this revised version will fit the non-Pro Ender 3...

--- Hey guys, For the Ender 3 Pro, pulleys are now unfortunately pressed onto the steppers' shafts. To address this issue, I designed a Pulley press for both x- and y-steppers. You can put the stepper into the press using a M5x40 screw and a M5 nut...

I found that my Ender 3 pro has press fit pulleys on the X and Y axis stepper motors. I didn't want to damage them by trying to remove them and I wanted a better way to fit dampers on. I created this print so that I could use all the parts already...

I completely agree with you, CDeviant designed a piece that perfectly fits the Ender-3 Pro and it's incredibly sturdy. It just works seamlessly.\r\n\r\nWhen I installed CDeviant's design, I encountered a few issues:\r\n- The stepper motor was...

Something that was longtime postponed - Vibration dampers. If you want a really quiet printer, you can use these great looking vibration absorbers based on squash balls (two yellow dots). They are very easy to print. Your 3D printer will become...

We're not quite there yet - this isn't the finished product, it's a workable prototype with some issues that make installation a bit of a challenge. ...I'm planning on releasing an update soon to iron out those problems.

Yet another Ender 3 Storage container for the front This one is designed with the Ender Pro 3 in mind equipped with the damper feet installed and cable retention clips on the back rail. fits nicely in behind everything and pops in and out nice and...

* Slide the T-Nuts into the bottom profile and tighten the damper with them. * Screw the case on top of the damper with 2 screws. * Put the stepper into the case and screw it from the top. * Reassemble the threaded rod Done. Avoid touching the...

I tried MHprints' design for clip-on dampers and found out that Ender 3 Pro has thicker rubber feet. I had to add 3.5mm of height. ... Category: 3D Printer Accessories

I tested MHprints' clip-on damper design on my Ender 3 Pro, but it needed a tweak since the printer's rubber feet are surprisingly thick. ...To get a smooth print job, I ended up adding an extra 3.5mm in height to compensate for that thickness.

https://youtu.be/VboX4Ns1e4o The ender 3 Y axis stepper spacer for silencer damper.

FIT ENDER 3 PRO ONLY I removed the circular features from the bottom since my 9mm silicone pads didn't fit properly. I also optimized the clip's thickness and shape for faster printing and reduced material usage. The clip's thickness doesn't impact...

This mount is designed to work with these stepper motor dampers from Amazon (in case it goes down, it's listed as *"CCTREE NEMA 17 Stepper Steel and Rubber Vibration Dampers with M3 Screw Upgrade for Creality Ender 3 Ender 3 pro CR-10 CR-10S 3D...

I followed A_Make Designs' tutorial on Ender-3 stepper motor dampers with press-fit pulleys, but I realized I couldn't use his printouts or method for spacing the Y axis stepper for the damper. So, I created this one myself. For those who don't know,...

The original design performs admirably, yet I've discovered that it tends to sag under the strain of the motor's power over an extended period. ...To address this issue, the revised version incorporates two supplementary struts on the upright element,...

This offsets the Y-Stop by 12mm on an Ender 3 Pro to allow clearance for a Stepper Damper and Heat-sink upgrades. Please note that part of the sheet metal mount was Dremel'ed off (visible in cover photo) and 1 additional M3x6 was used to secure it to...

I made these dampers to try and reduce the noise of the motors on the newer versions of the ender 3 pros (2020). I originally bought dampers however it is a pain to install on these newer models. I designed a small damper to go in between the motor...

Both of the original mounts listed as sources for this file failed to fit my newly bought Ender 3 Pro. The X-carriage collided in multiple places with the bottom of the mount. Therefore, I reworked the file to fit perfectly on newer Ender 3 Pros (and...

I designed a straightforward adapter to enable using the Ender 3 damper, specifically created by redmaxver and available on Thingiverse as thing #2913473, on my own Tevo Tarantula Pro printer.